14,868 research outputs found
Synthesis and analysis of jet fuels from shale oil and coal syncrudes
The technical problems involved in converting a significant portion of a barrel of either a shale oil or coal syncrude into a suitable aviation turbine fuel were studied. TOSCO shale oil, H-Coal and COED coal syncrudes were the starting materials. They were processed by distillation and hydrocracking to produce two levels of yield (20 and 40 weight percent) of material having a distillation range of approximately 422 to 561 K (300 F to 550 F). The full distillation range 311 to 616 K (100 F to 650 F) materials were hydrotreated to meet two sets of specifications (20 and 40 volume percent aromatics, 13.5 and 12.75 weight percent H, 0.2 and 0.5 weight percent S, and 0.1 and 0.2 weight percent N). The hydrotreated materials were distilled to meet given end point and volatility requirements. The syntheses were carried out in laboratory and pilot plant equipment scaled to produce thirty-two 0.0757 cu m (2-gal)samples of jet fuel of varying defined specifications. Detailed analyses for physical and chemical properties were made on the crude starting materials and on the products
Observation of a resonant four-body interaction in cold cesium Rydberg atoms
Cold Rydberg atoms subject to long-range dipole-dipole interactions represent
a particularly interesting system for exploring few-body interactions and
probing the transition from 2-body physics to the many-body regime. In this
work we report the direct observation of a resonant 4-body Rydberg interaction.
We exploit the occurrence of an accidental quasi-coincidence of a 2-body and a
4-body resonant Stark-tuned Forster process in cesium to observe a resonant
energy transfer requiring the simultaneous interaction of at least four
neighboring atoms. These results are relevant for the implementation of quantum
gates with Rydberg atoms and for further studies of many-body physics.Comment: 5 pages, 5 figure
Solar Flare X-ray Source Motion as a Response to Electron Spectral Hardening
Context: Solar flare hard X-rays (HXRs) are thought to be produced by
nonthermal coronal electrons stopping in the chromosphere, or remaining trapped
in the corona. The collisional thick target model (CTTM) predicts that sources
produced by harder power-law injection spectra should appear further down the
legs or footpoints of a flare loop. Therefore, hardening of the injected
power-law electron spectrum during flare onset should be concurrent with a
descending hard X-ray source.
Aims: To test this implication of the CTTM by comparing its predicted HXR
source locations with those derived from observations of a solar flare which
exhibits a nonthermally-dominated spectrum before the peak in HXRs, known as an
early impulsive event.
Methods: HXR images and spectra of an early impulsive C-class flare were
obtained using the Ramaty High-Energy Solar Spectroscopic Imager (RHESSI).
Images were reconstructed to produce HXR source height evolutions for three
energy bands. Spatially-integrated spectral analysis was performed to isolate
nonthermal emission, and to determine the power-law index of the electron
injection spectrum. The observed height-time evolutions were then fit with
CTTM-based simulated heights for each energy.
Results: A good match between model and observed source heights was reached,
requiring a density model that agreed well with previous studies of flare loop
densities.
Conclusions: The CTTM has been used to produce a descent of model HXR source
heights that compares well with observations of this event. Based on this
interpretation, downward motion of nonthermal sources should indeed occur in
any flare where there is spectral hardening in the electron distribution during
a flare. However, this would often be masked by thermal emission associated
with flare plasma pre-heating.Comment: 8 pages, 5 figure
Fatigue life estimates for helicopter loading spectra
Helicopter loading histories applied to notch metal samples are used as examples, and their fatigue lives are calculated by using a simplified version of the local strain approach. This simplified method has the advantage that it requires knowing the loading history in only the reduced form of ranges and means and number of cycles from the rain-flow cycle counting method. The calculated lives compare favorably with test data
Technology for satellite power conversion
The work is this reporting period was concentrated on electronically calibrating the bolometer detectors. The calibration is necessary for two reasons: first, the power delivered to the rectifying circuit must be known in order to choose a diode with the appropriate barrier height, and second, the power captured by the antenna must be measured if the efficiency of the rectenna is to be divided into antenna efficiency and rectification efficiency. The millimeter wave region operation of the bolometers was simulated with a VHF (10 to 90 MHz) test signal. These detectors are accurate to within roughly 10%. The typical responsivity of the bolometers is 10 volts/watt and the NEP at 20 Hz is 5 times 10 to the minus 9th power W(Hz)-1/2
Technology for satellite power conversion
The work performed in this reporting period has concentrated on the metal-oxide-metal (MOM) diode. The fabrication procedure begins with the deposition of gold probing pads to provide a non-oxidizing contact to test the dc characteristics to the diode accurately. A thin patch capped with an insulating SiO2 layer, is deposited next to form the first half of the diode. The other half of the diode, typically Ni, is deposited completing the conduction path from the oxidized edge of the Ni patch to the opposite gold probing pad. It is important in this step that the last metallization take place without exposing the newly oxidized surface to the atmosphere. Successful production of diodes has been achieved. Work on millimeter wave frequency rectennas incorporating known semiconductor diode technology has been initiated
Technology for satellite power conversion
Components were examined that will be needed for high frequency rectenna devices. The majority of the effort was spent on measuring the directivity and efficiency of the half-wave dipole antenna. It is felt that the antenna and diode should be roughly optimized before they are combined into a rectenna structure. An integrated low pass filter had to be added to the antenna structure in order to facilitate the field pattern measurements. A calculation was also made of the power density of the Earth's radiant energy as seen by satellites in Earth orbit. Finally, the feasibility of using a Metal-Oxide-Metal (MOM) diode for rectification of the received power was assessed
Half Cycle Pulse Train Induced State Redistribution of Rydberg Atoms
Population transfer between low lying Rydberg states independent of the
initial state is realized using a train of half-cycle pulses with pulse
durations much less than the classical orbit period. We demonstrate
experimentally the transfer of population from initial states around n=50 down
to n<40 as well as up to the continuum. The measured population transfer
matches well to a model of the process for 1D atoms.Comment: V2: discussion extended, version accepted for publication in Physical
Review
Strongly correlated gases of Rydberg-dressed atoms: quantum and classical dynamics
We discuss techniques to generate long-range interactions in a gas of
groundstate alkali atoms, by weakly admixing excited Rydberg states with laser
light. This provides a tool to engineer strongly correlated phases with reduced
decoherence from inelastic collisions and spontaneous emission. As an
illustration, we discuss the quantum phases of dressed atoms with dipole-dipole
interactions confined in a harmonic potential, as relevant to experiments. We
show that residual spontaneous emission from the Rydberg state acts as a
heating mechanism, leading to a quantum-classical crossover.Comment: 4 pages, 4 figure
- …