Generalised action-angle coordinates defined on island chains

Straight-field-line coordinates are very useful for representing magnetic fields in toroidally confined plasmas, but fundamental problems arise regarding their definition in 3-D geometries because of the formation of islands and chaotic field regions, ie non-integrability. In Hamiltonian dynamical systems terms these coordinates are a form of action-angle variables, which are normally defined only for integrable systems. In order to describe 3-D magnetic field systems, a generalisation of this concept was proposed recently by the present authors that unified the concepts of ghost surfaces and quadratic-flux-minimising (QFMin) surfaces. This was based on a simple canonical transformation generated by a change of variable $\theta = \theta(\Theta,\zeta)$, where $\theta$ and $\zeta$ are poloidal and toroidal angles, respectively, with $\Theta$ a new poloidal angle chosen to give pseudo-orbits that are a) straight when plotted in the $\zeta,\Theta$ plane and b) QFMin pseudo-orbits in the transformed coordinate. These two requirements ensure that the pseudo-orbits are also c) ghost pseudo-orbits. In the present paper, it is demonstrated that these requirements do not \emph{uniquely} specify the transformation owing to a relabelling symmetry. A variational method of solution that removes this lack of uniqueness is proposed.Comment: 10 pages. Accepted by Plasma Physics and Controlled Fusion as part of a cluster of refereed papers in a special issue containing papers arising from the Joint International Stellarator & Heliotron Workshop and Asia-Pacific Plasma Theory Conference, held in Canberra and Murramarang Resort, Australia, 30 January - 3 February, 201

Vortex-type elastic structured media and dynamic shielding

The paper addresses a novel model of metamaterial structure. A system of spinners has been embedded into a two-dimensional periodic lattice system. The equations of motion of spinners are used to derive the expression for the chiral term in the equations describing the dynamics of the lattice. Dispersion of elastic waves is shown to possess innovative filtering and polarization properties induced by the vortextype nature of the structured media. The related homogenised effective behavior is obtained analytically and it has been implemented to build a shielding cloak around an obstacle. Analytical work is accompanied by numerical illustrations.Comment: 24 pages, 13 figure

Oxygen Cost of Recreational Horse-Riding in Females

Version: as accepted for publication.BACKGROUND: The purpose of this study was to characterize the physiological demands of a riding session comprising different types of recreational horse riding in females. METHODS: Sixteen female recreational riders (aged 17 to 54 years) completed an incremental cycle ergometer exercise test to determine peak oxygen consumption (VO₂peak) and a 45-minute riding session based upon a British Horse Society Stage 2 riding lesson (including walking, trotting, cantering and work without stirrups). Oxygen consumption (VO₂), from which metabolic equivalent (MET) and energy expenditure values were derived, was measured throughout. RESULTS: The mean VO₂ requirement for trotting/cantering (18.4 ± 5.1 ml·kg⁻¹·min⁻¹; 52 ± 12% VO₂peak; 5.3 ± 1.1 METs) was similar to walking/trotting (17.4 ± 5.1 ml·kg⁻¹·min⁻¹; 48 ± 13% VO₂peak; 5.0 ± 1.5 METs) and significantly higher than for work without stirrups (14.2 ± 2.9 ml·kg⁻¹·min⁻¹; 41 ± 12% VO₂peak; 4.2 ± 0.8 METs) (P = .001). CONCLUSIONS: The oxygen cost of different activities typically performed in a recreational horse riding session meets the criteria for moderate intensity exercise (3-6 METs) in females, and trotting combined with cantering imposes the highest metabolic demand. Regular riding could contribute to the achievement of the public health recommendations for physical activity in this population

Advanced Gas Turbine (AGT): Power-train system development

Technical work on the design and effort leading to the testing of a 74.5 kW (100 hp) automotive gas turbine is described. The general effort was concentrated on building an engine for test starting in July. The buildup progressed with only routine problems and the engine was delivered to the test stand 9 July. In addition to the engine build effort, work continued in selected component areas. Ceramic turbine parts were built and tested. Burst tests of ceramic rotors show strengths are approaching that achieved in test bars; proof testing is required for acceptable strength ceramic vanes. Over 25 hours was accumulated on the combustor rig in three test modes: pilot nozzle only, start nozzle, and main nozzle operation. Satisfactory ignition was achieved for a wide range of starting speeds and the lean blowout limit was as low as 0.06 kg/b (0.14 lb/hr). Lean blowout was more a function of nozzle atomization than fuel/air ratio. A variety of cycle points were tested. Transition from start nozzle flow to main nozzle flow was done manually without difficulty. Regenerator parts were qualification tested without incident and the parts were assembled on schedule. Rig based performance matched first build requirements. Repeated failures in the harmonic drive gearbox during rig testing resulted in that concept being abandoned for an alternate scheme

Techniques development for whale migration tracking

Effort leading to the completion of development and fabrication of expansible whale harnesses and whale-carried instrument pods is described, along with details of the gear. Early preparative effort for a January-February 1974 field expedition is reported

On Dwarf Galaxies as the Source of Intracluster Gas

Recent observational evidence for steep dwarf galaxy luminosity functions in several rich clusters has led to speculation that their precursors may be the source of the majority of gas and metals inferred from intracluster medium (ICM) x-ray observations. Their deposition into the ICM is presumed to occur through early supernovae-driven winds, the resultant systems reflecting the photometric and chemical properties of the low luminosity dwarf spheroidals and ellipticals we observe locally. We consider this scenario, utilising a self-consistent model for spheroidal photo-chemical evolution and gas ejection via galactic superwinds. Insisting that post-wind dwarfs obey the observed colour-luminosity-metallicity relations, we conclude that the bulk of the ICM gas and metals does not originate within their precursors.Comment: 43 pages, 8 figures, LaTeX, also available at http://msowww.anu.edu.au/~gibson/publications.html, to appear in ApJ, Vol 473, 1997, in pres

Preoperative neutrophil-lymphocyte ratio and outcome from coronary artery bypass grafting

Background: An elevated preoperative white blood cell count has been associated with a worse outcome after coronary artery bypass grafting (CABG). Leukocyte subtypes, and particularly the neutrophil-lymphocyte (N/L) ratio, may however, convey superior prognostic information. We hypothesized that the N/L ratio would predict the outcome of patients undergoing surgical revascularization. Methods: Baseline clinical details were obtained prospectively in 1938 patients undergoing CABG. The differential leukocyte was measured before surgery, and patients were followed-up 3.6 years later. The primary end point was all-cause mortality. Results: The preoperative N/L ratio was a powerful univariable predictor of mortality (hazard ratio [HR] 1.13 per unit, P 3.36). Conclusion: An elevated N/L ratio is associated with a poorer survival after CABG. This prognostic utility is independent of other recognized risk factors.Peer reviewedAuthor versio

An evaluation: The potential of discarded tires as a source of fuel

The destructive distillation of rubber tire samples was studied by thermogravimetry, differential scanning calorimetry, combustion calorimetry, and mass spectroscopy. The decomposition reaction was found to be exothermic and produced a mass loss of 65 percent. The gas evolution curves that were obtained indicate that a variety of organic materials are evolved simultaneously during the decomposition of the rubber polymer