Structural Dependence of the Molecular Mobility in the Amorphous Fractions of Polylactide

Fragility index and cooperativity length characterizing the molecular mobility in the amorphous phase are for the first time calculated in drawn polylactide (PLA). The microstructure of the samples is investigated from wide-angle X-ray scattering (WAXS) whereas the amorphous phase dynamics are revealed from broadband dielectric spectroscopy (BDS) and temperature-modulated differential scanning calorimetry (TMDSC). The drawing processes induce the decrease of both cooperativity and fragility with the orientation of the macromolecules. Post-drawing annealing reveals an unusual absence of correlation between the evolutions of cooperativity length and fragility. The cooperativity length remains the same compared to the drawn sample while a huge increase of the fragility index is recorded. By splitting the fragility index in a volume contribution and an energetic contribution, it is revealed that the amorphous phase in annealed samples exhibits a high energetic parameter, even exceeding the amorphous matrix value. It is assumed that the relaxation process is driven in such a way that the volume hindrance caused by the thermomechanical constraint is compensated by the acceleration of segmental motions linked to the increase of degrees of freedom. This result should also contribute to the understanding of the constraint slackening in the amorphous phase during annealing of drawn PLA, which causes among others the decrease of its barrier properties

Exploiting Light Interferences to Generate Micrometer-High Superstructures from Monomeric Azo Materials with Extensive Orientational Mobility

Photochromic azo materials have stirred considerable interest for their ability to mechanically respond to polarized light through large photo-induced migration and orientation processes. In order to apprehend the microscopic dynamics behind the extensive mass transport occurring under interferential illumination, two azo compounds differing by their propen-sity to form hydrogen bonds are synthesized and processed as nondoped glassy thin films. Interferential irradiation using polarization and intensity patterns reveals fully distinct responses. Regular nanometer-high surface relief gratings transform into micrometer superstructures with an ampli-tude ten times higher than the initial film thickness when using the latter polarization. Systematic comparisons between the azo materials in terms of thermal properties, photochromism in solution and in the solid state, and photomigration are carried out. The progressive formation of super-structures is ascribed to two successive processes. The first one relates to fast photoinduced migration due to the impinging structured light, and the second one is promoted by slower thermally activated “zig-zag”-like diffu-sion and Z-E thermal relaxation, which in turn requests high orientational mobility of the azo compounds and causes large nanomechanical changes. Such studies should provide novel structural guidelines in terms of material fluidity to rapidly achieve highly structured and rewritable materials at lilogwht irradiance

Impact of Nanoconfinement on Polylactide Crystallization and Gas Barrier Properties

The barrier properties of poly(l-lactide) (PLLA) were investigated in multinanolayer systems, probing the effect of confinement, the compatibility between the confining and the confined polymer, crystal orientation, and amorphous phase properties. The multilayer coextrusion process was used to confine PLLA between two amorphous polymers (polystyrene, PS; and polycarbonate, PC), which have different chemical affinities with PLLA. Confined PLLA layers of approximately 20 nm thickness were obtained. The multinanolayer materials were annealed at different temperatures to obtain PLLA crystallites with distinct polymorphs. PLLA annealed in PC/PLLA films at 120 °C afforded a crystallinity degree up to 65%, and PLLA annealed in PC/PLLA or PS/PLLA films at 85 °C had a crystallinity degree of 45%. WAXS measurements evidenced that the PLLA lamellas between PS layers had a mixed in-plane and on-edge orientation. PLLA lamellas between PC layers were uniquely oriented in-plane. DMA results evidenced a shift of the PC glass transition toward lower temperature, suggesting the possible presence of an interphase. The development of the rigid amorphous fraction (RAF) in the amorphous phase during annealing was impacted by the confiner polymer. The RAF content of semicrystalline PLLA was about 15% in PC/PLLA, whereas it was neglectable in PS/PLLA. The oxygen barrier properties appeared to be governed by RAF content, and no impact of the PLLA polymorph or the crystalline orientation was observed. This study shows that the confinement of PLLA on itself does not impact barrier properties but that the proper choice of the confiner polymer can lead to decrease the phase coupling which creates the RAF. It is the prevention of RAF that decreases permeability

