112 research outputs found
The cyan-green luminescent behaviour of nitrided Ba9Y2Si6O24: Eu2+ phosphors for W-LED
The nitrided Ba9Y2Si6O24: Eu2+ phosphors were prepared by the conventional high temperature solid state reaction. Si3N4 doping obviously improves the luminescent intensity compared with undoped phosphors. The Eu2+ emitting lights in different Ba2+ crystal lattices and its temperature dependent luminescence properties from 293 to 453 K are discussed. Under the 410 nm excitation, the nitrided Ba9Y2Si6O24:Eu2+ has more thermal stability than other same crystal structure of Ba9M2Si6O24:Eu2+ (M = Sc, Lu, Y). The nitriding schemes can significantly improve the luminescence properties of the phosphors, and nitrided Ba9Y2Si6O24: Eu2+ can be an excellent candidate as a green phosphor for W-LEDs
Structure and properties of composite Ni–Co–Mn coatings on metal interconnects by electrodeposition
In order to obtain the high conductivity values and wide spinel stability region for solid oxide fuel cell interconnect, several multilayer Ni, Co and Mn coatings are electroplated and then oxidized in air to form spinel oxide layers. Potentiodynamic polarization curves in different simple solutions are tested to analyze the deposition behavior of Co and Mn. Microstructures and compositions of Ni–Co–Mn multi-layers by adjusting the thickness and deposition parameters are analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that area specific resistance value of sample B–Ni/Co after oxidation at 750 °C for 500h is the lowest among the coatings, and the resistance values at 700 °C and 800 °C are 35.3 and 31.7 mΩ‧cm2, respectively. When the Ni transition layer in the vicinity of coating/substrate interface is thick, it will lead to the outward diffusion and aggregation of element Fe to form Fe-rich oxide intermediate layer, which will affect the high-temperature performance of the coating. Pure Co and CoMn alloy coatings with a certain thickness can effectively prevent the inward diffusion of oxygen and the outward diffusion of Fe and Cr at high temperature. The thin Ni transition layer combined with the thick Co layer or CoMn layer has the best element diffusion inhibition and high temperature electrical properties during the long-term high-temperature oxidation process
Regio- and stereoselective organocatalyzed relay glycosylations to synthesize 2-amino-2-deoxy-1,3-dithioglycosides
Herein, we describe a novel methodology for the regio-and stereoselectiveconvergent synthesis of 2-amino-2-deoxy-dithioglycosides via one-potrelay glycosylation of 3-O-acetyl-2-nitroglucal donors.This unique organo-catalysis relay glycosylation features excellentsite- and stereoselectivity, good to excellent yields, mild reactionconditions, and broad substrate scope. 2-Amino-2-deoxy-glucosides/mannosidesbearing 1,3-dithio-linkages were efficiently obtained from 3-O-acetyl-2-nitroglucal donors in both stepwise and one-potglycosylation protocols. The dithiolated O-antigen of E. coli serogroup 64 was successfully synthesizedusing this newly developed method.Bio-organic Synthesi
Existence of a continental-scale river system in eastern Tibet during the late Cretaceous–early Palaeogene
The establishment of continental-scale drainage systems on Earth is largely controlled by topography related to plate boundary deformation and buoyant mantle. Drainage patterns of the great rivers in Asia are thought to be highly dynamic during the Cenozoic collision of India and Eurasia, but the drainage pattern and landscape evolution prior to the development of high topography in eastern Tibet remain largely unknown. Here we report the results of petro-stratigraphy, heavy-mineral analysis, and detrital zircon U-Pb dating from late Cretaceous–early Palaeogene sedimentary basin strata along the present-day eastern margin of the Tibetan Plateau. Similarities in the provenance signatures among basins indicate that a continental-scale fluvial system once drained southward into the Neo-Tethyan Ocean. These results challenge existing models of drainage networks that flowed toward the East Asian marginal seas and require revisions to inference of palaeo-topography during the Late Cretaceous. The presence of a continent-scale river may have provided a stable long-term base level which, in turn, facilitated the development of an extensive low-relief landscape that is preserved atop interfluves above the deeply incised canyons of eastern Tibet
