82 research outputs found
Charge sensitivity of the Inductive Single-Electron Transistor
We calculate the charge sensitivity of a recently demonstrated device where
the Josephson inductance of a single Cooper-pair transistor is measured. We
find that the intrinsic limit to detector performance is set by oscillator
quantum noise. Sensitivity better than e is
possible with a high -value , or using a SQUID amplifier. The
model is compared to experiment, where charge sensitivity e and bandwidth 100 MHz are achieved.Comment: 3 page
Axially open nonradiative structures: an example of single-mode resonator based on the sample holder
The concept of nonradiative dielectric resonator is generalized in order to
include axially open configurations having rotational invariance. The resulting
additional nonradiative conditions are established for the different resonance
modes on the basis of their azimuthal modal index. An approximate chart of the
allowed dielectric and geometrical parameters for the TE011 mode is given. A
practical realization of the proposed device based on commercial fused quartz
tubes is demonstrated at millimeter wavelengths, together with simple
excitation and tuning mechanisms. The observed resonances are characterized in
their basic parameters, as well as in the field distribution by means of a
finite element method. The predictions of the theoretical analysis are well
confirmed, both in the general behaviour and in the expected quality factors.
The resulting device, in which the sample holder acts itself as single-mode
resonating element, combines an extreme ease of realization with
state-of-the-art performances. The general benefits of the proposed open
single-mode resonators are finally discussed.Comment: 18 pages, 10 figure
A photonic bandgap resonator to facilitate GHz frequency conductivity experiments in pulsed magnetic fields
We describe instrumentation designed to perform millimeter-wave conductivity
measurements in pulsed high magnetic fields at low temperatures. The main
component of this system is an entirely non-metallic microwave resonator. The
resonator utilizes periodic dielectric arrays (photonic bandgap structures) to
confine the radiation, such that the resonant modes have a high Q-factor, and
the system possesses sufficient sensitivity to measure small samples within the
duration of a magnet pulse. As well as measuring the sample conductivity to
probe orbital physics in metallic systems, this technique can detect the sample
permittivity and permeability allowing measurement of spin physics in
insulating systems. We demonstrate the system performance in pulsed magnetic
fields with both electron paramagnetic resonance experiments and conductivity
measurements of correlated electron systems.Comment: Submitted to the Review of Scientific instrument
Trace formula for dielectric cavities II: Regular, pseudo-integrable, and chaotic examples
Dielectric resonators are open systems particularly interesting due to their
wide range of applications in optics and photonics. In a recent paper [PRE,
vol. 78, 056202 (2008)] the trace formula for both the smooth and the
oscillating parts of the resonance density was proposed and checked for the
circular cavity. The present paper deals with numerous shapes which would be
integrable (square, rectangle, and ellipse), pseudo-integrable (pentagon) and
chaotic (stadium), if the cavities were closed (billiard case). A good
agreement is found between the theoretical predictions, the numerical
simulations, and experiments based on organic micro-lasers.Comment: 18 pages, 32 figure
Open nonradiative cavities as millimeter wave single-mode resonators
Open single-mode metallic cavities operating in nonradiative configurations
are proposed and demonstrated. Starting from well-known dielectric resonators,
possible nonradiative cavities have been established; their behavior on the
fundamental TE011 mode has been predicted on the basis of general
considerations. As a result, very efficient confinement properties are expected
for a wide variety of open structures having rotational invariance. Test
cavities realized having in mind practical millimeter wave constraints have
been characterized at microwave frequencies. The field distribution of some
relevant configurations has been modeled by means of a finite-element numerical
method. The obtained results confirm the expected high performances on widely
open configurations. A possible excitation of the proposed resonators
exploiting their nonradiative character is discussed, and the resulting overall
ease of realization enlightened in view of millimeter wave employments.Comment: 18 pages, 10 figures. Extended version including numerical modelings
and a theoretical appendix. Original version published on Rev. Sci. Instru
Three-Dimensional FDTD Simulation of Biomaterial Exposure to Electromagnetic Nanopulses
Ultra-wideband (UWB) electromagnetic pulses of nanosecond duration, or
nanopulses, have been recently approved by the Federal Communications
Commission for a number of various applications. They are also being explored
for applications in biotechnology and medicine. The simulation of the
propagation of a nanopulse through biological matter, previously performed
using a two-dimensional finite difference-time domain method (FDTD), has been