Reduced physical aging rates of polylactide in polystyrene/polylactide multilayer films from fast scanning calorimetry

The physical aging behavior of amorphous polylactide constrained against polystyrene in layers of 300 nm, thanks to the layer–multiplying co–extrusion process, was investigated by fast–scanning calorimetry (FSC). By cooling down the sample from the liquid state to the glassy one at very fast scanning rates, it was possible to investigate the structural relaxation of the polymer glass at high temperatures for which the time needed to reach the equilibrium was shortened. Therefore it was possible to perform the study of physical aging in experimental conditions providing an expanded view of the structural relaxation for short aging times. Taking benefit of this property, it was highlighted that the aging kinetics of polylactide occurred significantly slower in the multilayer film, in comparison with a bulk amorphous film. The process of recovery in the multilayer system was found to occur at similar rates, or even slower, than in a three–layer film in which polylactide reached its maximum extent of crystallinity. This was attributed to mobility hindrance that might be inherent to the extrusion conditions or associated with the presence of capped interfaces with polystyrene

Structure and Barrier Properties of Multinanolayered Biodegradable PLA/PBSA Films: Confinement Effect via Forced Assembly Coextrusion

Multilayer coextrusion processing was applied to produce 2049-layer film of poly(butylene succinate-co-butylene adipate) (PBSA) confined against poly(lactic acid) (PLA) using forced assembly, where the PBSA layer thickness was about 60 nm. This unique technology allowed to process semicrystalline PBSA as confined polymer and amorphous PLA as confining polymer in a continuous manner. The continuity of PBSA layers within the 80/20 wt % PLA/PBSA layered films was clearly evidenced by atomic force microscopy (AFM). Similar thermal events to the reference films were revealed by thermal studies; indicating no diffusion of polymers during the melt-processing. Mechanical properties were measured for the multilayer film and the obtained results were those expected considering the fraction of each polymer, revealing the absence of delamination in the PLA/PBSA multinanolayer film. The confinement effect induced by PLA led to a slight orientation of the crystals, an increase of the rigid amorphous fraction (RAF) in PBSA with a densification of this fraction without changing film crystallinity. These structural changes allowed to strongly improve the water vapor and gas barrier properties of the PBSA layer into the multilayer film up to two decades in the case of CO2 gas. By confining the PBSA structure in very thin and continuous layers, it was then possible to improve the barrier performances of a biodegradable system and the resulting barrier properties were successfully correlated to the effect of confinement on the microstructure and the chain segment mobility of the amorphous phase. Such investigation on these multinanolayers of PLA/PBSA with the aim of evidencing relationships between microstructure implying RAF and barrier performances has never been performed yet. Besides, gas and water permeation results have shown that the barrier improvement obtained from the multilayer was mainly due to the reduction of solubility linked to the reduction of the free volume while the tortuosity effect, as usually expected, was not really observed. This work brings new insights in the field of physicochemical behaviors of new multilayer films made of biodegradable polyesters but also in interfacial processes due to the confinement effect induced in these multinanolayer structures obtained by the forced assembly coextrusion. This original coextrusion process was a very advantageous technique to produce eco-friendly materials with functional properties without the help of tie layer, additives, solvents, surface treatments, or inorganic fillers

Effect of Mechanical Horse Practice as New Postural Training in Patients With Neurological Disorders: A Pilot Study

Objective: From a dynamic system approach, this study evaluated the impact of a new training protocol using a mechanical horse on the postural coordination of brain-damaged patients.Methods: Eighteen volunteer brain-damaged patients (i.e., post-stroke or traumatic brain injury) were recruited and randomly divided into an experimental group (horse group; n = 10, conventional therapy associated with horse-riding exercise on the mechanical horse for 30 min, twice a week, for 12 weeks) and a control group (n = 8; conventional therapy without intervention on the mechanical horse). Postural coordination was evaluated during pre- and post-tests through discrete relative phase (DRP) computation: ϕHead−Horse, ϕTrunk−Horse.Results: A significant effect of used training has been showed, F(1, 15) = 16.6 (p < 0.05) for all patients, concerning the trunk/horse coordination.Conclusion: This pilot study results showed the impact of this new training method on the postural coordination of these patients. After 24 sessions, the coordination of the horse group patients differed from that of the control group, showing their ability to adapt to constraints and develop specific modes of postural coordination (trunk/horse antiphase) to optimize their posture

