37 research outputs found
Some poınts to be consıdered ın the usage and machınıng of coated board products
Bu çalışmada; kaplanmış levhaların özellikleri, levhalarda bakım, taşıma, depolama ve temizlik ile levhaların işlenmesinde dikkat edilmesi gereken bazı hususlar incelenmiştir.: In this study, properties of the coated boards, packaging, transportation, storage, cleaning on the boards and some points to be considered for the machining of the boards were investigated
Türkiye Yongalevha Endüstrisinin Üretim Problemleri Ve Çözüm Önerilerinin İncelenmesi
Bu çalışmada orman ürünleri sanayi içerisinde önemli bir yeri olan ve birçok farklı sektöre hammadde olarak kullanılan yongalevhanın üretim aşamasında karşılaşılan sorunların tespit edilmesi ve sektörün bu sorunların çözümünde ortaya koyduğu çözüm yaklaşımlarının incelenmesi amaçlanmıştır. Tüketicilerin yongalevhadan beklediği kalite özelliklerinin de belirlenmesi bir diğer amacı oluşturmaktadır. Bu amaçlarla hazırlanan anket formu Türkiye genelinde yongalevha üretimi yapan tesis üretim sorumlularına uygulanmıştır. Çalışma sonucunda tüketici kalite beklentileri, yongalevha üretiminde karşılaşılan sorunların sıklık düzeyleri ve öncelik sıralamaları ile sorunlara ilişkin çözüm önerileri ortaya koyulmuştur. Müşterilerden gelen en önemli beklentinin düşük fiyat ve hızlı teslimat olduğu ifade edilmiştir. Yongalevha üretiminde ortaya çıkan en önemli sorunların ondülasyon ve gözenekli yüzey oluşumu olduğu tespit edilmiştir
Determınatıon of suıtabılıty of douglas-fır (pseudotsuga menziesii (mirb.) franco) specıes for partıcleboard productıon
Bu çalışmada, hızlı büyüyen ağaç türlerinden biri olan ve Trabzon’un Maçka bölgesinde başarılı plantasyon sonuçları veren Douglas Göknarı (Pseudotsuga menziesii (Mirb.) Franco)’nın yonga levha üretimine uygunluğu araştırılmıştır. Üretilen levhaların fiziksel (şişme oranı, yoğunluk) ve mekanik özellikleri (eğilme direnci, yüzeye dik çekme direnci ve elastiklik modülü) belirlenmiştir. Pres sıcaklığı ile presleme süresinin ve levha yoğunluğunun yonga levha özellikleri üzerine etkileri araştırılmıştır. Elde edilen sonuçlar EN standartlarında öngörülen değerler ile karşılaştırılmıştır. Test sonuçlarına göre 0.70 g/cm3 yoğunlukta üretilen yonga levhalar EN standartlarında öngörülen minimum eğilme ve yüzeye dik çekme direnci ihtiyacını karşılamışlardır. Yoğunluğu 0.60 g/cm3 olan levhalar ise standartlarda öngörülen eğilme ve yüzeye dik çekme direnci değerlerine ulaşabilmek için 150 °C pres sıcaklığında ve 7 dakika presleme süresi kullanılarak üretilmelidir. Douglas Göknarı (Pseudotsuga menziesii (Mirb.) Franco)’ndan üretilen yonga levhaların şişme oranları standartlarda öngörülen değerlerden yüksek bulunmuştur. Bu nedenle bu levhaların kalınlığına şişme oranlarını azaltıcı ek bir çalışmanın yapılması gerektiği sonucuna ulaşılmıştır.In this study, Douglas-Fir (Pseudotsuga menziesii (Mirb.) Franco), one of the fast growing trees and planted succesfully in Maçka, Trabzon area was investigated for manufacturing particleboard. All panels were tested for physical property (thickness swelling (TS), density (D)) and mechanical properties (bending strength (BS), internal bond (IB), and modulus of elasticity (MOE)). The effects of press temperature, press time and board density on the some properties of particleboards were investigated. The results were compared with EN standard values. Results showed that Douglas-Fir particleboards produced at 0.70 g/cm3 density had the requirements of IB and BS. The particleboards which have 0.60 g/cm3 board density, needed 150 °C press temperature, 7 min. press time, respectively. In these production conditions, the particleboards had the required level of IB and BS according to the EN standards. But, TS values were higher than the required levels of the standard. For this reason, additional work is needed to improve the thickness swelling of Douglas-Fir particleboards
Análisis comparativo del impacto, de la segregación de los datos por género, en los protocolos de investigación de fisiología reproductiva y cardio-respiratoria
Es un hecho conocido que el dimorfismo sexual se presenta en la mayoría de las
especies animales. Las diferencias que esto conlleva, tienen una base genética que sustenta
características físicas propias de machos o hembras. Conocido esto, es evidente la necesidad de
determinar la incidencia genérica en el funcionamiento de cualquier organismo. Sin embargo, el
presente análisis, ha permitido comprobar que, la inclusión en la segregación de los resultados
por género en estudios de Bio-Medicina (clínicos y pre-clínicos) aún no es algo generalizado.
