Bottom-up Photonic Crystal Lasers

The directed growth of III–V nanopillars is used to demonstrate bottom-up photonic crystal lasers. Simultaneous formation of both the photonic band gap and active gain region is achieved via catalyst-free selective-area metal–organic chemical vapor deposition on masked GaAs substrates. The nanopillars implement a GaAs/InGaAs/GaAs axial double heterostructure for accurate, arbitrary placement of gain within the cavity and lateral InGaP shells to reduce surface recombination. The lasers operate single-mode at room temperature with low threshold peak power density of ~625 W/cm^2. Cavity resonance and lasing wavelength is lithographically defined by controlling pillar pitch and diameter to vary from 960 to 989 nm. We envision this bottom-up approach to pillar-based devices as a new platform for photonic systems integration

Carrier localization and in-situ annealing effect on quaternary Ga1-xInxAsySb1-y/GaAs quantum wells grown by Sb pre-deposition

Using temperature-dependent photoluminescence spectroscopy, we have investigated and compared intrinsic InGaAs, intrinsic GaInAsSb, and p-i-n junction GaInAsSb quantum wells (QWs) embedded in GaAs barriers. Strong carrier localization inside the intrinsic GaInAsSb/GaAs QW has been observed together with its decrease inside the p-i-n sample. This is attributed to the effect of an in-situ annealing during the top p-doped AlGaAs layer growth at an elevated temperature of 580 degrees C, leading to Sb-atom diffusion and even atomic redistribution. High-resolution X-ray diffraction measurements and the decrease of both maximum localization energy and full delocalization temperature in the p-i-n QW sample further corroborated this conclusion. (C) 2013 American Institute of Physics. (http://dx.doi.org/10.1063/1.4795866

Strongly coupled slow-light polaritons in one-dimensional disordered localized states

Cavity quantum electrodynamics advances the coherent control of a single quantum emitter with a quantized radiation field mode, typically piecewise engineered for the highest finesse and confinement in the cavity field. This enables the possibility of strong coupling for chip-scale quantum processing, but till now is limited to few research groups that can achieve the precision and deterministic requirements for these polariton states. Here we observe for the first time coherent polariton states of strong coupled single quantum dot excitons in inherently disordered one-dimensional localized modes in slow-light photonic crystals. Large vacuum Rabi splittings up to 311 {\mu}eV are observed, one of the largest avoided crossings in the solid-state. Our tight-binding models with quantum impurities detail these strong localized polaritons, spanning different disorder strengths, complementary to model-extracted pure dephasing and incoherent pumping rates. Such disorder-induced slow-light polaritons provide a platform towards coherent control, collective interactions, and quantum information processing.Comment: 17 pages, 5 figures and supplementary informatio

Electro-optical and lasing properties of hybrid quantum dot/quantum well material system for reconfigurable photonic devices

We characterize the electro-optical and lasing properties of a hybrid material consisting of multiple InAs quantum dot (QD) layers together with an InGaAs quantum well (QW) grown on a GaAs substrate. Over 40 nm Stark shift of the InGaAs QW leading to 9 dB extinction ratio was demonstrated. Lasing operation at the QD first excited state transition of 1070 nm was achieved and together with < 10 ps absorption recovery the system shows promise for high-speed mode-locked lasers and electro-modulated lasers. (C) 2013 American Institute of Physics. (http://dx.doi.org/10.1063/1.4791565

Review Article: Molecular Beam Epitaxy of Lattice-Matched InAlAs and InGaAs Layers on InP (111)A, (111)B, and (110)

For more than 50 years, research into III–V compound semiconductors has focused almost exclusively on materials grown on (001)-oriented substrates. In part, this is due to the relative ease with which III–Vs can be grown on (001) surfaces. However, in recent years, a number of key technologies have emerged that could be realized, or vastly improved, by the ability to also grow high-quality III–Vs on (111)- or (110)-oriented substrates These applications include: next-generation field-effect transistors, novel quantum dots, entangled photon emitters, spintronics, topological insulators, and transition metal dichalcogenides. The first purpose of this paper is to present a comprehensive review of the literature concerning growth by molecular beam epitaxy (MBE) of III–Vs on (111) and (110) substrates. The second is to describe our recent experimental findings on the growth, morphology, electrical, and optical properties of layers grown on non-(001) InP wafers. Taking InP(111)A, InP(111)B, and InP(110) substrates in turn, the authors systematically discuss growth of both In0.52Al0.48As and In0.53Ga0.47As on these surfaces. For each material system, the authors identify the main challenges for growth, and the key growth parameter–property relationships, trends, and interdependencies. The authors conclude with a section summarizing the MBE conditions needed to optimize the structural, optical and electrical properties of GaAs, InAlAs and InGaAs grown with (111) and (110) orientations. In most cases, the MBE growth parameters the authors recommend will enable the reader to grow high-quality material on these increasingly important non-(001) surfaces, paving the way for exciting technological advances

