Leak Rate Quantification Method for Gas Pressure Seals with Controlled Pressure Differential

An enhancement to the pressure decay leak rate method with mass point analysis solved deficiencies in the standard method. By adding a control system, a constant gas pressure differential across the test article was maintained. As a result, the desired pressure condition was met at the onset of the test, and the mass leak rate and measurement uncertainty were computed in real-time. The data acquisition and control system were programmed to automatically stop when specified criteria were met. Typically, the test was stopped when a specified level of measurement uncertainty was attained. Using silicone O-ring test articles, the new method was compared with the standard method that permitted the downstream pressure to be non-constant atmospheric pressure. The two methods recorded comparable leak rates, but the new method recorded leak rates with significantly lower measurement uncertainty, statistical variance, and test duration. Utilizing this new method in leak rate quantification, projects will reduce cost and schedule, improve test results, and ease interpretation between data sets

NEW DISCOVERIES from the ARECIBO 327 MHz DRIFT PULSAR SURVEY RADIO TRANSIENT SEARCH

We present Clusterrank, a new algorithm for identifying dispersed astrophysical pulses. Such pulses are commonly detected from Galactic pulsars and rotating radio transients (RRATs), which are neutron stars with sporadic radio emission. More recently, isolated, highly dispersed pulses dubbed fast radio bursts (FRBs) have been identified as the potential signature of an extragalactic cataclysmic radio source distinct from pulsars and RRATs. Clusterrank helped us discover 14 pulsars and 8 RRATs in data from the Arecibo 327 MHz Drift Pulsar Survey (AO327). The new RRATs have DMs in the range 23.5-86.6 pc cm-3 and periods in the range 0.172-3.901 s. The new pulsars have DMs in the range 23.6-133.3 pc cm-3 and periods in the range 1.249-5.012 s, and include two nullers and a mode-switching object. We estimate an upper limit on the all-sky FRB rate of 105 day-1 for bursts with a width of 10 ms and flux density ≳83 mJy. The DMs of all new discoveries are consistent with a Galactic origin. In comparing statistics of the new RRATs with sources from the RRATalog, we find that both sets are drawn from the same period distribution. In contrast, we find that the period distribution of the new pulsars is different from the period distributions of canonical pulsars in the ATNF catalog or pulsars found in AO327 data by a periodicity search. This indicates that Clusterrank is a powerful complement to periodicity searches and uncovers a subset of the pulsar population that has so far been underrepresented in survey results and therefore in Galactic pulsar population models

Scoping study examining the behaviour of Boom Clay at disposal depths investigated in OPERA

The Onderzoeks Programma Eindberging Radioactief Afval (OPERA) is the third national research programme for the geological disposal of radioactive waste in the Netherlands, operating during the period 2011 to 2017. The rock types to host a geological disposal facility that are currently being considered in the Netherlands are salt and clay. Earlier Dutch work focussed mostly on salt, but the present programme OPERA is focused on a specific clay formation the Boom Clay. Previous studies have primarily focused on examining behaviour at the Belgium reference depth (~220m). The work presented in this study extends this knowledge-base to repository depths of potential interest in the Netherlands (~500m). In this report, results from a scoping study examining the hydromechanical properties of Boom Clay are presented, including investigations on consolidation, swelling, hydraulic, gas and deformation behaviour. These were performed on preserved core material retrieved from the HADES underground research laboratory, Belgium. Sections of core were then consolidated to a depth representative of the Netherlands. Permeability was sensitive to stress state and thermal load, though incremental changes in NaCl concentration had minimal impact. Hysteresis was observed in thermally induced changes in permeability. Gas entry was closely linked to the minimum principal stress component, with mass and volume changes of samples observed as a result of gas migration. Stress, porewater pressure and gas flow were integrally linked with pathways evolving temporally and spatially. A transition from brittle to ductile deformation was noted with increasing stress in both compression and shear. Boom Clay is both complex and anisotropic in its behaviour

Improving the sensitivity of immunoassays with PEG-COOH-like film prepared by plasma-based technique

Herein we report on a preparation and performance of stable, hydrophilic and biocompatible polymeric material suitable for functionalization of disposable substrates used in biosensors. This new material features -COOH surface groups cross-linked with ethylene glycol molecules and was prepared in situ on disposable, plastic substrate by high-throughput and environmentally friendly technique called plasma-enhanced chemical vapor deposition (PECVD). The film is grafted to the plasma activated plastic by sequential deposition of tetraethylorthosilicate, forming a bonding layer, and mixed vapors of acrylic acid and diethyleneglycol dimethylether (AA/PEG) that provide the desired functional groups forming a sensing, contact layer. A superior performance of the AA/PEG coating as suitable material for substrates in biomedical devices was demonstrated in a model fluorescence linked immunosorbent assay. The results were compared with other commonly used surface materials prepared by wet chemistry methods. The unique characteristic of the AA/PEG film is that the immunoassay can be executed without the need for a blocking step, typically using albumins, without negative consequences on the bioassay results. In fact, the superior quality of the materials modified with AA/PEG film was highlighted by improving the sensitivity of an immunoassay by two orders of magnitude when compared with substrates prepared by standard surface chemistry methods. Copyright © 2011 Wiley Periodicals, Inc

