45 research outputs found
Wireless strain and temperature monitoring in reinforced concrete using Surface Acoustic Wave (SAW) sensors
Monitoring the health of civil engineering structures using implanted
deformation, temperature and corrosion sensors would further improve
maintenance and extend the service life of those structures. However, sensor
integration poses a number of problems, due to the presence of cables and
on-board electronics. Passive, wireless SAW sensors offer a very promising
solution, here. We used commercial SAW devices mounted on steel rebars to carry
out an initial feasibility study. Without cables or embedded electronics, we
were able to measure the deformation of a concrete beam subjected to bending
load. We were also able to measure the temperature continuously over a
three-week period
Magnetic SAW RFID Sensor Based on Love Wave for Detection of Magnetic Field and Temperature
Magnetic field measurement including a temperature compensation is essential
for a magnetic field sensor. This study investigates a magnetic surface
acoustic wave (MSAW) sensor in a reflective delay line configuration with two
acoustic propagation paths with and without magnetic field sensitive layer. The
delay in path with sensitive layer leads to magnetic field detection and the
one without enable temperature measurement and thus compensation for the first
path. The developed sensor is based on a ZnO/LiNbO Ycut (X-direction)
layered structure as Love wave platform. Love wave as a shear wave being more
favorable for magnetic detection. Co-Fe-B is considered as sensitive layer to
detect magnetic field changes and is deposited on the top of ZnO, but only on
one of the two paths. We combined an original configuration of connected IDTs
with a high electromechanical coupling coefficient (K) mode to improve the
signal amplitude. The achieved sensor exhibits a high temperature and magnetic
field sensitivity of -63 ppm/C and -781 ppm/mT, respectively. The
temperature compensation method for magnetic field measurement is demonstrated
using a differential measurement by subtracting the delay times obtained for
the two paths with and without the sensitive layer. Finally, The sensor
exhibited good repeatability at various temperatures. Moreover, the device
developed allows in addition to the multisensor functionality, the radio
frequency identification (RFID) which is necessary for the deployment of sensor
networks
SAW RFID devices using connected IDTs as an alternative to conventional reflectors for harsh environments
International audienceRemote interrogation of surface acoustic wave ID-tags imposes a high signal amplitude which is related to a high coupling coefficient value (K 2) and low propagation losses (α). In this paper, we propose and discuss an alternative configuration to the standard one. Here, we replaced the conventional configuration, i.e. one interdigital transducer (IDT) and several reflectors, by a series of electrically connected IDTs. The goal is to increase the amplitude of the detected signal using direct transmission between IDTs instead of the reflection from passive reflectors. This concept can therefore increase the interrogation scope of ID-tags made on conventional substrate with high K 2 value. Moreover, it can also be extended to suitable substrates for harsh environments such as high temperature environments: the materials used exhibit limited performances (low K 2 value and relatively high propagation losses) and are therefore rarely used for identification applications. The concept was first tested and validated using the lithium niobate 128°Y-X cut substrate, which is commonly used in ID-tags. A good agreement between experimental and numerical results was obtained for the promising concept of connected IDTs. The interesting features of the structure were also validated using a langasite substrate, which is well-known to operate at very high temperatures. Performances of both substrates (lithium niobate and langasite) were tested with an in-situ RF characterization up to 600°C. Unexpected results regarding the resilience of devices based on congruent lithium niobate were obtained. Index Terms-high temperature, lithium niobate, radio frequency identification (RFID), surface acoustic wave (SAW
Intrinsic versus shape anisotropy in micro-structured magnetostrictive thin films for magnetic surface acoustic wave sensors
International audienceThis work aims at studying the interaction between surface acoustic waves (SAW) and micro-structured magnetostrictive layers under a magnetic field with a perspective to develop magnetic field sensors. The impact of the competition between the strong intrinsic magnetic anisotropy of the magnetic material and the shape anisotropy of the interdigitated transducer (IDT) fingers introduced by the micro-structuration is investigated. Therefore, the macroscopic and microscopic magnetic properties of the IDT and their influence on the magneto-acoustic response are studied. A SAW resonator with the IDTs made of the magnetostrictive thin film was elaborated and the magnetic surface acoustic wave (MSAW) response under a magnetic field was performed and discussed. Depending on the energy balance, the anisotropy gets modified and a correlation with the MSAW sensitivity to an externally applied magnetic field is made
Ultrasoft reconfigurable millimeter-wave antennas and devices based on Magneto-Electro-Mechanical Microsystems (MMEMS) : design, fabrication, measurements
