Creation and control of a two-dimensional electron liquid at the bare SrTiO3 surface

Many-body interactions in transition-metal oxides give rise to a wide range of functional properties, such as high-temperature superconductivity, colossal magnetoresistance, or multiferroicity. The seminal recent discovery of a two-dimensional electron gas (2DEG) at the interface of the insulating oxides LaAlO3 and SrTiO3 represents an important milestone towards exploiting such properties in all-oxide devices. This conducting interface shows a number of appealing properties, including a high electron mobility, superconductivity, and large magnetoresistance and can be patterned on the few-nanometer length scale. However, the microscopic origin of the interface 2DEG is poorly understood. Here, we show that a similar 2DEG, with an electron density as large as 8x10^13 cm^-2, can be formed at the bare SrTiO3 surface. Furthermore, we find that the 2DEG density can be controlled through exposure of the surface to intense ultraviolet (UV) light. Subsequent angle-resolved photoemission spectroscopy (ARPES) measurements reveal an unusual coexistence of a light quasiparticle mass and signatures of strong many-body interactions.Comment: 14 pages, 4 figures, supplementary information (see other files

Pass wear resistance for perpendicular recording media

金沢大学理工研究域数物科学系Pass wear resistance of sputtered CoCr perpendicular flexible disks has been investigated. The disk was composed of CoCr film on a heat-resistant base film, a protection layer, and lubricant. The pass wear durabilities were evaluated for a conventional double-sided 3.5-in drive. It was found that the scratch depth (SD) per load force (LF) depends on preparation conditions, and that the CoCr film hardness is related to pass wear durability. SD/LF values range from 0.2 to 0.3 for CoCr films without a protective layer. With a protective layer and lubricant, the range of SD/LF values varies from 0.2-0.3 to 0.1-0.3. The disk hardness, especially for small SD/LF media, has been improved. A pass wear durability of 30 million passes was attained for a disk having SD/LF = 0.1

Kinetic frustration and the nature of the magnetic and paramagnetic states in iron pnictides and iron chalcogenides

The iron pnictide and chalcogenide compounds are a subject of intensive investigations due to their high temperature superconductivity.\cite{a-LaFeAsO} They all share the same structure, but there is significant variation in their physical properties, such as magnetic ordered moments, effective masses, superconducting gaps and T$_c$. Many theoretical techniques have been applied to individual compounds but no consistent description of the trends is available \cite{np-review}. We carry out a comparative theoretical study of a large number of iron-based compounds in both their magnetic and paramagnetic states. We show that the nature of both states is well described by our method and the trends in all the calculated physical properties such as the ordered moments, effective masses and Fermi surfaces are in good agreement with experiments across the compounds. The variation of these properties can be traced to variations in the key structural parameters, rather than changes in the screening of the Coulomb interactions. Our results provide a natural explanation of the strongly Fermi surface dependent superconducting gaps observed in experiments\cite{Ding}. We propose a specific optimization of the crystal structure to look for higher T$_c$ superconductors.Comment: 5 pages, 3 figures with a 5-page supplementary materia

Primary Bone Formation in Porous Hydroxyapatite Ceramic: A Light and Scanning Electron Microscopic Study

Porous hydroxyapatite ceramics combined with rat marrow cells were implanted subcutaneously in the back of syngeneic Fischer rats . Fluorochrome-labeling (calcein, tetracycline) was performed post-operatively and the ceramics were harvested 4 weeks after implantation. Undecalcified thin sections of the implants were observed under light microscopy or fluoromicroscopy and the corresponding areas were also analyzed in a scanning electron microscope connected to an electron probe microanalyzer (SEM-EPMA). Many pore areas of the ceramics showed bone and osteoid formation together with active osteoblasts. The bone formation began directly on the surface of the ceramic and proceeded in a centripetal direction towards the center of the pores. SEM-EPMA analysis revealed continuous high levels of calcium and phosphorus in bone/ceramic interface and a gradual decrease of these levels in the osteoid region. These results indicate that the interaction between osteoblasts and ceramic surface resulted in bone formation

Uniaxial Tensile Stress-Strain Relationships of RC Elements Strengthened with FRP Sheets

The shear behavior of fiber-reinforced-polymer–strengthened reinforced concrete (FRP-strengthened RC) members is not fully developed and accurately predicted because of the lack of accurate constitutive laws for the components of the composite members. This paper presents experimental and analytical investigations of tensile stress-strain relationships of concrete and steel in FRP-strengthened RC members. These stress-strain relationships are required in formulations of softened truss models to predict the shear behavior of the FRP-strengthened RC element. Thirteen full-scale FRP-strengthened RC prismatic specimens with different FRP reinforcement ratios, steel reinforcement ratios, and FRP wrapping schemes were tested under uniaxial tension loading. The results show that the tensile behavior of the concrete and steel is altered because of the externally bonded FRP sheets. Modified constitutive laws are proposed and incorporated in the softened membrane model (SMM) to demonstrate through two tests the behavior of FRP-strengthened RC element subjected to pure shear. Moreover, crack spacing and crack width were studied and compared with existing code provisions