An Overview of Advanced Elastomeric Seal Development and Testing Capabilities at NASA Glenn Research Center

NASA is developing advanced space-rated elastomeric seals to support future space exploration missions to low Earth orbit, the Moon, near Earth asteroids, and other destinations. This includes seals for a new docking system and vehicle hatches. These seals must exhibit extremely low leak rates to ensure that astronauts have sufficient breathable air for extended missions. Seal compression loads must be below prescribed limits so as not to overload the mechanisms that compress them, and seal adhesion forces must be low to allow the sealed interface to be separated when required (e.g., during undocking or hatch opening). NASA Glenn Research Center has developed a number of unique test fixtures to measure the leak rates and compression and adhesion loads of candidate seal designs under simulated thermal, vacuum, and engagement conditions. Tests can be performed on full-scale seals with diameters on the order of 50 in., subscale seals that are about 12 in. in diameter, and smaller specimens such as O-rings. Test conditions include temperatures ranging from -238 to +662F (-150 to +350C), operational pressure gradients, and seal-on-seal or seal-on-flange mating configurations. Nominal and off-nominal conditions (e.g., incomplete seal compression) can also be simulated. This paper describes the main design features and capabilities of each test apparatus and provides an overview of advanced seal development activities at NASA Glenn

PECVD coatings for functionalization of point-of-care biosensor surfaces

In early stage disease diagnosis, an accurate and reliable measurement of low concentrations of specific biomarkers is a key need. The detection technique requires the reaction of an antibody, which is generally covalently bound to the biosensor platform, with its antigen. The application of Zeonor ®, a cyclo olefin copolymer (COP) with very low autofluorescence, good optical properties and high precision molding characteristics, as a biosensor platform has been demonstrated recently. Highly reproducible, industrial scale surface chemical modification of the COP plastic for covalent attachment of the biomolecules for specific recognition of the target, together with low non-specific binding of other proteins that may be present in the sample is a key challenge. In this work, the applicability of plasma enhanced chemical vapor deposition (PECVD) process has been demonstrated by depositing varying surface functionalities including amines, carboxylic, mercapto, epoxy and polyethylene glycol functionalities. The plasma functionalized coatings thus created possess both reactive and repellent sites on the biosensor chip, allowing the chip to be configured either for fluorescence or light scattering-based detection or for label-free surface plasmon resonance detection techniques. The versatility of the gas phase deposition process for building sequential chemistries on low cost and disposable plastic chips is presented in detail. © 2011 Elsevier Ltd. All rights reserved

CONTAIN D11 : integrated final results and conclusions

Carbon capture and storage is a technology capable of reducing CO2 outputs on a large scale; the concept usually requires CO2 to be removed from post-combustion flue gases and sequestered in geological formations. Depleted gas fields constitute “the most important storage type for the UK” and will provide a large and important potential future offshore storage capacity (DECC, 2012). Over the last 4 years, the CONTAIN research project has focussed on the geomechanical behaviour of depleted hydrocarbon fields in response to injection with CO2, combining a modelling and experimental approach with the public perceptions of CCS into three work packages. The project has provided a better understanding of the hydromechanical impacts of depletion on caprocks and the effect of subsequent CO2 injection, in order to assist with the implementation of CCS in this type of reservoir. Work package 1 outlined a phenomenological approach to assessing possible deformation during operation. Focus was placed on rock mechanics and transport experiments on material from the geologies of target formations in the North Sea, providing information that could be incorporated into numerical simulations. Work package 2 expanded this understanding by considering fractured caprock. Numerical modelling was used to study the deformation of an initially intact caprock caused by the depletion of an underlying reservoir during oil extraction. Deformation and flow were geomechanically modelled in three dimensions using a fully coupled poroelastic model, incorporating discrete fractures and faults into the caprock. Work package 3 offered new and valuable insight on future public awareness campaigns aimed at gaining acceptance of CCS. Qualitative expert interviews have been used, a CCS expert survey and a public survey across four countries to gain an understanding of perceptions of CCS risks and benefits, and has allowed for comparison of views on CCS between experts and public. In addition, the work package has explored the impact of different message framings on CCS attitudes. The findings of each work package are summarised in this report, with each work package represented by a report chapter. A synthesis of the findings and discussion of the work as a whole follows

Excavation of an early 17th-century glassmaking site at Glasshouse, Shinrone, Co. Offaly, Ireland

An archaeological research excavation was conducted in the area immediately surrounding an upstanding glassmaking furnace near Shinrone, Co. Offaly, Ireland. It dates to the early to mid 17th century and was built and operated by French Huguenots, probably de Hennezells (de Hennezel/Henzeys/Hensie) who had settled in this region as part of the Crown plantation of King’s County (now Co. Offaly). This furnace, which employed wood rather than coal as a fuel, is a very rare survival, with no other upstanding examples known in Ireland, Britain or the Lorraine region of France where the form probably originated