Sensitive bridge circuit measures conductance of low-conductivity electrolyte solutions

Compact bridge circuit measures sensitive and accurate conductance of low-conductivity electrolyte solutions. The bridge utilizes a phase sensitive detector to obtain a linear deflection of the null indicator relative to the measured conductance

Improved channel multiplier for radiation-and-particle detectors

Multiplier is formed of glass and includes cylindrically-shaped main channel element having length-to-diameter ratio of 50 to 1. Element has open slot along its length. Attached to slot edges are two glass plates set at an angle to each other. Inside surfaces are coated with secondary electron emissive coating

Evaluation of decay curves of a chemical species undergoing simultaneous first- and second-order decay

IBM 1620 computer prepares tables to enable fast calculation of the first- and second-order rate constants from two half-lives and the corresponding initial concentrations, obtained from either one or two decay curves

Radiation and particle detector and amplifier

A radiation or charged particle detector is described which incorporates a channel multiplier structure to amplify the detected rays or particles. The channel multiplier structure has a support multiplying element with a longitudinal slot along one side. The element supports a pair of plates positioned contiguous with the slot. The plates funnel the particles or rays to be detected into the slotted aperture and the element, thus creating an effectively wide aperture detector of the windowless type

GEOS-20 m cable boom mechanism

The GEOS cable boom mechanism allows the controlled deployment of a 20 m long cable in a centrifugal force field. In launch configuration the flat cable is reeled on a 240 mm diameter drum. The electrical connection between the rotating drum and the stationary housing is accomplished via a flexlead positioned inside the drum. Active motion control of this drum is achieved by a self locking worm gear, driven by a stepper motor. The deployment length of the cable is monitored by an optical length indicator, sensing black bars engraved on the cable surface

Pilot modeling, modal analysis, and control of large flexible aircraft

The issues to be addressed are threefold. The first deals with the question of whether dynamic aeroelastic effects can significantly impact piloted flight dynamics. For example, if one were to explore this problem experimentally, what mathematical model would be appropriate to use in the simulation? What modes, for example, should be included in the simulation, or what linear model should be used in the control synthesis? The second question deals with the appropriate design criteria or design objectives. In the case of active control, for example, what would be the design objectives for the control synthesis if aeroelastic effects are a problem? The outline of the topics includes a description of a model analysis methodology aimed at answering the question of the significance of higher order dynamics. Secondly, a pilot vehicle analysis of some experimental data addresses the question of ""What's important in the task?'' The experimental data will be presented briefly, followed by the results of an open-loop modal analysis of the generic vehicle configurations in question. Finally, one of the vehicles will be augmented via active control and the results presented

GEOS axial booms

A booms and mechanisms subsystem was designed, developed, and qualified for the geostationary scientific satellite GEOS. Part of this subsystem consist of four axial booms consisting of one pair of 1 m booms and one pair of 2.5 m booms. Each of these booms is carrying one bird cage electric field sensor. Alignment accuracy requirements led to a telescopic type solution. Deployment is performed by pressurized nitrogen. At deployment in orbit two of these booms showed some anomalies and one of these two deployed only about 80%. Following this malfunction a detailed failure investigation was performed resulting in a design modification of some critical components as release mechanism, guide sleeves of the telescopic elements, and pressure system

Multivariable frequency weighted model order reduction for control synthesis

Quantitative criteria are presented for model simplification, or order reduction, such that the reduced order model may be used to synthesize and evaluate a control law, and the stability robustness obtained using the reduced order model will be preserved when controlling the full-order system. The error introduced due to model simplification is treated as modeling uncertainty, and some of the results from multivariate robustness theory are brought to bear on the model simplification problem. A numerical procedure developed previously is shown to lead to results that meet the necessary criteria. The procedure is applied to reduce the model of a flexible aircraft. Also, the importance of the control law itself, in meeting the modeling criteria, is underscored. An example is included that demonstrates that an apparently robust control law actually amplifies modest modeling errors in the critical frequency region, and leads to undesirable results. The cause of this problem is associated with the canceling of lightly damped transmission zeroes in the plant. An attempt is made to expand on some of the earlier results and to further clarify the theoretical basis behind the proposed methodology