extended here into a full three-dimensional computation. To account for the UWB
frequency range, a geometrical resolution of the exposed sample was ,
and the dielectric properties of biological matter were accurately described in
terms of the Debye model. The results obtained from three-dimensional
computation support the previously obtained results: the electromagnetic field
inside a biological tissue depends on the incident pulse rise time and width,
with increased importance of the rise time as the conductivity increases; no
thermal effects are possible for the low pulse repetition rates, supported by
recent experiments. New results show that the dielectric sample exposed to
nanopulses behaves as a dielectric resonator. For a sample in a cuvette, we
obtained the dominant resonant frequency and the -factor of the resonator.Comment: 15 pages, 8 figure
The HEAT-SHIELD project - Perspectives from an inter-sectoral approach to occupational heat stress
Objectives: To provide perspectives from the HEAT-SHIELD project (www.heat-shield.eu): a multinational, inter-sectoral, and cross-disciplinary initiative, incorporating twenty European research institutions, as well as occupational health and industrial partners, on solutions to combat negative health and productivity effects caused by working on a warmer world. Methods: In this invited review, we focus on the theoretical and methodological advancements developed to combat occupational heat stress during the last five years of operation. Results: We outline how we created climate forecast models to incorporate humidity, wind and solar radiation to the traditional temperature-based climate projections, providing the basis for timely, policy-relevant, industry-specific and individualized information. Further, we summarise the industry-specific guidelines we developed regarding technical and biophysical cooling solutions considering effectiveness, cost, sustainability, and the practical implementation potential in outdoor and indoor settings, in addition to field-testing of selected solutions with time-motion analyses and biophysical evaluations. All recommendations were adjusted following feedback from workshops with employers, employees, safety officers, and adjacent stakeholders such as local or national health policy makers. The cross-scientific approach was also used for providing policy-relevant information based on socioeconomic analyses and identification of vulnerable regions considered to be more relevant for political actions than average continental recommendations and interventions. Discussion: From the HEAT-SHIELD experiences developed within European settings, we discuss how this inter-sectoral approach may be adopted or translated into actionable knowledge across continents where workers and societies are affected by escalating environmental temperatures.The study has received funding from the European Union’s Horizon 2020 research and innovation program under the grant agreement No 66878
Experimental and theoretical investigation of the structural, chemical, electronic, and high frequency dielectric properties of barium cadmium tantalate-based ceramics
Single-phase Ba(Cd1/3Ta2/3)O-3 powder was produced using conventional solid state reaction methods. Ba(Cd1/3Ta2/3)O-3 ceramics with 2 wt % ZnO as sintering additive sintered at 1550 degreesC exhibited a dielectric constant of similar to32 and loss tangent of 5x10(-5) at 2 GHz. X-ray diffraction and thermogravimetric measurements were used to characterize the structural and thermodynamic properties of the material. Ab initio electronic structure calculations were used to give insight into the unusual properties of Ba(Cd1/3Ta2/3)O-3, as well as a similar and more widely used material Ba(Zn1/3Ta2/3)O-3. While both compounds have a hexagonal Bravais lattice, the P321 space group of Ba(Cd1/3Ta2/3)O-3 is reduced from P (3) under bar m1 of Ba(Zn1/3Ta2/3)O-3 as a result of a distortion of oxygen away from the symmetric position between the Ta and Cd ions. Both of the compounds have a conduction band minimum and valence band maximum composed of mostly weakly itinerant Ta 5d and Zn 3d/Cd 4d levels, respectively. The covalent nature of the directional d-electron bonding in these high-Z oxides plays an important role in producing a more rigid lattice with higher melting points and enhanced phonon energies, and is suggested to play an important role in producing materials with a high dielectric constant and low microwave loss. (C) 2005 American Institute of Physics
Microwave sensor system for continuous monitoring of adhesive curing processes
