Comparison of matching layers for automotive radome design

Hidden integration of 79 GHz sensors behind plastic and painted fascia represents a challenging task since both electromagnetic and car body design constraints have to be met. This paper compares different possibilities for low-cost integration of radar sensors. Based on a model for stratified media, a study of the most important parameters such as bandwidth, angle and tolerances is shown. Our results suggest that for plastic fascia, the requirements of future radar sensors can be met with low-cost matching. Even with metallic paints, the requirements imposed by modern 79 GHz radar sensors can be met under certain conditions

A varactor tuned low-cost 24 GHz harmonic VCO

We present a low-cost 24 GHz VCO that is based on a microstrip design combined with discrete packaged devices. The output frequency is generated by a harmonic oscillator. The tunabilty was reached using a varactor diode. Two versions of the VCO were built, one has a wide tuning range of 1.1 GHz and the other one has a high output power of 3.7 dBm

First harmonic injection locking of 24-GHz-oscillators

An increasing number of applications is proposed for the 24 GHz ISM-band, like automotive radar systems and short-range communication links. These applications demand for oscillators providing moderate output power of a few mW and moderate frequency stability of about 0.5%. The maximum oscillation frequency of low-cost off-theshelf transistors is too low for stable operation of a fundamental 24GHz oscillator. Thus, we designed a 24 GHz first harmonic oscillator, where the power generated at the fundamental frequency (12 GHz) is reflected resulting in effective generation of output power at the first harmonic. We measured a radiated power from an integrated planar antenna of more than 1mW. Though this oscillator provides superior frequency stability compared to fundamental oscillators, for some applications additional stabilization is required. As a low-cost measure, injection locking can be used to phase lock oscillators that provide sufficient stability in free running mode. Due to our harmonic oscillator concept injection locking has to be achieved at the first harmonic, since only the antenna is accessible for signal injection. We designed, fabricated and characterized a harmonic oscillator using the antenna as a port for injection locking. The locking range was measured versus various parameters. In addition, phase-noise improvement was investigated. A theoretical approach for the mechanism of first harmonic injection locking is presented

Design and realization of a broadband single-side-band mixer with a very short settling time

To achieve high range resolution in synthetic aperture radar imaging a frequency synthesizer with high bandwidth is a possible solution. To operate in the required frequency band an LF-signal usually has to be upconverted. In this paper we describe the design and realization of a broadband Single-Side-Band Mixer with a very short settling time between frequency steps of arbitrary length inside a high bandwidth. Compared to already existing SSB-Mixers, our novel concept has three major advantages: At first, the mixer could be used in combination with an arbitrary signal source. Due to a modular circuit concept it is possible to use the system for different input frequency ranges. Moreover, just by changing single modules, the output frequency-range can be adapted to individual requirements. Thirdly, as a main advantage, the system is able to generate a high frequency output span with a very fast settling time between frequency steps. Even with applied steps up to 400 MHz, the settling time remains below 3 μs, which is more than 5 times faster than the settling time of similar synthesizers

MmWave scattering properties of roads on rough asphalt and concrete surfaces

In this work, a synthetic aperture radar setup is used for analyzing the mmWave scattering of road surfaces in the automotive 77 GHz band in the laboratory. With this setup, samples of concrete roads in two different surface conditions are investigated, determining the variances in reflectivity depending on material composition and surface structure. Afterward, the distribution of these variations is fitted using probability density functions, namely normal and rayleigh distribution fits. Consequently, the diffuse scattering behavior of concrete roads can be described mathematically. Additionally, previously presented porous asphalt roads are compared and fitted analogously to get a summary of the scattering for all common road surfaces in Germany. Furthermore, a validation of the measurement and the processing by analyzing particularly generated reference samples is performed.</p

Ralstonia pickettii—innocent bystander or a potential threat?

ABSTRACTRalstonia pickettii can be isolated from water, soil and plants, and can also form part of the commensal flora of the oral cavity and the upper respiratory tract of healthy individuals. R. pickettii is an infrequent pathogen, but can cause infections, mainly of the respiratory tract, in immunocompromised and cystic fibrosis patients. It can be isolated from a variety of clinical specimens, including sputum, blood, wound infections, urine, ear and nose swabs, and cerebrospinal fluid. Resistance can occur to ciprofloxacin, trimethoprim–sulphamethoxazole, piperacillin–tazobactam, imipenem–cilastatin and ceftazidime. Early detection of R. pickettii allows prompt appropriate antimicrobial therapy with a favourable outcome, but removal of infected indwelling devices is mandatory

