The impact of tool selection on back and wrist injury risk in tying steel reinforcement bars: a single case experiment

The paper explores the risk of work-related musculoskeletal injury in tying steel reinforcement bars. Three tools are compared to determine the extent to which ergonomic tools can reduce the risk of injury to the back and wrist in steel-tying. A whole body system of wearable sensors was used to measure biomechanical risk in tying. Three tools were assessed to determine their impact on the risk of work-related musculoskeletal injury when used at different heights. These were: a conventional pincer-cutting tool; a power-driven tying tool, and a long handled stapler tool. No tool was found to work best in all situations. The long handled stapler tool significantly reduced trunk inclination when used from ground to shoulder height, but produced higher trunk extension (backward bending) when used above shoulder height. The power tying tool did not reduce the need to bend when working at lower work heights. The power-tying tool produced significantly lower peak wrist flexion values compared to the conventional pincer-cutter tool at all work heights except overhead. The power tying tool involved significantly lower levels of wrist rotation than the conventional pincer-cutter tool at all work heights above knee level. Many assessments of ergonomic risk factors in construction rely on observational methods. The use of small, lightweight wearable sensors permits the objective measurement of biomechanical risk factors for work-related musculoskeletal injury, as well as providing objective performance data that can be used in the design and selection of task-specific tools. Our analysis of work by height also provides insight into the way in which risk factors and reduction opportunities afforded by different tools vary depending on the height at which work is to be performed

New Quaternary geochronometric constraints on river incision in the Virginia Piedmont: Relative contributions of climate, base-level fall, knickpoint retreat, and active tectonics

River terraces are fluvial landforms that represent flood plains abandoned through river incision and, when accurately correlated and dated, can serve as paleogeodetic markers, indicating the elevation and location of past channels and the subsequent fluvial and tectonic processes shaping the landscape. Fluvial terraces are most useful when the incision processes that caused their abandonment and formation are better understood. This thesis studies river incision reconstructed from fluvial terraces of the South Anna River in the central Virginia Piedmont, USA. The South Anna River flows directly above an active fault, on which large, but infrequent seismic events have occurred, and the most recent event was the 23 August 2011 Mineral earthquake. Two conceptual incision models are tested to better understand the fluvial response to active tectonics in this region: 1) spatially-uniform vertical incision and 2) diachronous horizontal knickpoint retreat. Here, terraces and incision were evaluated in the context of a 1:24,000 scale surficial map of alluvial deposits, optically stimulated luminescence (OSL) and infrared luminescence (IRSL) geochronology, and knickpoint celerity modeling. The South Anna River and its tributaries traverse across the geologic, topographic and structural grain of central Virginia Piedmont, USA, a region known for Late Cenozoic base-level fall, high amplitude climate changes, and historic seismicity. Litho- and pedostratigraphically correlative deposits are found to form five groups of terraces (Qt1-Qt5) with similar, but not exact relative elevations above modern channel. Within these groups, the terraces have similar OSL/IRSL ages that do not systematically decrease in age upstream towards knickpoint in the modern channel. Similarly, the modeled rate of knickpoint retreat through the South Anna channel of ~7-14km/Ma is too slow to explain the time-transgressive OSL/IRSL dates for any terrace group. Terrace formation by knickpoint migration and horizontal floodplain abandonment is rejected as a dominant process in terrace formation, in favor of more spatially-uniform vertical incision. In this landscape, the OSL/IRSL results suggest that flood plains are widened and then are abandoned and become terraces as the South Anna channel responds to climatically-driven unsteady changes in discharge and sediment yield. The complex age-elevation relationships of terraces proximal to epicenter of the 23 August 2011 Mineral earthquake argue for a terrace correlation that allows for rock uplift consistent with the co-seismic response of the 2011 Mineral earthquake

The impact of tool selection on back and wrist injury risk in tying steel reinforcement bars: a single case experiment

The paper explores the risk of work-related musculoskeletal injury in tying steel reinforcement bars. Three tools are compared to determine the extent to which ergonomic tools can reduce the risk of injury to the back and wrist in steel-tying. A whole body system of wearable sensors was used to measure biomechanical risk in tying. Three tools were assessed to determine their impact on the risk of work-related musculoskeletal injury when used at different heights. These were: a conventional pincer-cutting tool; a power-driven tying tool, and a long handled stapler tool. No tool was found to work best in all situations. The long handled stapler tool significantly reduced trunk inclination when used from ground to shoulder height, but produced higher trunk extension (backward bending) when used above shoulder height. The power tying tool did not reduce the need to bend when working at lower work heights. The power-tying tool produced significantly lower peak wrist flexion values compared to the conventional pincer-cutter tool at all work heights except overhead. The power tying tool involved significantly lower levels of wrist rotation than the conventional pincer-cutter tool at all work heights above knee level. Many assessments of ergonomic risk factors in construction rely on observational methods. The use of small, lightweight wearable sensors permits the objective measurement of biomechanical risk factors for work-related musculoskeletal injury, as well as providing objective performance data that can be used in the design and selection of task-specific tools. Our analysis of work by height also provides insight into the way in which risk factors and reduction opportunities afforded by different tools vary depending on the height at which work is to be performed

Home furnishings I : accessories for the girl's room

Includes bibliographical references (page 16)

Home furnishings II : units for the bedroom

Cooperative Extension Work in Agriculture and Home Economics, University of Missouri, College of Agriculture and the United States Department of Agriculture cooperating."March, 1939."Includes bibliographical references (page 30).Title from cover.Includes bibliographical references (page 30)

Payout Policy in the 21st Century

We survey 384 CFOs and Treasurers, and conduct in-depth interviews with an additional two dozen, to determine the key factors that drive dividend and share repurchase policies. We find that managers are very reluctant to cut dividends, that dividends are smoothed through time, and that dividend increases are tied to long-run sustainable earnings but much less so than in the past. Rather than increasing dividends, many firms now use repurchases as an alternative. Paying out with repurchases is viewed by managers as being more flexible than using dividends, permitting a better opportunity to optimize investment. Managers like to repurchase shares when they feel their stock is undervalued and in an effort to affect EPS. Dividend increases and the level of share repurchases are generally paid out of residual cash flow, after investment and liquidity needs are met. Financial executives believe that retail investors have a strong preference for dividends, in spite of the tax disadvantage relative to repurchases. In contrast, executives believe that institutional investors as a class have no strong preference between dividends and repurchases. In general, management views provide at most moderate support for agency, signaling, and clientele hypotheses of payout policy. Tax considerations play only a secondary role. By highlighting where the theory and practice of corporate payout policy are consistent and where they are not, we attempt to shed new light on important unresolved issues related to payout policy in the 21st century.

Improving the medical school–residency transition

Peer Reviewedhttps://deepblue.lib.umich.edu/bitstream/2027.42/138225/1/tct12576_am.pdfhttps://deepblue.lib.umich.edu/bitstream/2027.42/138225/2/tct12576.pd