A microwave sensor system has been developed for monitoring adhesive curing processes. The system provides continuous, real-time information about the curing progress without interfering with the reaction. An open-coaxial resonator is used as the sensor head, and measurements of its resonance frequency and quality factor are performed during cure to follow the reaction progress. Additionally, the system provides other interesting parameters such as reaction rate or cure time. The adhesive dielectric properties can also be computed off-line, which gives additional information about the process. The results given by the system correlate very well with conventional measurement techniques such as differential scanning calorimetry, combining accuracy and rate with simplicity and an affordable cost. © 2012 IOP Publishing Ltd.The authors thank Rut Benavente Martinez for her assistance in the DSC experiments. The contract of BG-B is financed by the Ministry of Science and Innovation of Spain, through the 'Torres Quevedo' Sub-programme, which is also co-financed by the European Social Fund (ESF). This work has been financed by the Ministry of Science and Innovation of Spain through the project MONIDIEL (TEC2008-04109).García Baños, B.; Catalá Civera, JM.; Penaranda-Foix, FL.; Canós Marín, AJ.; Sahuquillo Navarro, O. (2012). Microwave sensor system for continuous monitoring of adhesive curing processes. Measurement Science and Technology. 23(3). https://doi.org/10.1088/0957-0233/23/3/035101S233Jost, M., & Sernek, M. (2008). Shear strength development of the phenol–formaldehyde adhesive bond during cure. Wood Science and Technology, 43(1-2), 153-166. doi:10.1007/s00226-008-0217-2Costa, M. L., Botelho, E. C., Paiva, J. M. F. de, & Rezende, M. C. (2005). Characterization of cure of carbon/epoxy prepreg used in aerospace field. Materials Research, 8(3), 317-322. doi:10.1590/s1516-14392005000300016Chen, J., & Hojjati, M. (2007). Microdielectric analysis and curing kinetics of an epoxy resin system. Polymer Engineering & Science, 47(2), 150-158. doi:10.1002/pen.20687Sernek, M., & Kamke, F. A. (2007). Application of dielectric analysis for monitoring the cure process of phenol formaldehyde adhesive. International Journal of Adhesion and Adhesives, 27(7), 562-567. doi:10.1016/j.ijadhadh.2006.10.004Núñez, L., Gómez-Barreiro, S., Gracia-Fernández, C. A., & Núñez, M. R. (2004). Use of the dielectric analysis to complement previous thermoanalytical studies on the system diglycidyl ether of bisphenol A/1,2 diamine cyclohexane. Polymer, 45(4), 1167-1175. doi:10.1016/j.polymer.2003.12.024Lefebvre, D. R., Han, J., Lipari, J. M., Long, M. A., McSwain, R. L., & Wells, H. C. (2006). Dielectric analysis for in-situ monitoring of gelatin renaturation and crosslinking. Journal of Applied Polymer Science, 101(5), 2765-2775. doi:10.1002/app.21631Cordovez, M., Li, Y., & Karbhari, V. M. (2004). Assessment of Dielectrometry for Characterization of Processing and Moisture Absorption in FRP Composites. Journal of Reinforced Plastics and Composites, 23(4), 445-456. doi:10.1177/0731684404031980Das, N. K., Voda, S. M., & Pozar, D. M. (1987). Two Methods for the Measurement of Substrate Dielectric Constant. IEEE Transactions on Microwave Theory and Techniques, 35(7), 636-642. doi:10.1109/tmtt.1987.1133722Fioretto, D., Livi, A., Rolla, P. A., Socino, G., & Verdini, L. (1994). The dynamics of poly(n-butyl acrylate) above the glass transition. Journal of Physics: Condensed Matter, 6(28), 5295-5302. doi:10.1088/0953-8984/6/28/007Givot, B. L., Krupka, J., & Belete, D. Y. (s. f.). Split post dielectric resonator technique for dielectric cure monitoring of structural adhesives. 13th International Conference on Microwaves, Radar and Wireless Communications. MIKON - 2000. Conference Proceedings (IEEE Cat. No.00EX428). doi:10.1109/mikon.2000.913931Canos, A. J., Catala-Civera, J. M., Penaranda-Foix, F. L., & Reyes-Davo, E. (2006). A novel technique for deembedding the unloaded resonance frequency from measurements of microwave cavities. IEEE Transactions on Microwave Theory and Techniques, 54(8), 3407-3416. doi:10.1109/tmtt.2006.877833Marks, R. B., & Williams, D. F. (1992). A general waveguide circuit theory. Journal of Research of the National Institute of Standards and Technology, 97(5), 533. doi:10.6028/jres.097.024Harrington, R. F. (1967). Matrix methods for field problems. Proceedings of the IEEE, 55(2), 136-149. doi:10.1109/proc.1967.5433Baker-Jarvis, J., Janezic, M. D., Domich, P. D., & Geyer, R. G. (1994). Analysis of an open-ended coaxial probe with lift-off for nondestructive testing. IEEE Transactions on Instrumentation and Measurement, 43(5), 711-718. doi:10.1109/19.328897Taylor, B. N. (1994). Guidelines for evaluating and expressing the uncertainty of NIST measurement results. doi:10.6028/nist.tn.1297Casalini, R., Corezzi, S., Livi, A., Levita, G., & Rolla, P. A. (1997). Dielectric parameters to monitor the crosslink of epoxy resins. Journal of Applied Polymer Science, 65(1), 17-25. doi:10.1002/(sici)1097-4628(19970705)65:13.0.co;2-tPreu, H., & Mengel, M. (2007). Experimental and theoretical study of a fast curing adhesive. International Journal of Adhesion and Adhesives, 27(4), 330-337. doi:10.1016/j.ijadhadh.2006.06.004Harper, D. P., Wolcott, M. P., & Rials, T. G. (2001). Evaluation of the cure kinetics of the wood/pMDI bondline. International Journal of Adhesion and Adhesives, 21(2), 137-144. doi:10.1016/s0143-7496(00)00045-2Garcia-Banos, B., Canos, A. J., Penaranda-Foix, F. L., & Catala-Civera, J. M. (2011). Noninvasive Monitoring of Polymer Curing Reactions by Dielectrometry. IEEE Sensors Journal, 11(1), 62-70. doi:10.1109/jsen.2010.2050475He, Y. (2001). DSC and DEA studies of underfill curing kinetics. Thermochimica Acta, 367-368, 101-106. doi:10.1016/s0040-6031(00)00654-7Núñez-Regueira, L., Gracia-Fernández, C. A., & Gómez-Barreiro, S. (2005). Use of rheology, dielectric analysis and differential scanning calorimetry for gel time determination of a thermoset. Polymer, 46(16), 5979-5985. doi:10.1016/j.polymer.2005.05.06
- …