Surface preparation of powder metallurgical tool steels by means of wire electrical discharge machining

The surface of two types of powder metallurgical (PM) tool steels (i.e., with and without nitrogen) was prepared using wire electrical discharge machining (WEDM). From each grade of tool steel, seven surfaces corresponding to one to seven passes of WEDM were prepared. The WEDM process was carried out using a brass wire as electrode and deionized water as dielectric. After eachWEDM pass the surface of the tool steels was thoroughly examined. Surface residual stresses were measured by the X-ray diffraction (XRD) technique. The measured stresses were found to be of tensile nature. The surface roughness of the WEDM specimens was measured using interference microscopy. The surface roughness as well as the residual stress measurements indicated an insignificant improvement of these parameters after four passes of WEDM. In addition, the formed recast layer was characterized by means of scanning electron microscopy (SEM), XRD, and X-ray photoelectron spectroscopy (XPS). The characterization investigation clearly shows diffusion of copper and zinc from the wire electrode into the work material, even after the final WEDM step. Finally, the importance of eliminating excessive WEDM steps is thoroughly discussed

Low-intensity resistance exercise does not affect cardiac autonomic modulation in patients with peripheral artery disease

OBJECTIVE: To analyze the effect of a single bout of resistance exercise on cardiac autonomic modulation in patients with peripheral artery disease. METHODS: Fifteen patients with peripheral artery disease (age: 58.3±4.0 years) underwent the following sessions in a random order: resistance exercise (three sets of 10 repetitions of the six resistance exercises with a workload of 5-7 in the OMNI-RES scale) and control (similar to the resistance session; however, the resistance exercises were performed with no load). The frequency domain (low frequency, high frequency and sympathovagal balance) and symbolic analysis (0V, 1V and 2V patterns) of heart rate variability were obtained before and until one hour after the interventions. RESULTS: After the resistance exercise and control sessions, similar increases were observed in the consecutive heartbeat intervals (control: 720.8±28.6 vs. 790.9±34.4 ms; resistance exercise: 712.9±30.1 vs. 756.8±37.9 ms;

The Intentional Use of Service Recovery Strategies to Influence Consumer Emotion, Cognition and Behaviour

Service recovery strategies have been identified as a critical factor in the success of. service organizations. This study develops a conceptual frame work to investigate how specific service recovery strategies influence the emotional, cognitive and negative behavioural responses of . consumers., as well as how emotion and cognition influence negative behavior. Understanding the impact of specific service recovery strategies will allow service providers' to more deliberately and intentionally engage in strategies that result in positive organizational outcomes. This study was conducted using a 2 x 2 between-subjects quasi-experimental design. The results suggest that service recovery has a significant impact on emotion, cognition and negative behavior. Similarly, satisfaction, negative emotion and positive emotion all influence negative behavior but distributive justice has no effect

Active Galactic Nuclei at the Crossroads of Astrophysics

Over the last five decades, AGN studies have produced a number of spectacular examples of synergies and multifaceted approaches in astrophysics. The field of AGN research now spans the entire spectral range and covers more than twelve orders of magnitude in the spatial and temporal domains. The next generation of astrophysical facilities will open up new possibilities for AGN studies, especially in the areas of high-resolution and high-fidelity imaging and spectroscopy of nuclear regions in the X-ray, optical, and radio bands. These studies will address in detail a number of critical issues in AGN research such as processes in the immediate vicinity of supermassive black holes, physical conditions of broad-line and narrow-line regions, formation and evolution of accretion disks and relativistic outflows, and the connection between nuclear activity and galaxy evolution.Comment: 16 pages, 5 figures; review contribution; "Exploring the Cosmic Frontier: Astrophysical Instruments for the 21st Century", ESO Astrophysical Symposia Serie

Auger Effect in the High-Resolution Ce 3d-edge Resonant Photoemission

The bulk-sensitive Ce 4$f$ spectral weights of various Ce compounds including CeFe$_2$, CeNi$_2$, and CeSi$_2$ were obtained with the resonant photoemission technique at the Ce 3d-edge. We found the lineshapes change significantly with the small change of the incident photon energy. Detailed analysis showed that this phenomenon results primarily from the Auger transition between different multiplet states of the Ce $\underline{3d_{5/2}}4f^2$ (bar denotes a hole) electronic configuration in the intermediate state of the resonant process. This tells us that extra care should be taken for the choice of the resonant photon energy when extracting Ce 4$f$ spectral weights from the Ce 3$d$-edge resonant photoemission spectra. The absorption energy corresponding to the lowest multiplet structure of the Ce $\underline{3d_{5/2}}4f^2$ configuration seems to be the logical choice.Comment: 13 pages, 5 figures, submitted to Phys. Rev.

On the Effect of Nb on the Microstructure and Properties of Next Generation Polycrystalline Powder Metallurgy Ni-Based Superalloys

Abstract The effect of Nb on the properties and microstructure of two novel powder metallurgy (P/M) Ni-based superalloys was evaluated, and the results critically compared with the Rolls-Royce alloy RR1000. The Nb-containing alloy was found to exhibit improved tensile and creep properties as well as superior oxidation resistance compared with both RR1000 and the Nb-free variant tested. The beneficial effect of Nb on the tensile and creep properties was due to the microstructures obtained following the post-solution heat treatments, which led to a higher γ′ volume fraction and a finer tertiary γ′ distribution. In addition, an increase in the anti-phase-boundary energy of the γ′ phase is also expected with the addition of Nb, further contributing to the strength of the material. However, these modifications in the γ′ distribution detrimentally affect the dwell fatigue crack-growth behavior of the material, although this behavior can be improved through modified heat treatments. The oxidation resistance of the Nb-containing alloy was also enhanced as Nb is believed to accelerate the formation of a defect-free Cr2O3 scale. Overall, both developmental alloys, with and without the addition of Nb, were found to exhibit superior properties than RR1000.This work was supported by the Rolls-Royce/EPSRC Strategic Partnership under EP/H022309/1, EP/H500375/1 and EP/ M005607/1