Material modelling and springback analysis for multi-stage rotary draw bending of thin-walled tube using homogeneous anisotropic hardening model

The aim of this paper is to compare several hardening models and to show their relevance for the prediction of springback and deformation of an asymmetric aluminium alloy tube in multi-stage rotary draw bending process. A three-dimensional finite-element model of the process is developed using the ABAQUS code. For material modelling, the newly developed homogeneous anisotropic hardening model is adopted to capture the Bauschinger effect and transient hardening behaviour of the aluminium alloy tube subjected to non-proportional loading. The material parameters of the hardening model are obtained from uniaxial tension and forward-reverse shear test results of tube specimens. This work shows that this approach reproduces the transient Bauschinger behaviour of the material reasonably well. However, a curve-crossing phenomenon observed for this material cannot be captured by the homogeneous anisotropic hardening model. For comparison purpose, the isotropic and combined isotropic-kinematic hardening models are also adopted for the analysis of the same problem. The predictions of springback and cross-section deformation based on these models are discussed. (C) 2014 The Authors. Published by Elsevier Ltd.open1134Nsciescopu

Numerical simulation of the mechanical response during strain path change: application to Zn alloys.

The microstructure-based hardening model (Beyerlein and Tome, 2007), that accounts for the dislocation reversal-related mechanisms and the cut-through effect, is extended to HCP metals. This model, which is embedded in the visco-plastic self-consistent framework, is applied in this work to predict the mechanical response of Zn alloy during strain path change. The predicted mechanical behavior and texture evolution during pre-loading and reloading is in good agreement with experimental observations. The change in hardening behavior after reloading is well reproduced by this model. The contributions of the different mechanisms are also analyzed. (C) 2014 Published by Elsevier Ltd.open1111Nsciescopu

Computer-aided simulation of a rotary sputtering magnetron

In the past, computer-aided simulation of sputtering magnetron has been applied mainly to planar cathodes with flat target surfaces. In this work, we have simulated the target erosion profile of a cylindrical rotary magnetron by tracing electron trajectories and predicting ionization distribution. The electric potential is prescribed as a radial function. A fourth-order Runge–Kutta method is used to solve the electron movement equations, and a Monte Carlo method is employed to predict electron/Ar collision. It is shown that the simulation can predict the target erosion with reasonable accuracy. © 2004 American Institute of Physics.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/71287/2/JAPIAU-95-11-6017-1.pd

Hardening behavior and texture evolution of TWIP steel during strain path change

Polycrystal materials exhibit large changes in the flow stress and hardening behavior during the strain path change. Such changes are related with the crystallographic texture anisotropy and the rearrangement of dislocation structure during the pre-loading. These effects have been captured by a dislocation hardening model embedded in the visco-plastic self-consistent (VPSC) model. In this work, the texture evolution and mechanical behavior of TWIP steel during the strain path change are investigated. The experimental studies are carried out on rolled TWIP steel sheet. The mechanical responses are obtained under tensile tests along rolling direction, followed by tension along the directions with 0 degrees and 90 degrees from the pre-loading direction. The simulated results of strain-stress curves and the texture evolution are in good agreement with the experimental data.110Ysciescopu

Comparison of Flight Simulators Based on Human Motion Perception Metrics

In flight simulation, motion filters are used to transform aircraft motion into simulator motion. When looking for the best match between visual and inertial amplitude in a simulator, researchers have found that there is a range of inertial amplitudes, rather than a single inertial value, that is perceived by subjects as optimal. This zone, hereafter referred to as the optimal zone, seems to correlate to the perceptual coherence zones measured in flight simulators. However, no studies were found in which these two zones were compared. This study investigates the relation between the optimal and the coherence zone measurements within and between different simulators. Results show that for the sway axis, the optimal zone lies within the lower part of the coherence zone. In addition, it was found that, whereas the width of the coherence zone depends on the visual amplitude and frequency, the width of the optimal zone remains constant

Deposition Mechanism and Properties of Thin Polydopamine Films for High Added Value Applications in Surface Science at the Nanoscale

Polydopamine films have been introduced by Messersmith et al. as a possible “versatile” surface functionalization method allowing to coat the surface of almost all known materials even superhydrophobic surfaces. These new kinds of coatings also confer a plethora of functionalities to the coated materials owing to the complex chemistry of the catechol quinone moieties present on the surface of polydopamine. These coatings may hence become an interesting alternative to established surface coatings like self-assembled monolayers and polyelectrolyte multilayered films. In this review, we describe the knowledge acquired in the last 3 years about the deposition mechanisms of polydopamine films, their properties, and various applications in surface science at the nanoscale.Fonds Europeen de Developpement Economique et Regional (Chaptochem Project 2009-02-039-35

Local piezoresponse and polarization switching in nucleobase thymine microcrystals

Thymine (2-oxy-4-oxy-5 methyl pyrimidine) is one of the four nucleobases of deoxyribonucleic acid (DNA). In the DNA molecule, thymine binds to adenine via two hydrogen bonds, thus stabilizing the nucleic acid structure and is involved in pairing and replication. Here, we show that synthetic thymine microcrystals grown from the solution exhibit local piezoelectricity and apparent ferroelectricity, as evidenced by nanoscale electromechanical measurements via Piezoresponse Force Microscopy. Our experimental results demonstrate significant electromechanical activity and polarization switchability of thymine, thus opening a pathway for piezoelectric and ferroelectric-based applications of thymine and, perhaps, of other DNA nucleobase materials. The results are supported by molecular modeling of polarization switching under an external electric field. (C) 2015 AIP Publishing LLC