Quantification of Linalool in 3D Printed Fast-Dissolving Oral Films by A High-Pressure Liquid Chromatography Method

Introduction: Linalool has shown inhibitory effects against Candida albicans. Microbial resistance is developing towards the current antifungal drugs. Therefore, an oral formulation of linalool oil may be used to effectively treat oral thrush. A wide range of patients can use fast-dissolving oral films (FDFs). Three-dimensional printing (3DP) may be utilised for the manufacture of FDFs. Aims: to formulate linalool in FDFs and quantify it using high-pressure liquid chromatography (HPLC). Methods: A powder formulation containing linalool (5%w/w) was prepared and filaments were produced at 75°C and printed at 185°C. The films were dissolved either in methanol or deionised water, and linalool was quantified in the aqueous solutions. The mobile phase of a previously reported HPLC method was modified to quantify linalool in the aqueous solutions. The HPLC method was validated by measuring linalool in standard methanol and aqueous solutions. Results: Preparing aqueous solutions of filaments and films provided less variability in the analyses. 3D-printed FDFs had an average weight of 78.44 ± 6.84 mg. Applying the HPLC method revealed that the amounts of linalool changed from a theoretical 25 mg (per 0.5 g of filament) to the range of 23.98 ± 1.22 to 33.79 ± 2.43 mg. In contrast, the amounts of linalool were changed in films from theoretical 25 mg (per 0.5 g of film) to 13.82 ± 3.24 mg to 21.04 ± 0.92 mg. These observations indicated the evaporation of linalool considerably during printing at 185 °C. Conclusion: This work found that linalool FDFs should be printed at temperatures lower than 185 °C and dissolved in deionised water for better HPLC analytical consistency

The Inclusion of a Matrix Metalloproteinase-9 Responsive Sequence in Self-assembled Peptide-based Brain-Targeting Nanoparticles Improves the Efficiency of Nanoparticles Crossing the Blood-Brain Barrier at Elevated MMP-9 Levels

This study investigated whether the inclusion of a matrix metalloproteinase-9 (MMP-9) responsive sequence in self-assembled peptide-based brain-targeting nanoparticles (NPs) would enhance the blood-brain barrier (BBB) penetration when MMP-9 levels are elevated both in the brain and blood circulation. Brain-targeting peptides were conjugated at the N-terminus to MMP-9-responsive peptides, and these were conjugated at the N-terminus to lipid moiety (cholesteryl chloroformate or palmitic acid). Two constructs did not have MMP-9-responsive peptides. NPs were characterised for size, charge, critical micelle concentration, toxicity, blood compatibility, neural cell uptake, release profiles, and in vitro BBB permeability simulating normal or elevated MMP-9 levels. The inclusion of MMP-9-sensitive sequences did not improve the release of a model drug in the presence of active MMP-9 from NPs compared to distilled water. 19F NMR studies suggested the burial of MMP-9-sensitive sequences inside the NPs making them inaccessible to MMP-9. Only cholesterol-GGGCKAPETALC (responsive to MMP-9) NPs showed <5% haemolysis, <1 pg/mL release of IL-1β at 500 μg/mL from THP1 cells, with 70.75 ± 5.78% of NPs crossing the BBB at 24 h in presence of active MMP-9. In conclusion, brain-targeting NPs showed higher transport across the BBB model when MMP-9 levels were elevated and the brain-targeting ligand was responsive to MMP-9

Potential of a cyclone prototype spacer to improve in vitro dry powder delivery

Copyright The Author(s) 2013. This article is published with open access at Springerlink.com. This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and the source are creditedPurpose: Low inspiratory force in patients with lung disease is associated with poor deagglomeration and high throat deposition when using dry powder inhalers (DPIs). The potential of two reverse flow cyclone prototypes as spacers for commercial carrierbased DPIs was investigated. Methods: Cyclohaler®, Accuhaler® and Easyhaler® were tested with and without the spacers between 30-60 Lmin-1. Deposition of particles in the next generation impactor and within the devices was determined by high performance liquid chromatography. Results: Reduced induction port deposition of the emitted particles from the cyclones was observed due to the high retention of the drug within the spacers (e.g. salbutamol sulphate (SS): 67.89 ± 6.51 % at 30 Lmin-1 in Cheng 1). Fine particle fractions of aerosol as emitted from the cyclones were substantially higher than the DPIs alone. Moreover, the aerodynamic diameters of particles emitted from the cyclones were halved compared to the DPIs alone (e.g. SS from the Cyclohaler® at 4 kPa: 1.08 ± 0.05 μm vs. 3.00 ± 0.12 μm, with and without Cheng 2, respectively) and unaltered with increased flow rates. Conclusion: This work has shown the potential of employing a cyclone spacer for commercial carrier-based DPIs to improve inhaled drug delivery.Peer reviewe