Coulomb effect inhibiting spontaneous emission in charged quantum dot

We investigate the emission dynamics of InAs/GaAs quantum dots (QDs) coupled to an InGaAs quantum well in a tunnel injection scheme by means of time-resolved photoluminescence. Under high-power excitation we observe a redshift in the QD emission of the order of 20 meV. The optical transition intensity shows a complex evolution, where an initial plateau phase is followed by an increase in intensity before a single-exponential decay. We attribute this behavior to the Coulomb interactions between the carriers in a charged QD and corroborate the experimental results with both a rate equation model and self-consistent eight-band k.p calculations. (C) 2010 American Institute of Physics. (doi:10.1063/1.3484143

Energy-sensitive GaSb/AlAsSb separate absorption and multiplication avalanche photodiodes for X-Ray and gamma-ray detection

Demonstrated are antimony‐based (Sb‐based) separate absorption and multiplication avalanche photodiodes (SAM‐APDs) for X‐ray and gamma‐ray detection, which are composed of GaSb absorbers and large bandgap AlAsSb multiplication regions in order to enhance the probability of stopping high‐energy photons while drastically suppressing the minority carrier diffusion. Well‐defined X‐ray and gamma‐ray photopeaks are observed under exposure to 241Am radioactive sources, demonstrating the desirable energy‐sensitive detector performance. Spectroscopic characterizations show a significant improvement of measured energy resolution due to reduced high‐peak electric field in the absorbers and suppressed nonradiative recombination on surfaces. Additionally, the GaSb/AlAsSb SAM‐APDs clearly exhibit energy response linearity up to 59.5 keV with a minimum full‐width half‐maximum of 1.283 keV. A further analysis of the spectroscopic measurement suggests that the device performance is intrinsically limited by the noise from the readout electronics rather than that from the photodiodes. This study provides a first understanding of Sb‐based energy‐sensitive SAM‐APDs and paves the way to achieving efficient detection of high‐energy photons for X‐ray and gamma‐ray spectroscopy

Electro-optic properties of GaInAsSb/GaAs quantum well for high-speed integrated optoelectronic devices

The electro-optic properties of strained GaInAsSb/GaAs quantum wells (QWs) are investigated. A single QW p-i-n sample was grown by molecular beam epitaxy with antimony (Sb) pre-deposition technique. We numerically predict and experimentally verify a strong quantum confined Stark shift of 40 nm. We also predict a fast absorption recovery times crucial of high-speed optoelectronic devices mainly due to strong electron tunneling and thermionic emission. Predicted recovery times are corroborated by bias and temperature dependent time-resolved photoluminescence measurements indicating (<= 30 ps) recovery times. This makes GaInAsSb QW an attractive material particularly for electroabsorption modulators and saturable absorbers. (C) 2013 American Institute of Physics. (http://dx.doi.org/10.1063/1.4775371

Hybrid type-I InAs/GaAs and type-II GaSb/GaAs quantum dot structure with enhanced photoluminescence

We investigate the photoluminescence (PL) properties of a hybrid type-I InAs/GaAs and type-II GaSb/GaAs quantum dot (QD) structure grown in a GaAs matrix by molecular beam epitaxy. This hybrid QD structure exhibits more intense PL with a broader spectral range, compared with control samples that contain only InAs or GaSb QDs. This enhanced PL performance is attributed to additional electron and hole injection from the type-I InAs QDs into the adjacent type-II GaSb QDs. We confirm this mechanism using time-resolved and power-dependent PL. These hybrid QD structures show potential for high efficiency QD solar cell applications

GaSb Thermophotovoltaic Cells Grown on GaAs by Molecular Beam Epitaxy Using Interfacial Misfit Arrays

There exists a long-term need for foreign substrates on which to grow GaSb-based optoelectronic devices. We address this need by using interfacial misfit arrays to grow GaSb-based thermophotovoltaic cells directly on GaAs (001) substrates and demonstrate promising performance. We compare these cells to control devices grown on GaSb substrates to assess device properties and material quality. The room temperature dark current densities show similar characteristics for both cells on GaAs and on GaSb. Under solar simulation the cells on GaAs exhibit an open-circuit voltage of 0.121 V and a short-circuit current density of 15.5 mA/cm2. In addition, the cells on GaAs substrates maintain 10% difference in spectral response to those of the control cells over a large range of wavelengths. While the cells on GaSb substrates in general offer better performance than the cells on GaAs substrates, the cost-savings and scalability offered by GaAs substrates could potentially outweigh the reduction in performance. By further optimizing GaSb buffer growth on GaAs substrates, Sb-based compound semiconductors grown on GaAs substrates with similar performance to devices grown directly on GaSb substrates could be realized