Para ello, se han revisado y combinado los resultados de un conjunto de estudios (fechados
entre 2011 y 2017) escogiéndose dos áreas (en cuyas fisio-patologías se acepte diferente grado
de impacto del género): aparato reproductivo y el sistema cardio-respiratorio. Los resultados
obtenidos confirman la necesidad de concienciar a la comunidad científica de la importancia de
la inclusión de la variable “género” en este tipo de estudios.It is a known fact that sexual dimorphism occurs in most animal species. The differences that this
entails have a genetic basis that supports physical characteristics of males or females. Once this
is known, the need to determine the generic incidence in the functioning of any organism is
evident. However, the present analysis has shown that inclusion in the segregation of results by
gender in Bio-Medicine studies (clinical and pre-clinical) is not yet widespread. For that, the
results of a series of studies (dated between 2011 and 2017) have been reviewed and combined,
choosing two areas (in whose physio-pathologies a different degree of gender impact is
accepted): reproductive system and the cardio-respiratory system. The results obtained confirm
the need to make the scientific community aware of the importance of including the gender
variable in this type of studies
The influence of raw material growth region, anatomical structure and chemical composition of wood on the quality properties of particleboards
In the present study, the impact of raw material grown region on the physical, mechanical, surface properties and formaldehyde emission of the particleboard was investigated. Ailanthus altissima wood grown in Trabzon had longer fiber length and thicker fiber and trachea cell wall than those of the wood grown in Artvin. The highest amounts of lignin, ash, condensed tannin and solubility values were found in wood grown in Artvin. Ailanthus altissima wood grown in Trabzon had higher amounts of cellulose and hemicellulose than those of the wood grown in Artvin. Particleboards made from wood grown in Artvin had worse surface quality and mechanical strength properties than those of panels made from wood grown in Trabzon. On the other hand, the results showed that particleboards produced from wood grown in Artvin had lower thickness swelling and formaldehyde emision values than those of the panels produced from wood grown in Trabzon
The quality comparison of particleboards produced from heartwood and sapwood of european larch
In this paper, the impacts of heartwood and sapwood usage on the physical, mechanical, and surface properties and formaldehyde emission of particleboard are investigated. European Larch (Larix decidua) trees are chosen as a raw material. The logs are divided into three segments: sapwood, heartwood and total wood. The highest amounts of cellulose (51.54%), and hemicelluloses (22.24%) in the sapwood, followed by total wood, and the heartwood, respectively. However, the highest amount of lignin (30.54%) was found in the heartwood. The highest extractives values are obtained from heartwood, followed by total wood, and the sapwood, respectively. While the lowest pH value (3.03) is found in heartwood, the sapwood samples provide the highest values (4.95). The highest ash (0.49%) content and amount of condensed tannin (13.89%) are extracted from heartwood, followed by total wood, and sapwood, respectively. The test panels manufactured from sapwood have the smoothest surface (7.49 µm (Ra), 48.86 µm (Ry), and 35.12 µm (Rz)) and the lowest contact angles (67.8ᵒ), while the roughest surface (14.20 µm (Ra), 68.05 µm (Ry), and 50.02 µm (Rz)) and highest contact angle (96.9ᵒ) are obtained from the