InPCM: a network caching technique for improving the performance of TCP in wireless ad-hoc networks

We propose a novel mechanism called In-Network Packet Caching Mechanism (inPCM) to address TCP\u27s poor performance in IEEE 802.11 based multi-hop wireless networks. In particular, we address TCP\u27s inappropriate response to bursty and location dependent errors. The key concept is the use of intermediate nodes to perform packet recovery on behalf of TCP senders, similar to the well-known Snoop TCP but adapted to work over multi-hop wireless networks. We have conducted ns-2 simulation studies over a variety of network conditions and topologies. Our results confirm InPCM\u27s benefits to TCP in terms of delay and throughput. Moreover, it is immediately deployable without modifications to current protocols

Acoustic Treatment Design Scaling Methods

The primary purpose of this study is to develop improved models for the acoustic impedance of treatment panels at high frequencies, for application to subscale treatment designs. Effects that cause significant deviation of the impedance from simple geometric scaling are examined in detail, an improved high-frequency impedance model is developed, and the improved model is correlated with high-frequency impedance measurements. Only single-degree-of-freedom honeycomb sandwich resonator panels with either perforated sheet or "linear" wiremesh faceplates are considered. The objective is to understand those effects that cause the simple single-degree-of- freedom resonator panels to deviate at the higher-scaled frequency from the impedance that would be obtained at the corresponding full-scale frequency. This will allow the subscale panel to be designed to achieve a specified impedance spectrum over at least a limited range of frequencies. An advanced impedance prediction model has been developed that accounts for some of the known effects at high frequency that have previously been ignored as a small source of error for full-scale frequency ranges

Counterposition and negative phase velocity in uniformly moving dissipative materials

The Lorentz transformations of electric and magnetic fields were implemented to study (i) the refraction of linearly polarized plane waves into a half-space occupied by a uniformly moving material, and (ii) the traversal of linearly polarized Gaussian beams through a uniformly moving slab. Motion was taken to occur tangentially to the interface(s) and in the plane of incidence. The moving materials were assumed to be isotropic, homogeneous, dissipative dielectric materials from the perspective of a co-moving observer. Two different moving materials were considered: from the perspective of a co-moving observer, material A supports planewave propagation with only positive phase velocity, whereas material B supports planewave propagation with both positive and negative phase velocity, depending on the polarization state. For both materials A and B, the sense of the phase velocity and whether or not counterposition occurred, as perceived by a nonco-moving observer, could be altered by varying the observer's velocity. Furthermore, the lateral position of a beam upon propagating through a uniformly moving slab made of material A, as perceived by a nonco-moving observer, could be controlled by varying the observer's velocity. In particular, at certain velocities, the transmitted beam emerged from the slab laterally displaced in the direction opposite to the direction of incident beam. The transmittances of a uniformly moving slab made of material B were very small and the energy density of the transmitted beam was largely concentrated in the direction normal to the slab, regardless of the observer's velocity

Self-management support for chronic disease in primary care: frequency of patient self-management problems and patient reported priorities, and alignment with ultimate behavior goal selection.

BackgroundTo enable delivery of high quality patient-centered care, as well as to allow primary care health systems to allocate appropriate resources that align with patients' identified self-management problems (SM-Problems) and priorities (SM-Priorities), a practical, systematic method for assessing self-management needs and priorities is needed. In the current report, we present patient reported data generated from Connection to Health (CTH), to identify the frequency of patients' reported SM-Problems and SM-Priorities; and examine the degree of alignment between patient SM-Priorities and the ultimate Patient-Healthcare team member selected Behavioral Goal.MethodsCTH, an electronic self-management support system, was embedded into the flow of existing primary care visits in 25 primary care clinics and was used to assess patient-reported SM-Problems across 12 areas, patient identified SM-Priorities, and guide the selection of a Patient-Healthcare team member selected Behavioral Goal. SM-Problems included: BMI, diet (fruits and vegetables, salt, fat, sugar sweetened beverages), physical activity, missed medications, tobacco and alcohol use, health-related distress, general life stress, and depression symptoms. Descriptive analyses documented SM-Problems and SM-Priorities, and alignment between SM-Priorities and Goal Selection, followed by mixed models adjusting for clinic.Results446 participants with ≥ one chronic diseases (mean age 55.4 ± 12.6; 58.5% female) participated. On average, participants reported experiencing challenges in 7 out of the 12 SM-Problems areas; with the most frequent problems including: BMI, aspects of diet, and physical activity. Patient SM-Priorities were variable across the self-management areas. Patient- Healthcare team member Goal selection aligned well with patient SM-Priorities when patients prioritized weight loss or physical activity, but not in other self-management areas.ConclusionParticipants reported experiencing multiple SM-Problems. While patients show great variability in their SM-Priorities, the resulting action plan goals that patients create with their healthcare team member show a lack of diversity, with a disproportionate focus on weight loss and physical activity with missed opportunities for using goal setting to create targeted patient-centered plans focused in other SM-Priority areas. Aggregated results can assist with the identification of high frequency patient SM-Problems and SM-Priority areas, and in turn inform resource allocation to meet patient needs.Trial registrationClinicalTrials.gov ID: NCT01945918

Halo Sampling, Local Bias and Loop Corrections

We develop a new test of local bias, by constructing a locally biased halo density field from sampling the dark matter-halo distribution. Our test differs from conventional tests in that it preserves the full scatter in the bias relation and it does not rely on perturbation theory. We put forward that bias parameters obtained using a smoothing scale R can only be applied to computing the halo power spectrum at scales k ~ 1/R. Our calculations can automatically include the running of bias parameters and give vanishingly small loop corrections at low-k. Our proposal results in much better agreement of the sampling and perturbation theory results with simulations. In particular, unlike the standard interpretation of local bias in the literature, our treatment of local bias does not generate a constant power in the low-k limit. We search for extra noise in the Poisson corrected halo power spectrum at wavenumbers below its turn-over and find no evidence of significant positive noise (as predicted by the standard interpretation) while we find evidence of negative noise coming from halo exclusion for very massive halos. Using perturbation theory and our non-perturbative sampling technique we also demonstrate that nonlocal bias effects discovered recently in simulations impact the power spectrum only at the few percent level in the weakly nonlinear regime.Comment: 25 pages, 14 figures; V2: significant revision including more details about halo exclusion and low-k noise. Conclusions unchange

Lightweight Ceramics for Aeroacoustic Applications

The use of a HTP (High Temperature Performance) ceramic foam for aeroacoustic applications is investigated. HTP ceramic foam is a composition of silica and alumina fibers developed by LMMS. This foam is a lightweight high-temperature fibrous bulk material with small pore size, ultra high porosity, and good strength. It can be used as a broadband noise absorber at both room and high temperature (up to 1800 F). The investigation included an acoustic assessment as well as material development, and environmental and structural evaluations. The results show that the HTP ceramic foam provides good broadband noise absorbing capability and adequate strength when incorporating the HTP ceramic foam system into a honeycomb sandwich structure. On the other hand, the material is sensitive to Skydrol and requires further improvements. Good progress has been made in the impedance model development. A relationship between HTP foam density, flow resistance, and tortuosity will be established in the near future. Additional effort is needed to investigate the coupling effects between face sheet and HTP foam material