522 research outputs found
End Mass Effects on the Frequency Response of Cantilevers: Analytical Results
International audienc
Resonant Microcantilevers for the Determination of the Loss Modulus of Thin Polymer Films
The increasing interest in polymer materials creates the need for accurate tools to characterize their mechanical properties. Due to energy dissipation in polymers during deformation, these materials exhibit viscoelastic behavior. Accurate determination of these viscoelastic properties and, more specifically, viscous losses, remains challenging and mainly unknown for thin polymer films. In this paper, a straightforward method to determine the loss modulus of organic materials using resonating microcantilevers has been developed. The extracted results for polyisobutylene show the variation of viscous losses over a large range of frequencies (7-350 kHz)
Description of the unsteady flow pattern from peak efficiency to near surge in subsonic centrifugal compressor stage
This paper aims to describe the flow structure modifications when the operating point moves from peak efficiency to near stall condition in a moderate pressure ratio centrifugal compressor stage consisted of a splittered unshrouded impeller and a vaned diffuser. The investigations are based on three-dimensional U-RANS simulation results. The flow is described in the impeller and in the vaned diffuser through time-averaged flow quantities and unsteady fluctuations. Results show that at low mass flow rate, the effects of secondary flow in the impeller are more pronounced, inducing both, high time-averaged values and temporal fluctuations of the flow angle near the shroud at the diffuser inlet, leading to vane suction side boundary layer separation. Pressure waves due to impeller diffuser interaction spread through the vaned diffuser generating unsteadiness which intensifies at near surge condition
Generalized Model of Resonant Polymer-Coated Microcantilevers in Viscous Liquid Media
Expressions describing the resonant frequency and quality factor of a dynamically driven, polymer-coated microcantilever in a viscous liquid medium have been obtained. These generalized formulas are used to describe the effects the operational medium and the viscoelastic coating have on the device sensitivity when used in liquid-phase chemical sensing applications. Shifts in the resonant frequency are normally assumed proportional to the mass of sorbed analyte in the sensing layer. However, the expression for the frequency shift derived in this work indicates that the frequency shift is also dependent on changes in the sensing layer’s loss and storage moduli, changes in the moment of inertia, and changes in the medium of operation’s viscosity and density. Not accounting for these factors will lead to incorrect analyte concentration predictions. The derived expressions are shown to reduce to well-known formulas found in the literature for the case of an uncoated cantilever in a viscous liquid medium and the case of a coated cantilever in air or in a vacuum. The theoretical results presented are then compared to available chemical sensor data in aqueous and viscous solutions
A Multi-Modal Continuous-Systems Model of a Novel High-Q Disk Resonator in a Viscous Liquid
International audienc
L'implémentation des recommandations basées sur des preuves (EBN) dans un contexte de soins aigus: prévention des escarres : revue de littérature étoffée
Une abondante littérature traite de la prévention des escarres, cependant leur survenue reste encore trop élevée et cela engendre des coûts importants et des conséquences délétères pour le patient. Il existe un fossé important entre la théorie et la pratique concernant la prévention des escarres en milieu hospitalier. Les preuves issues de recherches scientifiques ne sont pas toujours appliquées par les infirmières dans les milieux de soins aigus. Ce travail a pour but d’identifier les facteurs ayant une influence sur l’application des recommandations basées sur des preuves et de donner des pistes afin d’augmenter l’intérêt des infirmières pour la recherche
Development of Analytical Models of T- and U-shaped Cantilever-based MEMS Devices for Sensing and Energy Harvesting Applications
Dynamic-mode cantilever-based structures supporting end masses are frequently used as MEMS/NEMS devices in application areas as diverse as chemical/biosensing, atomic force microscopy, and energy harvesting. This paper presents a new analytical solution for the free vibration of a cantilever with a rigid end mass of finite size. The effects of both translational and rotational inertia as well as horizontal eccentricity of the end mass are incorporated into the model. This model is general regarding the end-mass distribution/geometry and is validated here for the commonly encountered geometries of T- and U-shaped cantilevers. Comparisons with 3D FEA simulations and experiments on silicon and organic MEMS are quite encouraging. The new solution gives insight into device behavior, provides an efficient tool for preliminary design, and may be extended in a straightforward manner to account for inherent energy dissipation in the case of organic-based cantilevers
Resonant Characteristics of Rectangular Microcantilevers Vibrating Torsionally in Viscous Liquid Media
The resonant characteristics of rectangular microcantilevers vibrating in the torsional mode in viscous liquid media are investigated. The hydrodynamic load (torque per unit length) on the vibrating beam due to the liquid was first determined using a finite element model. An analytical expression of the hydrodynamic function in terms of the Reynolds number and aspect ratio, h/b (with thickness, h, and width, b) was then obtained by fitting the numerical results. This allowed for the resonance frequency and quality factor to be investigated as functions of both beam geometry and medium properties. Moreover, the effects of the aspect ratio on the cross-section\u27s torsional constant, K, which affects the microcantilever\u27s torsional stiffness, and on its polar moment of inertia, Jp, which is associated with the beam\u27s rotational inertia, are also considered when obtaining the resonance frequency and quality factor. Compared with microcantilevers under out-of-plane (transverse) flexural vibration, the results show that microcantilevers that vibrate in their 1st torsional or 1st in-plane (lateral) flexural resonant modes have higher resonance frequency and quality factor. The increase in resonance frequency and quality factor results in higher mass sensitivity and reduced frequency noise, respectively. The improvement in the sensitivity and quality factor are expected to yield much lower limits of detection in liquid-phase chemical sensing applications
- …