32,216 research outputs found

    The gradational history of southern Ismenius Lacus

    Get PDF
    Two epochs of accelerated gradation affected the geomorphic evolution of southern Ismenius Lacus. These periods of enhanced gradational activity were likely related to periods of more clement climate induced by release of either recycled exogenic or juvenile endogenic atmospheric volatiles. Variations in the intensity and duration of gradation during the second epoch are indicated by the variability in the timing of cessation and degree of air fall deposit removal across the study area. Overall intensity of gradation decreased through successive epochs based on: (1) the decreasing diameter at which cumulative statistics from the respective surfaces cease to follow the expected production function; and (2) the decrease in size/increase in density of preserved valley networks incised into surfaces of differing age. A comparable decrease in valley density with time has been noted in the Isidis region

    Thin film temperature sensor

    Get PDF
    Thin film surface temperature sensors were developed. The sensors were made of platinum-platinum/10 percent rhodium thermocouples with associated thin film-to-lead wire connections and sputtered on aluminum oxide coated simulated turbine blades for testing. Tests included exposure to vibration, low velocity hydrocarbon hot gas flow to 1250 K, and furnace calibrations. Thermal electromotive force was typically two percent below standard type S thermocouples. Mean time to failure was 42 hours at a hot gas flow temperature of 1250 K and an average of 15 cycles to room temperature. Failures were mainly due to separation of the platinum thin film from the aluminum oxide surface. Several techniques to improve the adhesion of the platinum are discussed

    Characteristics of ejecta and alluvial deposits at Meteor Crater, Arizona and Odessa Craters, Texas: Results from ground penetrating radar

    Get PDF
    Previous ground penetrating radar (GRP) studies around 50,000 year old Meteor Crater revealed the potential for rapid, inexpensive, and non-destructive sub-surface investigations for deep reflectors (generally greater than 10 m). New GRP results are summarized focusing the shallow sub-surfaces (1-2 m) around Meteor Crater and the main crater at Odessa. The following subject areas are covered: (1) the thickness, distribution, and nature of the contact between surrounding alluvial deposits and distal ejecta; and (2) stratigraphic relationships between both the ejecta and alluvium derived from both pre and post crater drainages. These results support previous conclusions indicating limited vertical lowering (less than 1 m) of the distal ejecta at Meteor Crater and allow initial assessment of the gradational state if the Odessa craters

    Collective Spin-Density-Wave Response Perpendicular to the Chains of the Quasi One-Dimensional Conductor (TMTSF)2PF6

    Full text link
    Microwave experiments along all three directions of the spin-density-wave model compound (TMTSF)2_2PF6_6 reveal that the pinned mode resonance is present along the aa and b′b^{\prime} axes. The collective transport is considered to be the fingerprint of the condensate. In contrast to common quasi one-dimensional models, the density wave also slides in the perpendicular b′b^{\prime} direction. The collective response is absent along the least conducting c∗c^* direction.Comment: 3 pages, 4 figure

    Turbine Blade Temperature Measurements Using Thin Film Temperature Sensors

    Get PDF
    The development of thin film temperature sensors is discussed. The technology for sputtering 2 micron thin film platinum versus platinum 10 percent rhodium thermocouples on alumina forming coatings was improved and extended to applications on actual turbine blades. Good adherence was found to depend upon achieving a proper morphology of the alumina surface. Problems of adapting fabrication procedures to turbine blades were uncovered, and improvements were recommended. Testing at 1250 K at one atmosphere pressure was then extended to a higher Mach No. (0.5) in combustor flow for 60 hours and 71 thermal cycles. The mean time to failure was 47 hours accumulated during 1 hour exposures in the combustor. Calibration drift was about 0.1 percent per hour, attributable to oxidation of the rhodium in the thin films. An increase in film thickness and application of a protective overcoat are recommended to reduce drift in actual engine testing
    • …
    corecore