Assessment of Composite Delamination Self-Healing Under Cyclic Loading

Recently, the promise of self-healing materials for enhanced autonomous durability has been introduced using a micro-encapsulation technique where a polymer based healing agent is encapsulated in thin walled spheres and embedded into a base polymer along with a catalyst phase. For this study, composite skin-stiffener flange debonding specimens were manufactured from composite prepreg containing interleaf layers with a polymer based healing agent encapsulated in thin-walled spheres. Constant amplitude fatigue tests in three-point bending showed the effect of self-healing on the fatigue response of the skin-stiffener flange coupons. After the cycling that created debonding, fatigue tests were held at the mean load for 24 hours. For roughly half the specimens tested, when the cyclic loading was resumed a decrease in compliance (increase in stiffness) was observed, indicating that some healing had occurred. However, with continued cycling, the specimen compliance eventually increased to the original level before the hold, indicating that the damage had returned to its original state. As was noted in a prevoius study conducted with specimens tested under monotonically increasing loads to failure, healing achieved via the micro-encapsulation technique may be limited to the volume of healing agent available relative to the crack volume

Assessment of Composite Delamination Self-Healing Via Micro-Encapsulation

Composite skin/stringer flange debond specimens manufactured from composite prepreg containing interleaf layers with a polymer based healing agent encapsulated in thin walled spheres were tested. As a crack develops and grows in the base polymer, the spheres fracture releasing the healing agent. The agent reacts with catalyst and polymerizes healing the crack. In addition, through-thickness reinforcement, in the form of pultruded carbon z-pins were included near the flange tips to improve the resistance to debonding. Specimens were manufactured with 14 plies in the skin and 10 plies in the stiffener flange. Three-point bend tests were performed to measure the skin/stiffener debonding strength and the recovered strength after healing. The first three tests performed indicated no healing following unloading and reloading. Micrographs showed that delaminations could migrate to the top of the interleaf layer due to the asymmetric loading, and hence, bypass most of the embedded capsules. For two subsequent tests, specimens were clamped in reverse bending before reloading. In one case, healing was observed as evidenced by healing agent that leaked to the specimen edge forming a visible "scar". The residual strength measured upon reloading was 96% of the original strength indicating healing had occurred. Hence, self-healing is possible in fiber reinforced composite material under controlled conditions, i.e., given enough time and contact with pressure on the crack surfaces. The micro-encapsulation technique may prove more robust when capsule sizes can be produced that are small enough to be embedded in the matrix resin without the need for using an interleaf layer. However, in either configuration, the amount of healing that can occur may be limited to the volume of healing agent available relative to the crack volume that must be filled

Influence of Compression and Shear on the Strength of Composite Laminates with Z-Pinned Reinforcement

The influence of compression and shear loads on the strength of composite laminates with z-pins is evaluated parametrically using a 2D Finite Element Code (FLASH). Meshes were generated for three unique combinations of z-pin diameter and density. A laminated plate theory analysis was performed on several layups to determine the bi-axial stresses in the zero degree plies. These stresses, in turn, were used to determine the magnitude of the relative load steps prescribed in the FLASH analyses. Results indicated that increasing pin density was more detrimental to in-plane compression strength than increasing pin diameter. FLASH results for lamina with z-pins were consistent with the closed form results, and FLASH results without z-pins, if the initial fiber waviness due to z-pin insertion was added to the fiber waviness in the material to yield a total misalignment. Addition of 10% shear to the compression loading significantly reduced the lamina strength compared to pure compression loading. Addition of 50% shear to the compression indicated shear yielding rather than kink band formation as the likely failure mode. Two different stiffener reinforced skin configurations with z-pins, one quasi-isotropic and one orthotropic, were also analyzed. Six unique loading cases ranging from pure compression to compression plus 50% shear were analyzed assuming material fiber waviness misalignment angles of 0, 1, and 2 degrees. Compression strength decreased with increased shear loading for both configurations, with the quasi-isotropic configuration yielding lower strengths than the orthotropic configuration

Potential of known and short prokaryotic protein motifs as a basis for novel peptide-based antibacterial therapeutics: a computational survey

