2,665 research outputs found
Spectral characterization of the LANDSAT Thematic Mapper sensors
The spectral coverage characteristics of the two thematic mapper instruments were determined by analyses of spectral measurements of the optics, filters, and detectors. The following results are presented: (1) band 2 and 3 flatness was slightly below specification, and band 7 flatness was below specification; (2) band 5 upper-band edge was higher than specifications; (3) band 2 band edges were shifted upward about 9 nm relative to nominal; and (4) band 4, 5, and 7 lower band edges were 16 to 18 nm higher then nominal
Spectral characterization of the LANDSAT-D multispectral scanner subsystems
Relative spectral response data for the multispectral scanner subsystems (MSS) to be flown on LANDSAT-D and LANDSAT-D backup, the protoflight and flight models, respectively, are presented and compared to similar data for the Landsat 1,2, and 3 subsystems. Channel-bychannel (six channels per band) outputs for soil and soybean targets were simulated and compared within each band and between scanners. The two LANDSAT-D scanners proved to be nearly identical in mean spectral response, but they exhibited some differences from the previous MSS's. Principal differences between the spectral responses of the D-scanners and previous scanners were: (1) a mean upper-band edge in the green band of 606 nm compared to previous means of 593 to 598 nm; (2) an average upper-band edge of 697 nm in the red band compared to previous averages of 701 to 710 nm; and (3) an average bandpass for the first near-IR band of 702-814 nm compared to a range of 693-793 to 697-802 nm for previous scanners. These differences caused the simulated D-scanner outputs to be 3 to 10 percent lower in the red band and 3 to 11 percent higher in the first near-IR band than previous scanners for the soybeans target. Otherwise, outputs from soil and soybean targets were only slightly affected. The D-scanners were generally more uniform from channel to channel within bands than previous scanners
Introduction to Thematic Mapper investigations. Section 1: Radiometry. Section 2: Geometry
An overview of papers which deal with radiometric characterization of the TM sensor is presented. Spectral characteristics are summarized. The geometric accuracy of TM are also examined. Aspects of prelaunch and post launch sensor performance, ground processing techniques, and error correction are also investigated
Local flow management/profile descent algorithm. Fuel-efficient, time-controlled profiles for the NASA TSRV airplane
The Local Flow Management/Profile Descent (LFM/PD) algorithm designed for the NASA Transport System Research Vehicle program is described. The algorithm provides fuel-efficient altitude and airspeed profiles consistent with ATC restrictions in a time-based metering environment over a fixed ground track. The model design constraints include accommodation of both published profile descent procedures and unpublished profile descents, incorporation of fuel efficiency as a flight profile criterion, operation within the performance capabilities of the Boeing 737-100 airplane with JT8D-7 engines, and conformity to standard air traffic navigation and control procedures. Holding and path stretching capabilities are included for long delay situations
An investigation of TNAV equipped aircraft in a simulated en route metering environment
This document presents the results of an effort to estimate how often a TNAV (Time Navigation) equipped aircraft could be given a TNAV clearance in the En Route Metering (ERM) system as a function of the percentage of arriving traffic which is TNAV equipped. A fast-time simulation of Denver Stapleton international arrival traffic in the Denver Air Route Traffic Control Center route structure, including en route metering operations, was used to develop data on estimated conflicts, clearance communications and fuel usage for traffic mixes of 25, 50, 75 and 100% TNAV equipped. This study supports an overall effort by NASA to assess the benefits and required technology for using TNAV-equipped aircraft in the ERM environment
Full stress tensor measurement using colour centres in diamond
Stress and strain are important factors in determining the mechanical,
electronic, and optical properties of materials, relating to each other by the
material's elasticity or stiffness. Both are represented by second rank field
tensors with, in general, six independent components. Measurements of these
quantities are usually achieved by measuring a property that depends on the
translational symmetry and periodicity of the crystal lattice, such as optical
phonon energies using Raman spectroscopy, the electronic band gap using
cathodoluminescence, photoelasticity via the optical birefringence, or Electron
Back Scattering Diffraction (EBSD). A reciprocal relationship therefore exists
between the maximum sensitivity of the measurements and the spatial resolution.
