Efficacy and cytotoxicity of binary mixtures as root canal filling solvents

Objectives: This study reports the efficacy of two solvent mixtures on the dissolution of gutta-percha and AH Plus sealer, together with the cytotoxicity. Methods: Methyl ethyl ketone (MEK), orange oil, tetrachloroethylene, MEK/tetrachloroethylene (1:1), MEK/orange oil (1:1), and chloroform (control) were tested. Twelve groups (n = 15) of standardized stainless-steel molds filled with softened gutta-percha cones and twelve (n = 15) filled with AH Plus were immersed in the corresponding mixture or individual solvent, in an ultrasonic bath, for either 2 or 5 min. The effect of the solvents was assessed qualitatively by a topographical analysis (scanning electron microscopy) and chemical analysis (Fourier transform infrared spectroscopy), and quantitatively by a weight loss and viscoelastic property (dynamic mechanical analysis) evaluation. The cytotoxicity was assessed on MG63 human osteoblastic cells. Results: The mixtures did not show the formation of new compounds. Both presented significantly higher efficacies compared to their individual solvents, suggesting a synergistic effect. Their dissolution efficacy was similar to that of chloroform, showing high cytocompatibility. Conclusions: The proposed strategy, incorporating ultrasound agitation and profiting from the synergy of adequate solvents, might enhance root canal cleanliness allowing a single-step procedure to dissolve gutta-percha and the sealer remnants, while assuring cytocompatibility with the periapical tissues.This article was supported by National Funds through FCT—Fundação para a Ciência e a Tecnologia,I.P.-V., within CINTESIS, R & D Unit (reference UIDB/4255/2020)

Development of poly(l-Lactic Acid)-based bending actuators

This work reports on the development of bending actuators based on poly(l-lactic acid) (PLLA)/ionic liquid (IL) blends, through the incorporation of 40% wt. of the 1-ethyl-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Emim][TFSI]) IL. The films, obtained by solvent casting at room temperature and 50 °C, were subjected to several post-thermal treatments at 70, 90, 120 and 140 °C, in order to modify the crystallinity of the films. The influence of the drying temperature and of [Emim][TFSI] blending on the morphological, structural, mechanical and electrical properties of the composite materials were studied. The IL induced the formation of a porous surface independently of the processing conditions. Moreover, the [Emim][TFSI] dopant and the post-thermal treatments at 70 °C promoted an increase of the degree of crystallinity of the samples. No significant changes were observed in the degree of crystallinity and Young Modulus for samples with thermal treatment between 70 and 140 °C. The viability of the developed high ionic conductive blends for applications as soft actuators was evaluated. A maximum displacement of 1.7 mm was achieved with the PLLA/[Emim][TFSI] composite prepared at 50 °C and thermally treated at 140 °C, for an applied voltage of 10 Vpp, at a frequency of 100 mHz. This work highlights interesting avenues for the use of PLLA in the field of actuators.The authors thank the FCT—Fundação para a Ciência e Tecnologia—for financial support under the Strategic Funding UID/FIS/04650/2020, and PEST-C/QUI/UIO686/2019, the Associated Laboratory Research Unit for Green Chemistry, Technologies and Clean Processes, LAQV (financed by national funds from FCT/MEC, UID/QUI/50006/2020 and ERDF under the PT2020, POCI-01-0145-FEDER-007265) and projects PTDC/BTM-MAT/28237/2017 and PTDC/EMD-EMD/28159/2017. DMC and LCF also thank the grants SFRH/BPD/121526/2016 and SFRH/BD/145345/2019, respectively

Erratum: Development of Poly(l-Lactic Acid)-Based Bending Actuators. Polymers 2020, 12, 1187

The authors wish to make a change to their published paper [1]. In the original manuscript, there is a mistake in a sentence in Section 3.5, on page 10. Two words “anions and cations” were reverted by mistake. The corrected sentence is shown below: The strain developed as a response to the applied electrical field results from the diffusion of the ions and migration to the positive (anions) and negative (cations) electrode layers, and subsequent accumulation close to the electrodes. The authors apologize for any inconvenience caused, and the change does not affect the scientific results. The manuscript will be updated, and the original will remain online on the article webpage at https://www.mdpi.com/2073-4360/12/5/1187.(undefined

