4,033 research outputs found
Innovative observing strategy and orbit determination for Low Earth Orbit Space Debris
We present the results of a large scale simulation, reproducing the behavior
of a data center for the build-up and maintenance of a complete catalog of
space debris in the upper part of the low Earth orbits region (LEO). The
purpose is to determine the performances of a network of advanced optical
sensors, through the use of the newest orbit determination algorithms developed
by the Department of Mathematics of Pisa (DM). Such a network has been proposed
to ESA in the Space Situational Awareness (SSA) framework by Carlo Gavazzi
Space SpA (CGS), Istituto Nazionale di Astrofisica (INAF), DM, and Istituto di
Scienza e Tecnologie dell'Informazione (ISTI-CNR). The conclusion is that it is
possible to use a network of optical sensors to build up a catalog containing
more than 98% of the objects with perigee height between 1100 and 2000 km,
which would be observable by a reference radar system selected as comparison.
It is also possible to maintain such a catalog within the accuracy requirements
motivated by collision avoidance, and to detect catastrophic fragmentation
events. However, such results depend upon specific assumptions on the sensor
and on the software technologies
Orbit determination of space objects based on sparse optical data
While building up a catalog of Earth orbiting objects, if the available
optical observations are sparse, not deliberate follow ups of specific objects,
no orbit determination is possible without previous correlation of observations
obtained at different times. This correlation step is the most computationally
intensive, and becomes more and more difficult as the number of objects to be
discovered increases. In this paper we tested two different algorithms (and the
related prototype software) recently developed to solve the correlation problem
for objects in geostationary orbit (GEO), including the accurate orbit
determination by full least squares solutions with all six orbital elements.
Because of the presence in the GEO region of a significant subpopulation of
high area to mass objects, strongly affected by non-gravitational
perturbations, it was actually necessary to solve also for dynamical parameters
describing these effects, that is to fit between 6 and 8 free parameters for
each orbit. The validation was based upon a set of real data, acquired from the
ESA Space Debris Telescope (ESASDT) at the Teide observatory (Canary Islands).
We proved that it is possible to assemble a set of sparse observations into a
set of objects with orbits, starting from a sparse time distribution of
observations, which would be compatible with a survey capable of covering the
region of interest in the sky just once per night. This could result in a
significant reduction of the requirements for a future telescope network, with
respect to what would have been required with the previously known algorithm
for correlation and orbit determination.Comment: 20 pages, 8 figure
Frequency based localization of structural discrepancies
The intent of modal analysis is to develop a reliable model of a structure by working with the analytical and experimental modal properties of frequency, damping and mode shape. In addition to identifying these modal properties, it would be desirable to determine spatially which parts of the structure are modelled poorly or well. It is shown how the pattern of discrepancies in the analytical and experimental test values for the pole and the driving point zero frequencies of a structure can be linked to discrepancies in the mass or stiffness of the structural elements. The success of the procedure depends on the numerical conditioning of a modal reference matrix. Strategies to insure adequate numerical conditioning require a formulation which avoids geometric and energy storage symmetries of the structure, and ignores structural elements which contribute negligibly small potential or kinetic energy to the excited modes. Physical insight into the numerical conditioning problem is provided by a numerical example and by localization of a mass discrepancy in a real structure based on lab tests
Innovative methods of correlation and orbit determination for space debris
We propose two algorithms to provide a full preliminary orbit of an
Earth-orbiting object with a number of observations lower than the classical
methods, such as those by Laplace and Gauss. The first one is the Virtual
debris algorithm, based upon the admissible region, that is the set of the
unknown quantities corresponding to possible orbits for objects in Earth orbit
(as opposed to both interplanetary orbits and ballistic ones). A similar method
has already been successfully used in recent years for the asteroidal case. The
second algorithm uses the integrals of the geocentric 2-body motion, which must
have the same values at the times of the different observations for a common
orbit to exist. We also discuss how to account for the perturbations of the
2-body motion, e.g., the effect.Comment: 18 page
Quench propagation in High Temperature Superconducting materials integrated in high current leads
