Characterization of the extracellular lipase of Bacillus subtilis and its relationship to a membrane-bound lipase found in a mutant strain

Bacillus subtilis CMK33 is a mutant that is more osmotically fragile than the wild type when it is converted to the protoplast form. The protoplasts of this mutant contain a membrane-bound lipase, which is not found in protoplasts of the wild type. Hydrolysis of the membrane lipid of mutant protoplasts by the lipase is the cause of their fragility. A protein found in the wild type organism specifically inhibits the lipase (Kent, C., and Lennarz, W. J. (1972) Proc. Natl. Acad. Sci. U. S. A. 69, 2793-2797). This paper reports that cultures of both mutant and wild type cells contain an extracellular lipase which accumulates during the logarithmic phase of growth. The extracellular activity appears to be induced by a component of the growth medium. The membrane-bound lipase of the mutant has been partially purified and its properties have been compared to those of the extracellular lipase of the wild type. Their properties and sensitivity to the wild type inhibitor are similar, which suggests that the two molecules are closely related. The subcellular location of the lipase in the mutant has been investigated and compared to the location of the membrane-bound portion of the lipase inhibitor in the wild type. The lipase is located almost exclusively in the cytoplasmic membrane and not in mesosomal vesicles. In contrast, the lipase inhibitor is located in both types of membranes and is more concentrated in mesosomal vesicles. Under appropriate conditions, the appearance of new extracellular lipase activity in mutant cultures is paralleled by the loss of an equivalent amount of lipase activity from protoplasts prepared from the cells. This suggests that the membrane-bound lipase may be an intermediate in the secretion of the extracellular lipase. Because of the mutation in B. subtilis CMK33, which results in the absence of the lipase inhibitor, this intermediate can be found in protoplasts of the mutant, although it is not detectable in the wild type. Consequently, the mutant may be useful in studies of the mechanism of secretion of exoenzymes by Bacilli

Fuel-injector/air-swirl characterization

The objectives of this program are to establish an experimental data base documenting the behavior of gas turbine engine fuel injector sprays as the spray interacts with the swirling gas flow existing in the combustor dome, and to conduct an assessment of the validity of current analytical techniques for predicting fuel spray behavior. Emphasis is placed on the acquisition of data using injector/swirler components which closely resemble components currently in use in advanced aircraft gas turbine engines, conducting tests under conditions that closely simulate or closely approximate those developed in actual combustors, and conducting a well-controlled experimental effort which will comprise using a combination of low-risk experiments and experiments requiring the use of state-of-the-art diagnostic instrumentation. Analysis of the data is to be conducted using an existing, TEACH-type code which employs a stochastic analysis of the motion of the dispersed phase in the turbulent continuum flow field

Detailed state model of CaMKII activation and autophosphorylation

By combining biochemical experiments with computer modelling of biochemical reactions we elucidated some of the currently unresolved aspects of calcium-calmodulin-dependent protein kinase II (CaMKII) activation and autophosphorylation that might be relevant for its physiological function and provided a model that incorporates in detail the mechanism of CaMKII activation and autophosphorylation at T286 that is based on experimentally determined binding constants and phosphorylation rates. To this end, we developed a detailed state model of CaMKII activation and autophosphorylation based on the currently available literature, and constrained it with data from CaMKII autophosphorylation essays. Our model takes exact phosphorylation patterns of CaMKII holoenzymes into account, and is valid at physiologically relevant conditions where the concentrations of calcium and calmodulin are not saturating. Our results strongly suggest that even when bound to less than fully calcium-bound calmodulin, CaMKII is in the active state, and indicate that the autophosphorylation of T286 by an active non-phosphorylated CaMKII subunit is significantly faster than by an autophosphorylated CaMKII subunit. These results imply that CaMKII can be efficiently activated at significantly lower calcium concentrations than previously thought, which may explain how CaMKII gets activated at calcium concentrations existing at synapses in vivo. We also investigated the significance of CaMKII holoenzyme structure on CaMKII autophosphorylation and obtained estimates of previously unknown binding constants

PSD-95 Is Associated with the Postsynaptic Density and Not with the Presynaptic Membrane at Forebrain Synapses

PSD-95, a prominent protein component of the postsynaptic density (PSD) fraction from rat forebrain, has been localized by light microscopy to dendrites of hippocampal neurons (Cho et al., 1992) and to the presynaptic plexus of cerebellar basket cells (Kistner et al., 1993). Here we extend these studies to show that an affinity-purified antibody to PSD-95 labels the dendrites of most neurons in the forebrain and of a subset of neurons in the cerebellum. To confirm that PSD-95 is associated with the PSD at forebrain synapses and to clarify whether it is also associated with the presynaptic membrane, we employed immunogold electron microscopy of forebrain synaptosomes. Gold-labeled antibodies to PSD-95 labeled postsynaptic densities in both intact and lysed forebrain synaptosomes but did not label presynaptic terminals or the presynaptic membrane. The asymmetric distribution of PSD-95 at synapses contrasts with that of its homologs, disks-large and ZO-1, which are arranged symmetrically at septate and tight junctions, respectively

Opening of an interface flaw in a layered elastic half-plane under compressive loading

A static analysis is given of the problem of an elastic layer perfectly bonded, except for a frictionless interface crack, to a dissimilar elastic half-plane. The free surface of the layer is loaded by a finite pressure distribution directly over the crack. The problem is formulated using the two dimensional linear elasticity equations. Using Fourier transforms, the governing equations are converted to a pair of coupled singular integral equations. The integral equations are reduced to a set of simultaneous algebraic equations by expanding the unknown functions in a series of Jacobi polynomials and then evaluating the singular Cauchy-type integrals. The resulting equations are found to be ill-conditioned and, consequently, are solved in the least-squares sense. Results from the analysis show that, under a normal pressure distribution on the free surface of the layer and depending on the combination of geometric and material parameters, the ends of the crack can open. The resulting stresses at the crack-tips are singular, implying that crack growth is possible. The extent of the opening and the crack-top stress intensity factors depend on the width of the pressure distribution zone, the layer thickness, and the relative material properties of the layer and half-plane

Study of 42 and 85 GHz coupled cavity traveling-wave tubes for space use

Designs were formulated for four CW, millimeter wavelength traveling-wave tubes having high efficiency and long life. Three of these tubes, in the 42 to 44 GHz frequency region, develop power outputs of 100 to 300 watts with overall efficiencies of typically 45 percent. Another tube, which covers the frequency range of 84 to 86 GHz, provides a power output of 200 watts at 25 percent efficiency. The cathode current density in each design was 1A/sq cm. Each tube includes: metal-ceramic construction, periodic permanent magnet focusing, a two step velocity taper, an electron beam refocusing section, and a radiation cooled three-stage depressed collector. The electrical and mechanical design for each tube type is discussed in detail. The results of thermal and mechanical analyses are presented