Furthermore, of these techniques, only EBSD and off-axis Raman spectroscopy
allow measurement of all six components of the stress tensor, but neither is
able to provide full 3D maps. Here we demonstrate a method for measuring the
full stress tensor in diamond, using the spectral and optical polarization
properties of the photoluminescence from individual nitrogen vacancy (NV)
colour centres. We demonstrate a sensitivity of order 10 MPa, limited by local
fluctuations in the stress in the sample, and corresponding to a strain of
about 10^-5, comparable with the best sensitivity provided by other techniques.
By using the colour centres as built-in local sensors, the technique overcomes
the reciprocal relationship between spatial resolution and sensitivity and
offers the potential for measuring strains as small as 10^-9 at spatial
resolution of order 10 nm. Furthermore it provides a straightforward route to
volumetric stress mapping. Aside from its value in understanding strain
distributions in diamond, this new approach to stress and strain measurement
could be adapted for use in micro or nanoscale sensors.Comment: 12 pages, 5 figures - supplementary informations included in appendi
Making the Connection: Using Mobile Devices and PollEverywhere for Experiential Learning for Adult Students
Technology integration has significantly influenced the way students access and retain knowledge gained in the classroom (Ahmed, 2016). This is particularly relevant in classrooms for adult learners who engage in continuing education. This paper used a descriptive case study (Yin, 2014) to share how an instructor utilized mobile learning with a web-based polling tool, PollEverywhere, to gamify experiential learning for adult students in various roles within a southeastern state’s court administration—prosecutors, defense lawyers, magistrates, and jail administrators—and improve students’ engagement in the course and connection to course material
Thermal Studies on Rubidium Dinitramide
The present study has been carried out to investigate conflicting reports in the literature on the nature of the thermal decomposition of the energetic oxidant rubidium dinitramide in the liquid state. The techniques employed included DSC, simultaneous TG-DTA, simultaneous TG-mass spectrometry and thermomicroscopy. The measurements were supplemented by quantitative chemical analysis of the reaction products. The results showed that, following fusion at 106 °C, the overall decomposition proceeded in a single exothermic reaction stage forming a mixture of rubidium nitrate and rubidium nitrite in the molar ratio 1.2 : 1
Properties of implanted and CVD incorporated nitrogen-vacancy centers: preferential charge state and preferential orientation
The combination of the long electron state spin coherence time and the optical coupling of the ground electronic states to an excited state manifold makes the nitrogen-vacancy (NV) center in diamond an attractive candidate for quantum information processing. To date the best spin and optical properties have been found in centers deep within the diamond crystal. For useful devices it will be necessary to engineer NVs with similar properties close to the diamond surface. We report on properties including charge state control and preferential orientation for near surface NVs formed either in CVD growth or through implantation and annealing
Deterministic delivery of remote entanglement on a quantum network
Large-scale quantum networks promise to enable secure communication,
distributed quantum computing, enhanced sensing and fundamental tests of
quantum mechanics through the distribution of entanglement across nodes. Moving
beyond current two-node networks requires the rate of entanglement generation
between nodes to exceed their decoherence rates. Beyond this critical
threshold, intrinsically probabilistic entangling protocols can be subsumed
into a powerful building block that deterministically provides remote entangled
links at pre-specified times. Here we surpass this threshold using diamond spin
qubit nodes separated by 2 metres. We realise a fully heralded single-photon
entanglement protocol that achieves entangling rates up to 39 Hz, three orders
of magnitude higher than previously demonstrated two-photon protocols on this
platform. At the same time, we suppress the decoherence rate of remote
entangled states to 5 Hz by dynamical decoupling. By combining these results
with efficient charge-state control and mitigation of spectral diffusion, we
are able to deterministically deliver a fresh remote state with average
entanglement fidelity exceeding 0.5 at every clock cycle of 100 ms
without any pre- or post-selection. These results demonstrate a key building
block for extended quantum networks and open the door to entanglement
distribution across multiple remote nodes.Comment: v2 - updated to include relevant citatio
- …