296 research outputs found

    Hypervelocity particle capture: Some considerations regarding suitable target media

    Get PDF
    Hypervelocity particles colliding with passive capture media will be traversed by shock waves; depending on the stress amplitude, the particle may remain solid or it may melt or vaporize. Any capture mechanism considered for cosmic dust collection in low Earth-orbit must be designed such that sample alteration and hence loss of scientific information is minimized. Capture of pristine particles is fundamentally difficult, because the specific heat of melting and even vaporization is exceeded upon impact at typical, geocentric encounter velocities. From the results of calculated and observed melting behaviors it is concluded that shock stresses in excess of 50 GPA should be avoided during hypervelocity particle capture on board Space Station and that stresses 20 GPa, even at 15 km/s collision velocities, should constitute desirable instrument design goals. Some principal characteristics of the capture medium that may satisfy these requirements are identified

    The Discussion Goes on: What Is the Role of Euryarchaeota in Humans?

    Get PDF
    The human body (primarily the intestinal tract, the oral cavity, and the skin) harbours approximately 1,000 different bacterial species. However, the number of archaeal species known to colonize man seems to be confined to a handful of organisms within the class Euryarchaeota (including Methanobrevibacter smithii, M. oralis, and Methanosphaera stadtmanae). In contrast to this conspicuously low diversity of Archaea in humans their unique physiology in conjunction with the growing number of reports regarding their occurrence at sites of infection has made this issue an emerging field of study. While previous review articles in recent years have addressed the putative role of particularly methanogenic archaea for human health and disease, this paper compiles novel experimental data that have been reported since then. The aim of this paper is to inspire the scientific community of “Archaea experts” for those unique archaeal organisms that have successfully participated in the human-microbe coevolution

    Nanoscale Mineralogy and Composition of Experimental Regolith Agglutinates Produced under Asteroidal Impact Conditions

    Get PDF
    On the Moon, the energetics of smaller impactors and the physical/chemical characteristics of the granular regolith target combine to form a key product of lunar space weathering: chemically reduced shock melts containing optically-active nanophase Fe metal grains (npFe0) [1]. In addition to forming the optically dark glassy matrix phase in lunar agglutinitic soil particles [1], these shock melts are becoming increasingly recognized for their contribution to optically active patina coatings on a wide range of exposed rock and grain surfaces in the lunar regolith [2]. In applying the lessons of lunar space weathering to asteroids, the potential similarities and differences in regolith-hosted shock melts on the Moon compared to those on asteroids has become a topic of increasing interest [3,4]. In a series of impact experiments performed at velocities applicable to the asteroid belt [5], Horz et al. [6] and See and Horz [7] have previously shown that repeated impacts into a gabbroic regolith analog target can produce melt-welded grain aggregates morphologically very similar to lunar agglutinates [6,7]. Although these agglutinate-like particles were extensively analyzed by electron microprobe and scanning electron microscopy (SEM) as part of the original study [7], a microstructural and compositional comparison of these aggregates to lunar soil agglutinates at sub-micron scales has yet to be made. To close this gap, we characterized a representative set of these aggregates using a JEOL 7600 field-emission scanning electron microscope (FE-SEM), and JEOL 2500SE field-emission scanning transmission electron microscope (FE-STEM) both optimized for energy dispersive X-ray spectroscopy (EDX) compositional spectrum imaging at respective analytical spatial resolutions of 0.5 to 1 micron, and 2 to 4 nm

    Cratering and penetration experiments in teflon targets at velocities from 1 to 7 km/s

    Get PDF
    Approximately 20 sq m of protective thermal blankets, largely composed of Teflon, were retrieved from the Long Duration Exposure Facility after the spacecraft spent approximately 5.7 years in space. Examination of these blankets revealed that they contained thousands of hypervelocity impact features ranging from micron-sized craters to penetration holes several millimeters in diameter. We conducted impact experiments to reproduce such features and to understand the relationships between projectile size and the resulting crater or penetration hole diameter over a wide range of impact velocities. Such relationships are needed to derive the size and mass frequency distribution and flux of natural and man-made particles in low-earth orbit. Powder propellant and light-gas guns were used to launch soda-lime glass spheres into pure Teflon targets at velocities ranging from 1 to 7 km/s. Target thickness varied over more than three orders of magnitude from finite halfspace targets to very thin films. Cratering and penetration of massive Teflon targets is dominated by brittle failure and the development of extensive spall zones at the target's front and, if penetrated, the target's rear side. Mass removal by spallation at the back side of Teflon targets may be so severe that the absolute penetration hole diameter can become larger than that of a standard crater. The crater diameter in infinite halfspace Teflon targets increases, at otherwise constant impact conditions, with encounter velocity by a factor of V (exp 0.44). In contrast, the penetration hole size in very thin foils is essentially unaffected by impact velocity. Penetrations at target thicknesses intermediate to these extremes will scale with variable exponents of V. Our experimental matrix is sufficiently systematic and complete, up to 7 km/s, to make reasonable recommendations for velocity-scaling of Teflon craters and penetrations. We specifically suggest that cratering behavior and associated equations apply to all impacts in which the shock-pulse duration of the projectile is shorter than that assigned a unique projectile size, provided an impact velocity is known or assumed. This calibration seems superior to the traditional ballistic-limit approach

    Penetration experiments in aluminum 1100 targets using soda-lime glass projectiles