panels of heartwood. The thickness swelling (19.88%) and formaldehyde emission (7.28%) values of the panels manufactured from heartwood are significantly lower than the panels manufactured from the total wood and sapwood. The highest modulus of rupture (MOR), modulus of elasticity (MOE), and internal bond (IB) values are observed on sapwood, respectively, 15.60 MPa (MOR), 2201 MPa (MOE), and 0.523 MPa (IB). These mechanical strength values (MOR, MOE, and IB) are followed by total wood, and the heartwood, respectively. Surface smoothness and wettability of the particleboards manufactured from sapwood are better than those of total wood and heartwood
The ınfluences of moısture content of the partıcle, paraffın usage and wood specıes on the some technologıcal propertıes of artıcleboard
Bu çalışmada tutkallama öncesi yonga rutubeti, parafin kullanımı ve ağaç cinsinin yongalevhanın fiziksel (yoğunluk profili, kalınlık artışı), mekanik (eğilme direnci, elastikiyet modülü, yüzeye dik çekme direnci) ve yüzey kalitesi (yüzey pürüzlülüğü) üzerine etkileri araştırılmıştır. Yapılan çalışmalar sonucu; dış tabaka yonga rutubetinin yükseltilmesi levhanın tüm özelliklerini iyileştirmiştir. Dış tabakalarında kavak odunu kullanılan yongalevhalarda en yüksek kalite değerlerine ulaşılmıştır. Parafin kullanımı yüzey düzgünlüğünü artırmıştır.In this study; the influences of moisture content of the particle before blending, paraffin usage and wood species on the physical (density profile, thickness swelling), mechanical (modulus of rupture, modulus of elasticity, internal bond strength) and surface quality (surface roughness) of particleboard were investigated. According to the test results; increasing moisture content of the surface layer particles improved the all of the properties of the panels. Particleboards consisting poplar particles in the surface layers had the highest quality values. Paraffin usage increased the surface smoothness
Influence of press type on the technologıcal propertıes of partıcleboard
Bu çalışmada 280x210x1.8 cm boyutlarında, 0.68 g/cm3 yoğunlukta, üre formaldehit tutkalı kullanılarak yatık preslenmiş yonga levhalar üretilmiştir. Yonga levhaların preslenmesinde sürekli (kontinyu) ve klasik (katlı) olmak üzere iki çeşit pres makinesi kullanılmıştır. Üretilen levhaların eğilme direnci, elastiklik modülü, yüzeye dik çekme direnci, vida tutma gücü ve 24 saatte kalınlığına şişme oranları belirlenmiştir. Yapılan deneyler sonucu pres çeşidinin yonga levha teknik özellikleri üzerinde etkili olduğu saptanmıştır.In is study, particleboard produced in 280x210x1.8 cm dimensions, at 0.68 g/cm3 density with using urea formaldehyde adhesive. For the pressing of the boards, classic press (discontinue) and continue press were used. Static bending strength, modulus of elasticity, internal bond, screw holding and thickness swelling in 24 h immersion were recorded during the experiments. It was stated that press type affected the technological properties of particleboar
Desıgn alternatıves on the lamınates
Odun esaslı levha üreticileri her geçen gün artan oranlarda laminat malzeme kullanmaktadır. Laminat malzemeler su, rutubet, çizilme, aşınma, yanma ve kimyasal maddelere karşı dayanıklıdır. Bu malzemeler ısı etkisiyle sertleşen tutkallarla doyurulmuş baskılı dekoratif kağıtları içermektedir. Bu çalışmada; laminat türleri, bileşimi ve dizayn seçenekleri incelenmiştir.Wood based panel manufacturers use increasing volumes of laminates. Laminates are resistant to the water, humidity, scratch, abrasion, burning and chemicals. These products consist of printed decor papers that have been saturated with thermosetting resin. In this study, laminate types, composition form and design alternatives were investigated