A software-radio front-end for microwave applications

In modern communication, sensor and signal processing systems digitisation methods are gaining importance. They allow for building software configurable systems and provide better stability and reproducibility. Moreover digital front-ends cover a wider range of applications and have better performance compared with analog ones. The quest for new architectures in radio frequency front-ends is a clear consequence of the ever increasing number of different standards and the resulting task to provide a platform which covers as many standards as possible. At microwave frequencies, in particular at frequencies beyond 10 GHz, no direct sampling receivers are available yet. A look at the roadmap of the development of commercial analog-to-digital-converters (ADC) shows clearly, that they can neither be expected in near future. We present a novel architecture, which is capable of direct sampling of band-limited signals at frequencies beyond 10 GHz by means of an over-sampling technique. The wellknown Nyquist criterion states that wide-band digitisation of an RF-signal with a maximum frequency ƒ requires a minimum sampling rate of 2 · ƒ . But for a band-limited signal of bandwidth B the demands for the minimum sampling rate of the ADC relax to the value 2 · B. Employing a noise-forming sigma-delta ADC architecture even with a 1-bit-ADC a signal-to-noise ratio sufficient for many applications can be achieved. The key component of this architecture is the sample-and-hold switch. The required bandwidth of this switch must be well above 2 · ƒ . We designed, fabricated and characterized a preliminary demonstrator for the ISM-band at 2.4 GHz employing silicon Schottky diodes as a switch and SiGe-based MMICs as impedance transformers and comparators. Simulated and measured results will be presented

A planar hybrid transceiving mixer at 76.5GHz for automotive radar applications

A growing number of applications for radar systems in automobiles demands for low-cost radar front-ends. A planar monostatic radar front-end is particularly suited for low cost applications as it uses only one antenna for transmission and reception and, thus, minimizes the needed chip area. Generally, in a standard homodyne radar a radio-frequency (RF) signal generated by an oscillator is used for both, the transmitted signal and the local oscillator (LO). Well controlled distribution of the input power between antenna and mixer is crucial. A transceiving mixer at 76.5GHz is presented, where this distribution is done by use of a rat-race coupler. In a conventional transceiver the oscillator signal is split into the transmitted and in the LO signal by a directional coupler. A second directional coupler is needed in order to merge the received and the LO signal at the mixer. In our design the purpose of splitting and merging the signals is realized with only one coupler. Elimination of the second coupler reduces losses significantly. The received signal is down-converted to the intermediate frequency (IF) by use of a balanced mixer. For small relative speed in a CW-Doppler-radar or short distance in a FMCWradar the IF is very small. Therefore 1/f noise is a significant value. In order to achieve good 1/f noise characteristics, Schottky diodes were used. The diodes were flip-chip bonded onto a microstrip circuit on a Al2O3 substrate. The assembled transceiver was measured on-waver. An input power of 7 dBm was applied. The measured output power was 3 dBm and the conversion loss 9 dB. A noise figure of 15.3 dB was measured at 100 kHz

Drosophila TNF modulates tissue tension in the embryo to facilitate macrophage invasive migration

Migrating cells penetrate tissue barriers during development, inflammatory responses, and tumor metastasis. We study if migration in vivo in such three-dimensionally confined environments requires changes in the mechanical properties of the surrounding cells using embryonic Drosophila melanogaster hemocytes, also called macrophages, as a model. We find that macrophage invasion into the germband through transient separation of the apposing ectoderm and mesoderm requires cell deformations and reductions in apical tension in the ectoderm. Interestingly, the genetic pathway governing these mechanical shifts acts downstream of the only known tumor necrosis factor superfamily member in Drosophila, Eiger, and its receptor, Grindelwald. Eiger-Grindelwald signaling reduces levels of active Myosin in the germband ectodermal cortex through the localization of a Crumbs complex component, Patj (Pals-1-associated tight junction protein). We therefore elucidate a distinct molecular pathway that controls tissue tension and demonstrate the importance of such regulation for invasive migration in vivo

Control of primary productivity and the significance of photosynthetic bacteria in a meromictic kettle lake.

During 1986 planktonic primary production and controlling factors were investigated in a small (A0 = 11.8 · 103 m2, Zmax = 11.5 m) meromictic kettle lake (Mittlerer Buchensee). Annual phytoplankton productivity was estimated to ca 120 gC · m–2 · a–1 (1,42 tC · lake–1 · a–1). The marked thermal stratification of the lake led to irregular vertical distributions of chlorophylla concentrations (Chla) and, to a minor extent, of photosynthesis (Az). Between the depths of 0 to 6 m low Chla concentrations (< 7 mg · m–3) and comparatively high background light attenuation (kw = 0,525 m–1, 77% of total attenuation due to gelbstoff and abioseston) was found. As a consequence, light absorption by algae was low (mean value 17,4%) and self-shading was absent. Because of the small seasonal variation of Chla concentrations, no significant correlation between Chla and areal photosynthesis (A) was observed. Only in early summer (June–July) biomass appears to influence the vertical distribution of photosynthesis on a bigger scale. Around 8 m depth, low-light adapted algae and phototrophic bacteria formed dense layers. Due to low ambient irradiances, the contribution of these organisms to total primary productivity was small. Primary production and incident irradiance were significantly correlated with each other (r2 = 0.68). Although the maximum assimilation number (Popt) showed a clear dependence upon water temperature (Q10 = 2.31), the latter was of minor importance to areal photosynthesis