Multifunctional magnetoelectric sensing and bending actuator response of polymer-based hybrid materials with magnetic ionic liquids

With the evolution of the digital society, the demand for miniaturized multifunctional devices has been increasing, particularly for sensors and actuators. These technological translators allow successful interaction between the physical and digital worlds. In particular, the development of smart materials with magnetoelectric (ME) properties, capable of wirelessly generating electrical signals in response to external magnetic fields, represents a suitable approach for the development of magnetic field sensors and actuators due to their ME coupling, flexibility, robustness and easy fabrication, compatible with additive manufacturing technologies. This work demonstrates the suitability of magnetoelectric (ME) responsive materials based on the magnetic ionic liquid (MIL) 1-butyl-3-methylimidazolium tetrachloroferrate ([Bmim][FeCl4]) and the polymer poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE) for magnetic sensing and actuation device development. The developed sensor works in the AC magnetic field and has frequency-dependent sensitivity. The materials show voltage responses in the mV range, suitable for the development of magnetic field sensors with a highest sensitivity (s) of 76 mV·Oe−1. The high ME response (maximum ME voltage coefficient of 15 V·cm−1·Oe−1) and magnetic bending actuation (2.1 mm) capability are explained by the magnetoionic (MI) interaction and the morphology of the composites.This work was supported by the Portuguese Foundation for Science and Technology (FCT) in the framework of the Strategic Funding UID/FIS/04650/2020, UID/QUI/00686/2020, LA/P/0008/2020, UIDB/50006/2020 and UIDP/50006/2020. The authors are grateful for funds through FCT under the projects 2022.05932.PTDC, PTDC/BTM-MAT/28237/2017 and PTDC/EMD-EMD/28159/2017 and grant SFRH/BD/145345/2019 (L.C.F). D.M.C. and P.M. thank FCT—Fundação para a Ciência e Tecnologia for the contract under the Stimulus of Scientific Employment, Individual Support 2020.02915.CEECIND and CEECIND/03975/2017, respectively. This study forms part of the Advanced Materials programme and was supported by MCIN with funding from European Union NextGenerationEU (PRTR-C17.I1) and by the Basque Government under the IKUR program. Funding from the Basque Government Industry Departments under the ELKARTEK program is also acknowledged. Technical and human support provided by IZO-SGI, SGIker (UPV/EHU, MICINN, GV/EJ, ERDF and ESF) is gratefully acknowledged

Electrospun magnetic ionic liquid based electroactive materials for tissue engineering applications

Functional electrospun fibers incorporating ionic liquids (ILs) present a novel approach in the development of active microenviroments due to their ability to respond to external magnetic fields without the addition of magnetic particles. In this context, this work reports on the development of magnetically responsive magneto-ionic fibers based on the electroactive polymer poly(vinylidene fluoride) and the magnetic IL (MIL), bis(1-butyl-3-methylimidazolium) tetrathiocyanatocobaltate ([Bmim]2[(SCN)4Co]). The PVDF/MIL electrospun fibers were prepared incorporating 5, 10 and 15 wt.% of the MIL, showing that the inclusion of the MIL increases the polar β-phase content of the polymer from 79% to 94% and decreases the crystallinity of the fibers from 47% to 36%. Furthermore, the thermal stability of the fibers decreases with the incorporation of the MIL. The magnetization of the PVDF/MIL composite fibers is proportional to the MIL content and decreases with temperature. Finally, cytotoxicity assays show a decrease in cell viability with increasing the MIL content.This research was funded by FCT—Fundação para a Ciência e Tecnologia (FCT) under the scope of the strategic funding of UID/FIS/04650/2020, and project PTDC/BTM-MAT/28237/2017. Moreover, the authors thank FCT for the research grant SFRH/BD/145345/2019 (LMC), SFRH/BD/148655/2019 (RMM), and D.M.C. and CR thank the FCT for the contract under the Stimulus of Scientific Employment 2020.02915.CEECIND and 2020.04163.CEECIND, respectively.The authors acknowledge funding by Spanish State Research Agency (AEI) and the European Regional Development Fund (ERFD) through the project PID2019-106099RB-C43/AEI/10.13039/501100011033 and from the Basque Government Industry Departments under the ELKARTEK program. Technical and human support provided by IZO-SGI, SGIker (UPV/EHU, MICINN, GV/EJ, ERDF and ESF) is gratefully acknowledged