Measurement of Cosmic-ray Muon-induced Spallation Neutrons in the Aberdeen Tunnel Underground Laboratory
AbstractMuon-induced neutrons are one of the major backgrounds to various underground experiments, such as dark matter searches, low-energy neutrino oscillation experiments and neutrino-less double beta-decay experiments. Previous experiments on the underground production rate of muon-induced neutrons were mostly carried out either at shallow sites or at very deep sites. The Aberdeen Tunnel experiment aims to measure the neutron production rate at a moderate depth of 611 meters water equivalent. Our apparatus comprises of six layers of plastic-scintillator hodoscopes for tracking the incident cosmic-ray muons, and 760 L of gadolinium-doped liquid-scintillator for both neutron production and detection targets. In this paper, we describe the design and the performance of the apparatus. The preliminary result on the measurement of neutron production rate is also presented
A study of fast and metastable dissociations of adenine-thymine binary-base oligonucleotides by using positive-ion MALDI-TOF mass spectrometry
Towards a dynamic photosynthesis model to guide yield improvement in C4 crops
The most productive C4 food and biofuel crops, such as Saccharum officinarum (sugarcane), Sorghum bicolor (sorghum) and Zea mays (maize), all use NADP-ME-type C4 photosynthesis. Despite high productivities, these crops fall well short of the theoretical maximum solar conversion efficiency of 6%. Understanding the basis of these inefficiencies is key for bioengineering and breeding strategies to increase the sustainable productivity of these major C4 crops. Photosynthesis is studied predominantly at steady state in saturating light. In field stands of these crops light is continually changing, and often with rapid fluctuations. Although light may change in a second, the adjustment of photosynthesis may take many minutes, leading to inefficiencies. We measured the rates of CO2 uptake and stomatal conductance of maize, sorghum and sugarcane under fluctuating light regimes. The gas exchange results were combined with a new dynamic photosynthesis model to infer the limiting factors under non-steady-state conditions. The dynamic photosynthesis model was developed from an existing C4 metabolic model for maize and extended to include: (i) post-translational regulation of key photosynthetic enzymes and their temperature responses; (ii) dynamic stomatal conductance; and (iii) leaf energy balance. Testing the model outputs against measured rates of leaf CO2 uptake and stomatal conductance in the three C4 crops indicated that Rubisco activase, the pyruvate phosphate dikinase regulatory protein and stomatal conductance are the major limitations to the efficiency of NADP-ME-type C4 photosynthesis during dark-to-high light transitions. We propose that the level of influence of these limiting factors make them targets for bioengineering the improved photosynthetic efficiency of these key crops. © 2021 The Authors. The Plant Journal published by Society for Experimental Biology and John Wiley & Sons Ltd
Synthesis, self-assembly, disassembly, and reassembly of two types of Cu2O nanocrystals unifaceted with {001} or {110} planes
10.1021/ja100151fJournal of the American Chemical Society132176131-6144JACS
Research on Prediction Model of Conical Pick Cutting Force Based on Coulomb-Mohr Criterion
Cutting force is one of the most important influence factors that affect the efficiency and service life of the conical pick. In order to accurately calculate the cutting force, through theoretical analysis and experimental research, a cutting force model consisted of the basic fracture parameters of rock, geometric parameters and installation parameters of pick is proposed based on the coulomb-mohr criterion, and the calculation model is corrected by whole cutting experimental data, and validated the corrected model by orthogonal test, the result show that the error of the cutting force model is about 10%, which meets the requirements of engineering data. At the same time, significant analysis on the cutting force is obtained by range method, cutting depth h > semi-tip angle β > cutting angle α
- …