Possibilities of Using Sunflower Tray in Particleboard Industry
Bu çalışmada, ayçiçek üretimi sonrası tarlada atık kalan ayçiçek tablasının hammadde olarak yonga levha üretimine
uygunluğu araştırılmıştır. Çalışmada belirli oranlarda kokar ağaç (Ailanthus altissima (Mill.) Swingle) odunu ve
ayçiçek tablası içeren 5 farklı levha üretilmiştir. Aynı zamanda kullanılan hammaddelerin kimyasal özellikleri ve
yonga levhaların çeşitli kalite özelliklerine de (fiziksel, mekanik, yüzey özellikleri ve formaldehit emisyonu)
bakılmıştır. Son olarak da elde edilen veriler değerlendirilerek yonga levhaların çeşitli kullanım yerlerinde özellikle
de mobilya ve genel kullanım için uygunluğu ilgili standartlara bakılarak değerlendirilmiştir. Kimyasal analizlerden
elde edilen verilen verilerin değerlendirilmesi sonucunda tüm çözünürlük değerleri, pH ve kül değerlerinin ayçiçek
tablasında kokar ağaca odununa göre daha yüksek olduğu belirlenmiştir. Fakat holoselüloz, selüloz, hemizelüloz ve
lignin miktarlarının ise kokar ağaç odununda ayçiçek tablasına göre daha yüksek olduğu tespit edilmiştir. Yapılan
çalışmalardan elde edilen verilerin istatistiksel olarak değerlendirilmesi sonucu yonga levhaların üretiminde % 10
ayçiçek kafası kullanılması yonga levhaların teknolojik özelliklerini etkilememiştir. % 20, % 30 ve % 100 ayçiçek
tablası kullanımı eğilme direnci, elastikiyet modülü ve yüzeye dik çekme direncini olumsuz yönde etkilemiştir. Buna
rağmen 2 ve 24 saatlik kalınlığına şişme değerleri ve formaldehit emisyonunu ise olumlu yönde etkilemiştir. Son
olarak ise levhaların yüzey özelliklerine (ortalama pürüzlülük, en büyük pürüzlülük ve on nokta pürüzlülüğü)
bakıldığında ayçiçek tablası kullanım oranın artmasına paralel olarak pürüzlülük değerlerinin arttığı tespit edilmiştir.In this study, the appropriateness of the remaining sunflower tray in the field after the sunflower production as raw
material to the particleboard production was investigated. In the study, 5 different particleboards were produced,
which included certain amounts of wood of tree of heaven (Ailanthus altissima (Mill.) Swingle) and sunflower table.
At the same time, the chemical properties of the raw materials used and the various quality characteristics of the
chips (physical, mechanical, surface properties and formaldehyde emission) were examined. Finally, the obtained
data were evaluated and evaluated for the suitability of the chipboards in various places of use, in particular for
furniture and general use, according to relevant standards. As a result of the evaluation of the data obtained from
chemical analysis, it has been determined that all the solubility values, pH and ash values are higher in the sunflower
tray than the wood of tree of heaven. However, the amount of holocellulose, cellulose, hemisellulose and lignin were
found to be higher in the wood of tree heaven compared to the sunflower tray. The statistical evaluation of the data
obtained as a result of the studies done does not affect the technological characteristics of the chips by using 10%
sunflower head in the production of the particleboards. Using 20%, 30% and 100% sunflower tray affected the
bending strength, modulus of elasticity, and internal bond strenght to the surface in the negative direction. Despite
this, it affected positively the thickness swelling values for 2 and 24 hour immersion and formaldehyde
emission..Finally, when looking at the surface properties of the boards (average roughness, maximum roughness and
ten point roughness), it was determined that the roughness values increased in parallel with the increase of sunflower
tray utilization rate