Amination of polymeric braid structures to improve tendon healing: an experimental comparison

Several polymers are researched for tendon repair as polyethylene terephthalate (PET) and polylactic acid (PLA). These are biocompatible and useful in scaffolding repair though with minimal success due to long-term failure. There is a need to improve such scaffolds' design and physical–chemical nature. This work concerns surface functionalization of polymeric braids (PET and PLA) that fulfill the high mechanical demands of tissues such as tendons. The functionalization aims to incorporate amine groups in the braids' surface, improve cell adhesion, and consequently, the poor healing rate of these tissues and the biointegration of the braids. Two approaches are compared: the direct application of NH3 plasma and the surface grafting of EDA after O2 plasma activation. X-ray photoelectron spectroscopy (XPS) shows that amine groups are effectively introduced onto the samples' surfaces. Besides, the plasma parameters chosen do not compromise the topography and tensile behavior of the braids. Resazurin assay and scanning electron microscopy show that the NH3 treatment improves cell–biomaterial interaction as improved cell adhesion and proliferation are observed. Both approaches are safe for biomedical applications. The NH3 plasma approach is more environmentally friendly, faster, and easier to scale-up, showing potential for application in the final hybrid medical devicepublishe

Environmentally friendly carrageenan-based ionic-liquid driven soft actuators

UID/FIS/04650/2020 UID/QUI/0686/2020 LA/P/0008/2020 PID2019-106099RB-C43/AEI/10.13039/501100011033A naturally derived polymer based on iota carrageenan and different ammonium and imidazolium based ionic liquids (ILs) are used for the development of environmentally friendly soft actuators. The influence of IL content and type and solvent evaporation temperature on the morphological and physico-chemical properties of the materials was evaluated, together with the effect on actuator functional response. Independently of the IL content and type, and the solvent evaporation temperature, a non-porous structure is obtained. The incorporation of the IL within the polymer matrix does not affect the thermal stability but leads to a decrease in the Young modulus for the different IL/carrageenan samples. The highest influence was observed by using the [Ch][DHP] IL at a filler content of 40% w/w with a decrease in the Young modulus from 748 MPa for the neat polymer to 145 MPa for the [Ch][DHP]/carrageenan sample. Furthermore, the ionic conductivity of the samples increases with increasing IL content, with the highest values being 2.9 × 10-6 S cm-1 and 1.2 × 10-6 S cm-1 for the samples with 40% w/w of [Bmim][FeCl4] and [Ch][DHP], respectively. Regarding the soft actuator performance, the maximum displacement was obtained for the [Ch][DHP]/carrageenan sample with an IL content of 40% w/w, showing a maximum displacement of 5.8 mm at a DC applied voltage of 9 V.publishersversionpublishe

Surface hydrophobization of bacterial and vegetable cellulose fibers using ionic liquids as solvent media and catalysts

The surface hydrophobization through heterogeneous chemical modification of bacterial (and vegetable) cellulose fibers with several anhydrides (acetic, butyric, hexanoic and alkenyl succinic anhydrides) and hexanoyl chloride suspended in an ionic liquid, tetradecyltrihexylphosphonium bis(trifluoromethylsulfonyl) imide, [TDTHP][NTf(2)], was studied. Furthermore, in the reaction with hexanoyl chloride, another ionic liquid, N-hexyl-4-(dimethylamino)pyridinium bis(trifluoromethylsulfonyl) imide, [C(6)N(CH(3))(2)py][NTf(2)], was used instead of common organic bases as catalyst and to trap the released HCl. The analysis of the ensuing modified fibers by FTIR, XRD and SEM clearly showed that the esterification reactions occurred essentially at the fibers' outmost layers, not affecting their ultrastructure. The degree of substitution (DS) of the ensuing esterified fibers ranged from less than 0.002 to 0.41; and in all instances, the fibers' surface acquired a high hydrophobicity. This novel approach constitutes an important strategy in the preparation of modified fibers under greener conditions relaying in the use of non-volatile solvents.FCT - SFRH/BD/72830/2010SFRH/BPD/41781/2007PTDC/QUI/68472/2006PTDC/QUI/72903/200