Short linear motifs (SLiMs) are functional stretches of protein sequence that are of crucial importance for numerous biological processes by mediating protein–protein interactions. These motifs often comprise peptides of less than 10 amino acids that modulate protein–protein interactions. While well-characterized in eukaryotic intracellular signaling, their role in prokaryotic signaling is less well-understood. We surveyed the distribution of known motifs in prokaryotic extracellular and virulence proteins across a range of bacterial species and conducted searches for novel motifs in virulence proteins. Many known motifs in virulence effector proteins mimic eukaryotic motifs and enable the pathogen to control the intracellular processes of their hosts. Novel motifs were detected by finding those that had evolved independently in three or more unrelated virulence proteins. The search returned several significantly over-represented linear motifs of which some were known motifs and others are novel candidates with potential roles in bacterial pathogenesis. A putative C-terminal G[AG].$motif found in type IV secretion system proteins was among the most significant detected. A KK$ motif that has been previously identified in a plasminogen-binding protein, was demonstrated to be enriched across a number of adhesion and lipoproteins. While there is some potential to develop peptide drugs against bacterial infection based on bacterial peptides that mimic host components, this could have unwanted effects on host signaling. Thus, novel SLiMs in virulence factors that do not mimic host components but are crucial for bacterial pathogenesis, such as the type IV secretion system, may be more useful to develop as leads for anti-microbial peptides or drugs

Combining Through-Thickness Reinforcement and Self-Healing for Improved Damage Tolerance and Durability of Composites

A study was undertaken to develop a prototype method for adding through-thickness hollow glass tubes infused with uncured resin and hardener in a carbon Z-pin through-thickness reinforcement field embedded in a composite laminate. Two types of tube insertion techniques were attempted in an effort to ensure the glass tubes survived the panel manufacturing process. A self-healing resin was chosen with a very low viscosity, two component, liquid epoxy resin system designed to be mixed at a 2-to-1 ratio of epoxy to hardener. IM7/8552 carbon epoxy double cantilever beam (DCB) specimens were cut from the hybrid Z-pin and glass tube reinforced panels and tested. In-situ injection of resin and hardener directly into glass tubes, in a staggered pattern to allow for 2-to-1 ratio mixing, resulted in partial healing of the fracture plane, but only if the injection was performed while the specimen was held at maximum load after initial fracture. Hence, there is some potential for healing delamination via resin and hardener delivered through a network of through-thickness glass tubes, but only if the tubes are connected to a reservoir where additional material may be injected as needed

Chylous effusion presenting in a 37-year-old woman with severe hypothyroidism: a case report

<p>Abstract</p> <p>Introduction</p> <p>We report what is to the best of our knowledge the second adult case of chylothorax clearly associated with severe hypothyroidism in the English-language medical literature. To the best of our knowledge, this is the first case of its kind reported without a prior history of malignancy.</p> <p>Case presentation</p> <p>A 37-year-old Hispanic woman with no reported significant past medical history initially presented with shortness of breath and inability to lose weight. She was found to have a large chylous effusion requiring chest-tube drainage, as well as severe hypothyroidism. After several weeks of thyroid hormone-replacement therapy, the formation of chylous pleural fluid in the patient greatly diminished, and the chest tube was removed. Upon long-term follow-up her minimal residual effusion remains stable on serial chest radiographs.</p> <p>Conclusion</p> <p>Although the exact pathophysiologic relation between low thyroid hormone levels and chyle formation remains to be elucidated, hypothyroidism should be a diagnostic consideration in patients with chylous effusions, especially those refractory to conventional treatments.</p

Deriving economic values for national sheep breeding objectives using a bio-economic model

peer-reviewedThe economic value of a trait in a breeding objective can be defined as the value of a unit change in an individual trait, while keeping all other traits constant and are widely used in the development of breeding objectives internationally. The objective of this study was to provide a description of the development of economic values for the pertinent traits included in the Irish national sheep breeding objectives using a whole farm system bio-economic model. A total of fourteen traits of economic importance representing maternal, lambing, production and health characteristics were calculated within a whole farm bio-economic model. The model was parameterised to represent an average Irish flock of 107 ewes with a mean lambing date in early March, stocked at 7.5 ewes per hectare and weaning 1.5 lambs per ewe joined to the ram. The economic values (units in parenthesis) calculated for maternal traits were: €39.76 for number of lambs born (per lamb), €0.12 for ewe mature weight cull value (per kg), −€0.57 for ewe mature weight maintenance value (per kg), −€0.09 for ewe mature weight replacement value (per kg) and −€0.84 for ewe replacement rate (per%). The economic values calculated for lambing traits were: €54.84 for lamb surviving at birth (per lamb), −€0.27 and −€0.30 for direct lambing difficulty in single and multiple-bearing ewes, respectively (per%); the corresponding values for maternal single and multiple lambing difficulty (per%) were −€0.25 and −€0.27, respectively. The calculated economic values for production traits were: −€0.25 for days to slaughter (per day), €3.70 for carcass Conformation (per EUROP grade) and −€0.84 for carcass fat (per fat score). The economic values for health traits were: −€0.24 for ewe lameness (per%), −€0.08 for lamb lameness (per%), −€0.25 for mastitis (per%), −€0.34 for dag score (per dag score) and −€0.08 for faecal egg count (per 50 eggs/g). Within the two Irish breeding objectives, the terminal and replacement breeding objective, the greatest emphasis was placed on production traits across both the terminal (62.56%) and replacement (41.65%) breeding objectives. The maternal and lambing traits accounted for the 34.19% and 23.45% of the emphasis within the replacement breeding objective, respectively. Results from this study will enable the implementation of new economic values within the national terminal and replacement Irish sheep breeding objectives which highlights the traits of importance for increasing overall farm profitability