Il y a à l'heure actuelle un grand besoin d'antennes reconfigurables dans la bande des 60 GHz pour des applications de télédétection et de télécommunications sans fil très hauts débits. Les solutions traditionnelles de reconfiguration sont basées sur des semiconducteurs ou des composants RF-MEMS, qui connaissent un coût, une complexité et des pertes croissantes en bande millimétrique. Dans cette thèse, une approche originale a été développée : elle est basée sur la reconfiguration mécanique d'antennes et dispositifs millimétriques microrubans sur substrat élastomère ultrasouple PDMS grâce à des actionneurs MEMS grands déplacements. Premièrement, les choix de conception, la technique de simulation éléments finis (HFSS), et surtout la microfabrication d'antennes sur membrane PDMS ainsi que les techniques de mesure en impédance et rayonnement sont abordés.Deux axes ont ensuite été étudiés : les antennes accordables en fréquence, et les antennes et composants pour le balayage angulaire (déphaseurs et antennes à balayage mécanique de type scanner). Des procédés technologiques innovants ont été développés (reports de métallisations épaisses biocompatibles et d'aimants permanents en couches minces sur membrane PDMS) et différentes techniques d'actionnement (pneumatique, magnétique, par électromouillage) ont été mises en œuvre. Les performances en terme d'accord en fréquence (8,2 %) et de balayage angulaire (-90/+100°) dépassent l'état de l'art des antennes du même type en bande millimétrique, et ceci en utilisant une technologie peu complexe, ultra bas-coût et prometteuse pour la montée en fréquence.There is currently an increasing need for reconfigurable antennas in the 60 GHz band for remote sensing applications and wireless communications. Traditional reconfiguration solutions are based on semiconductors or RF-MEMS but these components face cost, complexity and losses issues at millimeter-waves.In this thesis, an original approach was developed: it is based on the mechanical reconfiguration of millimeter-wave microstrip antennas and devices printed on ultrasoft PDMS substrates, thank to large displacements MEMS actuators. First, the design choices, the finite element simulation technique (HFSS), and the microfabrication of antennas supported by PDMS membranes as well as the impedance and radiation measurements techniques have been discussed. Two axis have then been studied: frequency-tunable antennas, and beam-steering components (phase shifters and "scanner" type antennas). Innovative technological processes were developed (transfer of biocompatible metal patterns and permanent magnet thin films on PDMS membranes) and several actuation techniques (pneumatic, magnetic, electrowetting) were implemented. Performances in terms of frequency tuning (8.2%) and scan angles (-90 / 100 °) are beyond the state of the art for similar antennas in the millimeter-wave band, and are achieved by using a very simple, ultra low-cost technique that is expected to be effective at even higher frequencies
Antennes et dispositifs hyperfréquences millimétriques ultrasouples reconfigurables à base de Microsystèmes Magnéto-Electro-Mécaniques (MMEMS) : conception, réalisation, mesures
There is currently an increasing need for reconfigurable antennas in the 60 GHz band for remote sensing applications and wireless communications. Traditional reconfiguration solutions are based on semiconductors or RF-MEMS but these components face cost, complexity and losses issues at millimeter-waves.In this thesis, an original approach was developed: it is based on the mechanical reconfiguration of millimeter-wave microstrip antennas and devices printed on ultrasoft PDMS substrates, thank to large displacements MEMS actuators. First, the design choices, the finite element simulation technique (HFSS), and the microfabrication of antennas supported by PDMS membranes as well as the impedance and radiation measurements techniques have been discussed. Two axis have then been studied: frequency-tunable antennas, and beam-steering components (phase shifters and "scanner" type antennas). Innovative technological processes were developed (transfer of biocompatible metal patterns and permanent magnet thin films on PDMS membranes) and several actuation techniques (pneumatic, magnetic, electrowetting) were implemented. Performances in terms of frequency tuning (8.2%) and scan angles (-90 / 100 °) are beyond the state of the art for similar antennas in the millimeter-wave band, and are achieved by using a very simple, ultra low-cost technique that is expected to be effective at even higher frequencies.Il y a à l'heure actuelle un grand besoin d'antennes reconfigurables dans la bande des 60 GHz pour des applications de télédétection et de télécommunications sans fil très hauts débits. Les solutions traditionnelles de reconfiguration sont basées sur des semiconducteurs ou des composants RF-MEMS, qui connaissent un coût, une complexité et des pertes croissantes en bande millimétrique. Dans cette thèse, une approche originale a été développée : elle est basée sur la reconfiguration mécanique d'antennes et dispositifs millimétriques microrubans sur substrat élastomère ultrasouple PDMS grâce à des actionneurs MEMS grands déplacements. Premièrement, les choix de conception, la technique de simulation éléments finis (HFSS), et surtout la microfabrication d'antennes sur membrane PDMS ainsi que les techniques de mesure en impédance et rayonnement sont abordés.Deux axes ont ensuite été étudiés : les antennes accordables en fréquence, et les antennes et composants pour le balayage angulaire (déphaseurs et antennes à balayage mécanique de type scanner). Des procédés technologiques innovants ont été développés (reports de métallisations épaisses biocompatibles et d'aimants permanents en couches minces sur membrane PDMS) et différentes techniques d'actionnement (pneumatique, magnétique, par électromouillage) ont été mises en œuvre. Les performances en terme d'accord en fréquence (8,2 %) et de balayage angulaire (-90/+100°) dépassent l'état de l'art des antennes du même type en bande millimétrique, et ceci en utilisant une technologie peu complexe, ultra bas-coût et prometteuse pour la montée en fréquence
Dynamic light scattering study of the ultrasonication of P(VDF-TrFE): A new model
International audienceThe purpose of this paper is to understand the mechanisms occurring during the ultrasonication of the copolymer P(VDF-TrFE). In these experimental conditions, the polymer adopts a core-shell structure and its hydrodynamic diameter is measured by dynamic light scattering (DLS). The results show that, without covalent bonds breakage, the hydrodynamic diameter decreases with ultrasonication time and a smaller size population appears. This evolution is reversible in a matter of days. A new two-step mechanism is proposed to describe this phenomenon: firstly the erosion of a core-shell structure and secondly the contraction of the core. Beyond shedding a new light on the phenomena occurring during the sonication of polymers used in nanocomposites elaboration, this work also strongly questions the traditional techniques used to study the degradation of polymers, which uses the hydrodynamic diameter measurement to determine the molecular weight
Investigation of the limit operating temperature of LiNbO3 as substrate for SAW devices
International audienc