Formulation and optimisation of novel transfersomes for sustained release of local anaesthetic

Objective: To investigate the effect of formulation parameters on the preparation of transfersomes as sustained‐release delivery systems for lidocaine and to develop and validate a new high‐performance liquid chromatography (HPLC) method for analysis. Method: Taguchi design of experiment (DOE) was used to optimise lidocaine‐loaded transfersomes in terms of phospholipid, edge activator (EA) and phospholipid : EA ratio. Transfersomes were characterised for size, polydispersity index (PDI), charge and entrapment efficiency (%EE). A HPLC method for lidocaine quantification was optimised and validated using a mobile phase of 30%v/v PBS (0.01 m) : 70%v/v Acetonitrile at a flow rate of 1 ml/min, detected at 255 nm with retention time of 2.84 min. The release of lidocaine from selected samples was assessed in vitro. Key findings: Transfersomes were 200 nm in size, with PDI ~ 0.3. HPLC method was valid for linearity (0.1–2 mg/ml, R2 0.9999), accuracy, intermediate precision and repeatability according to ICH guidelines. The %EE was between 44% and 56% and dependent on the formulation parameters. Taguchi DOE showed the effect of factors was in the rank order : lipid : EA ratio ˃ EA type ˃ lipid type. Optimised transfersomes sustained the release of lidocaine over 24 h. Conclusion: Sustained‐release, lidocaine‐loaded transfersomes were successfully formulated and optimised using a DOE approach, and a new HPLC method for lidocaine analysis was developed and validated

Development of microspheres for biomedical applications: a review

An overview of microspheres manufactured for use in biomedical applications based on recent literature is presented in this review. Different types of glasses (i.e. silicate, borate, and phosphates), ceramics and polymer-based microspheres (both natural and synthetic) in the form of porous , non-porous and hollow structures that are either already in use or are currently being investigated within the biomedical area are discussed. The advantages of using microspheres in applications such as drug delivery, bone tissue engineering and regeneration, absorption and desorption of substances, kinetic release of the loaded drug components are also presented. This review also reports on the preparation and characterisation methodologies used for the manufacture of these microspheres. Finally, a brief summary of the existing challenges associated with processing these microspheres which requires further research and development are presented

riDOM, a Cell-Penetrating Peptide : Interaction with DNA and Heparan Sulfate

DNA condensation in the presence of polycationic molecules is a well-known phenomenon exploited in gene delivery. riDOM (retro-inverso dioleoylmelittin) is a cell-penetrating peptide with excellent transporter properties for DNA. It is a chimeric molecule where ri-melittin is fused to dioleoylphosphoethanolamine. The physical-chemical properties of riDOM in solution and in the presence of DNA and heparan sulfate were investigated with spectroscopic and thermodynamic methods. Dynamic light scattering shows that riDOM in solution aggregates to well-defined nanoparticles with a diameter of ∼13 nm and a ζ-potential of 22 mV, composed of about 220-270 molecules. Binding of riDOM to DNA was studied with dynamic light scattering, ζ-potential measurements, and isothermal titration calorimetry and was compared with authentic melittin-DNA interaction. riDOM binds tightly to DNA with a microscopic binding constant of 5 × 10(7) M(-1) and a stoichiometry of 12 riDOM per 10 DNA base pairs. In the complex the DNA double strand is completely shielded by the more hydrophobic riDOM molecules. Authentic melittin binds to DNA with a much lower binding constant of 5 × 10(6) M(-1) and lower stoichiometry of 5 melittin per 10 DNA base pairs. The binding enthalpies for riDOM and melittin are small and the binding reactions are entropy-driven. Sulfated glycosaminoglycans such as heparan sulfate are also linear molecules with a negative charge. riDOM binding to heparan sulfate on cell surfaces can therefore interfere with DNA-riDOM binding. riDOM-heparan sulfate complex formation was characterized by isothermal titration calorimetry and spectroscopic methods. The binding constant of riDOM for heparan sulfate is K ≈ 2 × 10(6) M(-1). Authentic melittin has a similar binding constant but riDOM shows a 3-fold higher packing density on heparan sulfate than the distinctly smaller melittin