Exposure effects of endotoxin-free titanium-based wear particles to human osteoblasts

Titanium-based materials are widely employed by the biomedical industry in orthopedic and dental implants. However, when placed into the human body, these materials are highly susceptible to degradation processes, such as corrosion, wear, and tribocorrosion. As a consequence, metallic ions or particles (debris) may be released, and although several studies have been conducted in recent years to better understand the effects of their exposure to living cells, a consensual opinion has not yet been obtained. In this work, we produced metallic based wear particles by tribological tests carried out on Ti-6Al-4V and Ti-15Zr-15Mo alloys. They were posteriorly physicochemically characterized according to their crystal structure, size, morphology, and chemical composition and compared to Ti-6Al-4V commercially available particles. Finally, adsorbed endotoxins were removed (by applying a specific thermal treatment) and endotoxin-free particles were used in cell experiments to evaluate effects of their exposure to human osteoblasts (MG-63 and HOb), namely cell viability/metabolism, proinflammatory cytokine production (IL-6 and PGE2), and susceptibility to internalization processes. Our results indicate that tribologically-obtained wear particles exhibit fundamental differences in terms of size (smaller) and morphology (irregular shapes and rough surfaces) when compared to the commercial ones. Consequently, both Ti-6Al-4V and Ti-15Zr-15Mo particles were able to induce more pronounced effects on cell viability (decrease) and cytokine production (increase) than did Ti-6Al-4V commercial particles. Furthermore, both types of wear particles penetrated osteoblast membranes and were internalized by the cells. Influences on cytokine production by endotoxins were also demonstrated.This work was supported by Fundacao de Amparo a Pesquisa do Estado de Sao Paulo - FAPESP (2015/50280-5 and 2017/24300-4), Fundacao para a Ciencia e Tecnologia - FCT (UID/EEA/04436/2013), Coordenacao de Aperfeicoamento de Pessoal de Nivel Superior - CAPES (Finance Code 0001), FCT/CAPES Joint Research Project (99999.008666/2014-08), FCT COMPETE 2020 (POCI-01-0145-FEDER-006941 and POCI-01-0145-FEDER-007265) and M-ERA-NET (0001/2015)

Transparent bionanocomposites with improved properties prepared from acetylated bacterial cellulose and poly(lactic acid) through a simple approach

The preparation and characterization of biocomposite materials with improved properties based on poly(lactic acid) (PLA) and bacterial cellulose, and, for comparative purposes, vegetal cellulose fibers, both in their pristine form or after acetylation, is reported. The composite materials were obtained through the simple and green mechanical compounding of a PLA matrix and bacterial cellulose nanofibrils (or vegetable fibers), and were characterized by TGA, DSC, tensile assays, DMA, SEM and water uptake. The bionanocomposites obtained from PLA and acetylated bacterial cellulose were particularly interesting, given the considerable improvement in thermal and mechanical properties, as evidenced by the significant increase in both elastic and Young moduli, and in the tensile strength (increments of about 100, 40 and 25%, respectively) at very low nanofiller loadings (up to 6%). These nanocomposites also showed low hygroscopicity and considerable transparency, features reported here for the first time.FCT - PTDC/QUI/68472/2006FCT - SFRH/BPD/63250/2009FCT - L. C. T/ E. T.FCT-CAPES 2009FCT - National Program for Scientific Re-equipmentRede/1509/RME/2005REEQ/515/CTM/200