High temperature superconductors (HTS) have been integrated in the high current leads for the Large Hadron Collider (LHC), under construction at CERN, in order to reduce the heat leak into the liquid helium bath due to the joule effect. The use of the HTS technology in the lower part of the current leads allowed to significantly reduce the heat charge on the cryogenic system. Hybrid current leads have been designed to fulfill the LHC requirements with respect to thermal load; several tests have been performed to study the lead behavior especially during a quench transient. Quench experiments have been performed at CERN on 13 kA prototypes to determine the adequate design and protection. In all the tests it is possible to know the temperature profile of the HTS only with the help of quench simulations that model the thermo-hydraulic processes during quench. The development of a theoretical model for the simulation allows reducing the number of test to perform and to scale the experimental result to other current lead sizes. In this work a theoretical quench model and a numerical code have been developed to compute the quench process and the thermal analysis in the HTS part of the current leads. The model approximates the heat balance equations with the finite difference method and considers the temperature dependence of material's properties. With this model it is possible to perform a thermal analysis of the HTS assembly in steady working condition as well as to study the resistive transition known as quench. The numerical approach is much more accurate than the analytical one, which involves a more approximated model with more physical approximations. In this work are given: the theoretical description of the model, its numerical implementation, the experimental validation and some simulation results
Light-time computations for the BepiColombo radioscience experiment
The radioscience experiment is one of the on board experiment of the Mercury
ESA mission BepiColombo that will be launched in 2014. The goals of the
experiment are to determine the gravity field of Mercury and its rotation
state, to determine the orbit of Mercury, to constrain the possible theories of
gravitation (for example by determining the post-Newtonian (PN) parameters), to
provide the spacecraft position for geodesy experiments and to contribute to
planetary ephemerides improvement. This is possible thanks to a new technology
which allows to reach great accuracies in the observables range and range rate;
it is well known that a similar level of accuracy requires studying a suitable
model taking into account numerous relativistic effects. In this paper we deal
with the modelling of the space-time coordinate transformations needed for the
light-time computations and the numerical methods adopted to avoid rounding-off
errors in such computations.Comment: 14 pages, 7 figures, corrected reference
Nanofriction behavior of cluster-assembled carbon films
We have characterized the frictional properties of nanostructured (ns) carbon
films grown by Supersonic Cluster Beam Deposition (SCBD) via an Atomic
Force-Friction Force Microscope (AFM-FFM). The experimental data are discussed
on the basis of a modified Amonton's law for friction, stating a linear
dependence of friction on load plus an adhesive offset accounting for a finite
friction force in the limit of null total applied load. Molecular Dynamics
simulations of the interaction of the AFM tip with the nanostructured carbon
confirm the validity of the friction model used for this system. Experimental
results show that the friction coefficient is not influenced by the
nanostructure of the films nor by the relative humidity. On the other hand the
adhesion coefficient depends on these parameters.Comment: 22 pages, 6 figures, RevTex
Vulcanization degree influence on the mechanical properties of Fiber Reinforced Elastomeric Isolators made with reactivated EPDM
Rubber is well known as the basic material for some structural devices, such as seaport fenders and seismic isolators. In practice, to seismically isolate a structure it is necessary to interpose between the foundation and the superstructure a rubber device that increases the period of the superstructure, a feature that allows the structure to be “transparent” to the seismic excitation. A seismic isolator is constituted typically by a package of several rubber pads 1–2 cm thick vertically interspersed with either steel laminas or FRP dry textiles suitably treated. In this latter case the isolator is called FREI (Fiber Reinforced Elastomeric Isolator). FREIs exhibit light weight, easy installation and low cost. In this study, recycled rubber in the form of reactivated EPDM has been used to produce very low cost FREIs, combined with glass fiber reinforcement. To be ready for structural application, the rubber used must be vulcanized correctly to properly create the polymer crosslinking. However, all rubber mechanical properties are strongly affected by curing temperature and curing time. Here, the mechanical properties of a typology of FREI conceived and produced by the authors in prototypes are evaluated through a series of experimental tests and numerical computations, taking into account the different levels of vulcanization degree. Shore A hardness test, uniaxial tensile test, and relaxation test have been conducted and verified through Finite Element (FE) modeling. All collected data allow to precisely determine the curing time and temperature to use in the industrial production to obtain optimal output mechanical properties for FREIs
- …