Impact of water and thermal induced crystallizations in a PC/MXD6 multilayer film on barrier properties

A multilayer film composed of alternating layers of polycarbonate (PC) and poly(m-xylene adipamide) (MXD6) was elaborated by using an innovative multilayer coextrusion process. Quasi-continuous thin MXD6 layers (nanolayers) alternating with PC layers were successfully obtained. The PC/MXD6 multilayer film showed a confining effect of MXD6 exerted by PC layers leading to an improvement of barrier properties despite a low degree of crystallinity (X c < 10 wt%). In order to further improve the barrier performances, crystallization treatments induced by water and by heating were then applied on the multilayer film and allowed reaching around 30 wt% of crystallinity in MXD6 layers. To decouple crystallization and geometrical constraint effects on the barrier properties in the multilayer films, the two treatments were also applied on MXD6 films. Surprisingly, despite an increase of the degree of crystallinity from 6 to 26%, water crystallization did not permit to improve gas barrier performances of the MXD6 film nor into the PC/MXD6 multilayer film. On the other hand, thermal crystallization of MXD6 in the multilayer film seems to be a more efficient route to strongly decrease the gas and moisture permeability, up to 75% for nitrogen, 58% for oxygen, 84% for carbon dioxide and 43% for water

Amorphous rigidification and cooperativity drop in semi−crystalline plasticized polylactide

Plasticization of amorphous polylactide shifts the glass transition and extends its temperature range of crystallization to lower temperatures. In this work, we focus on how low−temperature crystallization impacts the mobility of the amorphous phase. Plasticizer accumulates in the amorphous phase because it is excluded from the growing crystal. The formation of rigid amorphous fraction is favored by the low crystallization temperature. It reaches values up to 50% in plasticized polylactide. The increase in the content of rigid amorphous fraction coincides with both the increase of free volume quantified by positron annihilation lifetime spectroscopy, and the decrease in the cooperativity length obtained from the temperature fluctuation approach. The drop of cooperativity is interpreted in terms of mobility gradient due to the amorphous rigidification

Water-Induced Breaking of Interfacial Cohesiveness in a Poly(lactic acid)/Miscanthus Fibers Biocomposite

The impact of the immersion in water on the morphology and the thermomechanical properties of a biocomposite made of a matrix of poly (lactic acid) (PLA) modified with an ethylene acrylate toughening agent, and reinforced with miscanthus fibers, has been investigated. Whereas no evidence of hydrolytic degradation has been found, the mechanical properties of the biocomposite have been weakened by the immersion. Scanning electron microscopy (SEM) pictures reveal that the water-induced degradation is mainly driven by the cracking of the fiber/matrix interface, suggesting that the cohesiveness is a preponderant factor to consider for the control of the biocomposite decomposition in aqueous environments. Interestingly, it is observed that the loss of mechanical properties is aggravated when the stereoregularity of PLA is the highest, and when increasing the degree of crystallinity. To investigate the influence of the annealing on the matrix behavior, crystallization at various temperatures has been performed on tensile bars of PLA made by additive manufacturing with an incomplete filling to enhance the contact area between water and polymer. While a clear fragilization occurs in the material crystallized at high temperature, PLA crystallized at low temperature better maintains its properties and even shows high elongation at break likely due to the low size of the spherulites in these annealing conditions. These results show that the tailoring of the mesoscale organization in biopolymers and biocomposites can help control their property evolution and possibly their degradation in water

Distinct dynamics of structural relaxation in the amorphous phase of poly( l -lactic acid) revealed by quiescent crystallization

International audienc