1,384 research outputs found
Comparison of acoustic and strain gauge techniques for crack closure measurements
A quantitative study on the systems performances of the COD gauge and the acoustic transmission techniques to elastic deformation of part-through crack and compact tension specimens has been conducted. It is shown that the two instruments measure two completely different quantities: The COD gauge yields information on the length change of the specimen whereas the acoustic technique is sensitive directly to the amount of contract area between two surfaces, interfering with the acoustic signal. In another series of experiments, compression tests on parts with specifically prepared surfaces were performed so that the surface contact area could be correlated with the transmitted acoustic signal, as well as the acoustic with the COD gauge signal. A linear relation between contact area and COD gauge signal was obtained until full contact had been established
Surface Wave Techniques for Predicting the Remaining Life of Fatigue Damaged Metals
In our continuing efforts to investigate methods to characterize the state of fatigue nondestructively and to apply these observations to lifetime predictions, we have initiated acoustic surface wave studies using Al 2024-T351. A smooth bar specimen was designed which can be tested in tension-compression fatigue. Acoustic wedge transducers were mounted on the specimen to sample fatigue induced changes within the gauge section. Data on acoustic harmonic generation were taken as a function of applied external load at any point of the sample\u27s fatigue life. An optical microscope was attached to the load frame to monitor microcrack formation in the gauge section. Significant changes of the second harmonic have been observed as a function of stress and fatigue. First results indicate a decrease of the second harmonic as a function of stress. At about 50% of the fatigue life microcracks initiated at surface intermetallics and a substantial increase of the second harmonic amplitude in the vicinity of zero external applied load was observed
Micromechanics of fatigue in woven and stitched composites
The goal is to determine how microstructural factors, especially the architecture of microstructural factors, control fatigue damage in 3D reinforced polymer composites. Test materials were fabricated from various preforms, including stitched quasi-isotropic laminates, and through-the-thickness angle interlock, layer-to-layer angle interlock, and through-the-thickness stitching effect weaves. Preforms were impregnated with a tough resin by a special vacuum infiltration method. Most tests are being performed in uniaxial compression/compression loading. In all cases to date, failure has occurred not by delamination, but by shear failure, which occurs suddenly rather than by gradual macroscopic crack growth. Some theoretical aspects of bridging are also examined
Adaptive Variable Bias Magnetic Bearing Control
Most magnetic bearing control schemes use a bias current with a superimposed control current to linearize the relationship between the control current and the force it delivers. With the existence of the bias current, even in no load conditions, there is always some power consumption. In aerospace applications, power consumption becomes an important concern. In response to this concern, an alternative magnetic bearing control method, called Adaptive Variable Bias Control (AVBC), has been developed and its performance examined. The AVBC operates primarily as a proportional-derivative controller with a relatively slow, bias current dependent, time-varying gain. The AVBC is shown to reduce electrical power loss, be nominally stable, and provide control performance similar to conventional bias control. Analytical, computer simulation, and experimental results are presented in this paper
Theoretical investigation of finite size effects at DNA melting
We investigated how the finiteness of the length of the sequence affects the
phase transition that takes place at DNA melting temperature. For this purpose,
we modified the Transfer Integral method to adapt it to the calculation of both
extensive (partition function, entropy, specific heat, etc) and non-extensive
(order parameter and correlation length) thermodynamic quantities of finite
sequences with open boundary conditions, and applied the modified procedure to
two different dynamical models. We showed that rounding of the transition
clearly takes place when the length of the sequence is decreased. We also
performed a finite-size scaling analysis of the two models and showed that the
singular part of the free energy can indeed be expressed in terms of an
homogeneous function. However, both the correlation length and the average
separation between paired bases diverge at the melting transition, so that it
is no longer clear to which of these two quantities the length of the system
should be compared. Moreover, Josephson's identity is satisfied for none of the
investigated models, so that the derivation of the characteristic exponents
which appear, for example, in the expression of the specific heat, requires
some care
Properties of pedestrians walking in line: Stepping behavior
In human crowds, interactions among individuals give rise to a variety of
self-organized collective motions that help the group to effectively solve the
problem of coordination. However, it is still not known exactly how humans
adjust their behavior locally, nor what are the direct consequences on the
emergent organization. One of the underlying mechanisms of adjusting individual
motions is the stepping dynamics. In this paper, we present first quantitative
analysis on the stepping behavior in a one-dimensional pedestrian flow studied
under controlled laboratory conditions. We find that the step length is
proportional to the velocity of the pedestrian, and is directly related to the
space available in front of him, while the variations of the step duration are
much smaller. This is in contrast with locomotion studies performed on isolated
pedestrians and shows that the local density has a direct influence on the
stepping characteristics. Furthermore, we study the phenomena of
synchronization -walking in lockstep- and show its dependence on flow
densities. We show that the synchronization of steps is particularly important
at high densities, which has direct impact on the studies of optimizing
pedestrians flow in congested situations. However, small synchronization and
antisynchronization effects are found also at very low densities, for which no
steric constraints exist between successive pedestrians, showing the natural
tendency to synchronize according to perceived visual signals.Comment: 8 pages, 5 figure
NASA Space Flight Vehicle Fault Isolation Challenges
The Space Launch System (SLS) is the new NASA heavy lift launch vehicle and is scheduled for its first mission in 2017. The goal of the first mission, which will be uncrewed, is to demonstrate the integrated system performance of the SLS rocket and spacecraft before a crewed flight in 2021. SLS has many of the same logistics challenges as any other large scale program. Common logistics concerns for SLS include integration of discrete programs geographically separated, multiple prime contractors with distinct and different goals, schedule pressures and funding constraints. However, SLS also faces unique challenges. The new program is a confluence of new hardware and heritage, with heritage hardware constituting seventy-five percent of the program. This unique approach to design makes logistics concerns such as testability of the integrated flight vehicle especially problematic. The cost of fully automated diagnostics can be completely justified for a large fleet, but not so for a single flight vehicle. Fault detection is mandatory to assure the vehicle is capable of a safe launch, but fault isolation is another issue. SLS has considered various methods for fault isolation which can provide a reasonable balance between adequacy, timeliness and cost. This paper will address the analyses and decisions the NASA Logistics engineers are making to mitigate risk while providing a reasonable testability solution for fault isolation
NASA Space Flight Vehicle Fault Isolation Challenges
The Space Launch System (SLS) is the new NASA heavy lift launch vehicle in development and is scheduled for its first mission in 2018.SLS has many of the same logistics challenges as any other large scale program. However, SLS also faces unique challenges related to testability. This presentation will address the SLS challenges for diagnostics and fault isolation, along with the analyses and decisions to mitigate risk.
Challenges in the delivery of e-government through kiosks
Kiosks are increasingly being heralded as a technology through which governments, government departments and local authorities or municipalities can engage with citizens. In particular, they have attractions in their potential to bridge the digital divide. There is some evidence to suggest that the citizen uptake of kiosks and indeed other channels for e-government, such as web sites, is slow, although studies on the use of kiosks for health information provision offer some interesting perspectives on user behaviour with kiosk technology. This article argues that the delivery of e-government through kiosks presents a number of strategic challenges, which will need to be negotiated over the next few years in order that kiosk applications are successful in enhancing accessibility to and engagement with e-government. The article suggests that this involves consideration of: the applications to be delivered through a kiosk; one stop shop service and knowledge architectures; mechanisms for citizen identification; and, the integration of kiosks within the total interface between public bodies and their communities. The article concludes by outlining development and research agendas in each of these areas.</p
- …