Bu çalışmada, ayçiçek üretimi sonrası tarlada atık kalan ayçiçek tablasının hammadde olarak yonga levha üretimine
uygunluğu araştırılmıştır. Çalışmada belirli oranlarda kokar ağaç (Ailanthus altissima (Mill.) Swingle) odunu ve
ayçiçek tablası içeren 5 farklı levha üretilmiştir. Aynı zamanda kullanılan hammaddelerin kimyasal özellikleri ve
yonga levhaların çeşitli kalite özelliklerine de (fiziksel, mekanik, yüzey özellikleri ve formaldehit emisyonu)
bakılmıştır. Son olarak da elde edilen veriler değerlendirilerek yonga levhaların çeşitli kullanım yerlerinde özellikle
de mobilya ve genel kullanım için uygunluğu ilgili standartlara bakılarak değerlendirilmiştir. Kimyasal analizlerden
elde edilen verilen verilerin değerlendirilmesi sonucunda tüm çözünürlük değerleri, pH ve kül değerlerinin ayçiçek
tablasında kokar ağaca odununa göre daha yüksek olduğu belirlenmiştir. Fakat holoselüloz, selüloz, hemizelüloz ve
lignin miktarlarının ise kokar ağaç odununda ayçiçek tablasına göre daha yüksek olduğu tespit edilmiştir. Yapılan
çalışmalardan elde edilen verilerin istatistiksel olarak değerlendirilmesi sonucu yonga levhaların üretiminde % 10
ayçiçek kafası kullanılması yonga levhaların teknolojik özelliklerini etkilememiştir. % 20, % 30 ve % 100 ayçiçek
tablası kullanımı eğilme direnci, elastikiyet modülü ve yüzeye dik çekme direncini olumsuz yönde etkilemiştir. Buna
rağmen 2 ve 24 saatlik kalınlığına şişme değerleri ve formaldehit emisyonunu ise olumlu yönde etkilemiştir. Son
olarak ise levhaların yüzey özelliklerine (ortalama pürüzlülük, en büyük pürüzlülük ve on nokta pürüzlülüğü)
bakıldığında ayçiçek tablası kullanım oranın artmasına paralel olarak pürüzlülük değerlerinin arttığı tespit edilmiştir.In this study, the appropriateness of the remaining sunflower tray in the field after the sunflower production as raw
material to the particleboard production was investigated. In the study, 5 different particleboards were produced,
which included certain amounts of wood of tree of heaven (Ailanthus altissima (Mill.) Swingle) and sunflower table.
At the same time, the chemical properties of the raw materials used and the various quality characteristics of the
chips (physical, mechanical, surface properties and formaldehyde emission) were examined. Finally, the obtained
data were evaluated and evaluated for the suitability of the chipboards in various places of use, in particular for
furniture and general use, according to relevant standards. As a result of the evaluation of the data obtained from
chemical analysis, it has been determined that all the solubility values, pH and ash values are higher in the sunflower
tray than the wood of tree of heaven. However, the amount of holocellulose, cellulose, hemisellulose and lignin were
found to be higher in the wood of tree heaven compared to the sunflower tray. The statistical evaluation of the data
obtained as a result of the studies done does not affect the technological characteristics of the chips by using 10%
sunflower head in the production of the particleboards. Using 20%, 30% and 100% sunflower tray affected the
bending strength, modulus of elasticity, and internal bond strenght to the surface in the negative direction. Despite
this, it affected positively the thickness swelling values for 2 and 24 hour immersion and formaldehyde
emission..Finally, when looking at the surface properties of the boards (average roughness, maximum roughness and
ten point roughness), it was determined that the roughness values increased in parallel with the increase of sunflower
tray utilization rate