    Get PDF
    The cratering and penetration behavior of annealed aluminum 1100 targets, with thickness varied from several centimeters to ultra-thin foils less than 1 micrometer thick, were experimentally investigated using 3.2 mm diameter spherical soda-lime glass projectiles at velocities from 1 to 7 km/s. The objective was to establish quantitative, dimensional relationships between initial impact conditions (impact velocity, projectile diameter, and target thickness) and the diameter of the resulting crater or penetration hole. Such dimensional relationships and calibration experiments are needed to extract the diameters and fluxes of hypervelocity particles from space-exposed surfaces and to predict the performance of certain collisional shields. The cratering behavior of aluminum 1100 is fairly well predicted. However, crater depth is modestly deeper for our silicate impactors than the canonical value based on aluminum projectiles and aluminum 6061-T6 targets. The ballistic-limit thickness was also different. These differences attest to the great sensitivity of detailed crater geometry and penetration behavior on the physical properties of both the target and impactor. Each penetration experiment was equipped with a witness plate to monitor the nature of the debris plume emanating from the rear of the target. This plume consists of both projectile fragments and target debris. Both penetration hole and witness-plate spray patterns systematically evolve in response to projectile diameter/target thickness. The relative dimensions of the projectile and target totally dominate the experimental products documented in this report; impact velocity is an important contributor as well to the evolution of penetration holes, but is of subordinate significance for the witness-plate spray patterns

    Aerogel Track Morphology: Measurement, Three Dimensional Reconstruction and Particle Location using Confocal Laser Scanning Microscopy

    Get PDF
    The Stardust spacecraft returned the first undoubted samples of cometary dust, with many grains embedded in the silica aerogel collector . Although many tracks contain one or more large terminal particles of a wide range of mineral compositions , there is also abundant material along the track walls. To help interpret the full particle size, structure and mass, both experimental simulation of impact by shots and numerical modeling of the impact process have been attempted. However, all approaches require accurate and precise measurement of impact track size parameters such as length, width and volume of specific portions. To make such measurements is not easy, especially if extensive aerogel fracturing and discoloration has occurred. In this paper we describe the application and limitations of laser confocal imagery for determination of aerogel track parameters, and for the location of particle remains

    ZyFISH: A Simple, Rapid and Reliable Zygosity Assay for Transgenic Mice

    Get PDF
    Microinjection of DNA constructs into fertilized mouse oocytes typically results in random transgene integration at a single genomic locus. The resulting transgenic founders can be used to establish hemizygous transgenic mouse lines. However, practical and experimental reasons often require that such lines be bred to homozygosity. Transgene zygosity can be determined by progeny testing assays which are expensive and time-consuming, by quantitative Southern blotting which is labor-intensive, or by quantitative PCR (qPCR) which requires transgene-specific design. Here, we describe a zygosity assessment procedure based on fluorescent in situ hybridization (zyFISH). The zyFISH protocol entails the detection of transgenic loci by FISH and the concomitant assignment of homozygosity using a concise and unbiased scoring system. The method requires small volumes of blood, is scalable to at least 40 determinations per assay, and produces results entirely consistent with the progeny testing assay. This combination of reliability, simplicity and cost-effectiveness makes zyFISH a method of choice for transgenic mouse zygosity determinations

    Specific detection of Salmonella enterica and Escherichia coli strains by using ELISA with bacteriophages as recognition agents

    Get PDF
    The use of bacteriophages, instead of antibodies, in the ELISA-based detection of bacterial strains was tested. This procedure appeared to be efficient, and specific strains of Salmonella enterica and Escherichia coli could be detected. The sensitivity of the assay was about 105 bacterial cells/well (106/ml), which is comparable with or outperforms other ELISA tests detecting intact bacterial cells without an enrichment step. The specificity of the assay depends on the kind of bacteriophage used. We conclude that the use of bacteriophages in the detection and identification of bacteria by an ELISA-based method can be an alternative to the use of specific antibodies. The advantages of the use of bacteriophages are their environmental abundance (and, thus, a possibility to isolate various phages with different specificities) and the availability of methods for obtaining large amounts of phage lysates, which are simple, rapid, cheap, and easy

    STARDUST Curation and Science at JSC

    Get PDF
    Dust particles released from comet 81P/Wild-2 were captured in silica aerogel on-board the STARDUST spacecraft and returned to Earth on January 15, 2006. STARDUST recovered thousands of particles ranging in size from 1 to 100 micrometers. During the six month Preliminary Examination period an international consortium of 180 scientists investigated their mineralogy/petrology, organic/inorganic chemistry, optical properties and isotopic compositions. Stardust samples are now available for research by the entire research community

    Probiotic Lactobacillus paracasei effect on cariogenic bacterial flora

    Get PDF
    Lactobacillus paracasei has been demonstrated to inhibit the growth of many pathogenic microbes such as Streptococcus mutans, in vitro. However, its clinical application remains unclear. Here, we examined whether a novel probiotic L. paracasei GMNL-33 may reduce the caries-associated salivary microbial counts in healthy adults. Seventy-eight subjects (aged 20 to 26) had completed this double-blinded, randomized, placebo-controlled study. A probiotic/test (n = 42) and a control group (n = 36) took a L. paracasei GMNL-33 and a placebo oral tablet three times per day for 2 weeks, respectively. Bacterial counts of salivary S. mutans, lactobacilli, and salivary buffer capacity were measured with chair-side kits at the beginning (T1), the completion (T2) of medication, and 2 weeks after medication (T3). The results did not show differences in the counts of S. mutans and lactobacilli between probiotic and control groups at T1, T2, and T3. Nevertheless, within the probiotic group, an interesting probiotic effect was noticed. Between T1 and T2, no inhibitory effect against S. mutans was observed. However, a significant count reduction in the salivary S. mutans was detected between T2 and T3 (p = 0.016). Thus, a 2-week period of medication via oral administration route may be needed for L. paracasei GMNL-33 to be effective in the probiotic action
    corecore