From the oceans to the cloud: Opportunities and challenges for data, models, computation and workflows.

© The Author(s), 2019. This article is distributed under the terms of the Creative Commons Attribution License. The definitive version was published in Vance, T. C., Wengren, M., Burger, E., Hernandez, D., Kearns, T., Medina-Lopez, E., Merati, N., O'Brien, K., O'Neil, J., Potemrag, J. T., Signell, R. P., & Wilcox, K. From the oceans to the cloud: Opportunities and challenges for data, models, computation and workflows. Frontiers in Marine Science, 6(211), (2019), doi:10.3389/fmars.2019.00211.Advances in ocean observations and models mean increasing flows of data. Integrating observations between disciplines over spatial scales from regional to global presents challenges. Running ocean models and managing the results is computationally demanding. The rise of cloud computing presents an opportunity to rethink traditional approaches. This includes developing shared data processing workflows utilizing common, adaptable software to handle data ingest and storage, and an associated framework to manage and execute downstream modeling. Working in the cloud presents challenges: migration of legacy technologies and processes, cloud-to-cloud interoperability, and the translation of legislative and bureaucratic requirements for “on-premises” systems to the cloud. To respond to the scientific and societal needs of a fit-for-purpose ocean observing system, and to maximize the benefits of more integrated observing, research on utilizing cloud infrastructures for sharing data and models is underway. Cloud platforms and the services/APIs they provide offer new ways for scientists to observe and predict the ocean’s state. High-performance mass storage of observational data, coupled with on-demand computing to run model simulations in close proximity to the data, tools to manage workflows, and a framework to share and collaborate, enables a more flexible and adaptable observation and prediction computing architecture. Model outputs are stored in the cloud and researchers either download subsets for their interest/area or feed them into their own simulations without leaving the cloud. Expanded storage and computing capabilities make it easier to create, analyze, and distribute products derived from long-term datasets. In this paper, we provide an introduction to cloud computing, describe current uses of the cloud for management and analysis of observational data and model results, and describe workflows for running models and streaming observational data. We discuss topics that must be considered when moving to the cloud: costs, security, and organizational limitations on cloud use. Future uses of the cloud via computational sandboxes and the practicalities and considerations of using the cloud to archive data are explored. We also consider the ways in which the human elements of ocean observations are changing – the rise of a generation of researchers whose observations are likely to be made remotely rather than hands on – and how their expectations and needs drive research towards the cloud. In conclusion, visions of a future where cloud computing is ubiquitous are discussed.This is PMEL contribution 4873

A Pharmacist’s Role in a Dental Clinic: Establishing a Collaborative and Interprofessional Education Site

Background: Dental patients often have comorbidities and take multiple medications, some of which could impact their dental health and treatment.&nbsp; A pharmacist in a dental clinic can assist with the gathering, documentation and evaluation of a dental patient’s medication history as it pertains to their dental visit and overall health.&nbsp; Purpose: To develop and implement a collaborative and interprofessional education program with a pharmacist providing services in a dental school clinic.&nbsp;&nbsp;&nbsp;&nbsp; Summary: Creighton University School of Dentistry, a student-operated dental clinic located in Omaha, Nebraska, provides dental care by student dentists, faculty and staff to the surrounding community in a learning-focused environment.&nbsp; A pharmacist was incorporated into the dental clinic to create and establish an interprofessional relationship with both dental students and faculty beginning August 2014.&nbsp; Pharmacy students on an ambulatory care advanced pharmacy practice experience rotation were eventually added to the team.&nbsp; The pharmacy team provided medication therapy management services including disease state and medication counseling, medication reconciliation, identifying drug-related problems and dental implications of medications, and recommendations for prescribed medications.&nbsp; Conclusion: The pharmacy team’s presence was largely accepted by dental faculty, staff, dental students, and patients.&nbsp; Pharmacists can play an important role in a dental clinic by performing thorough health and medication histories and communicating with dental and medical providers involved in a patient’s care.&nbsp; &nbsp