Fabrication and examination of oxidation resistance of zinc coated copper and brass components by chemical deposition

n this work, the structure and the oxidation resistance of Zn deposited Cu and brass metallic components are examined. The deposition was accomplished with pack cementation chemical deposition. The examination of the samples was performed with electron microscopy and X-ray diffraction analysis. It was found that coatings on Cu substrate consist of two layers with different Zn concentrations, while coatings on brass were single layered with almost constant Zn concentration. The presence of distinct Zn—Cu phases was revealed in both cases. The subjection of the as coated samples together with the uncoated substrates in air at 400ºC showed that both Zn coated samples have enhanced resistivity in such atmospheres, as most of the coating remained mostly unoxidised, and the substrates were fully protected. On the contrary, the bare substrates appear to have undergone severe damage as brittle oxides were formed on their surface.Publicad

The Challenges and Opportunities of Analogue Game-Based Learning

The report will be built on best existing practice in the area of game-based teaching and assessment from experts from all over Europe. It will include materials, resources, research and documented case studies of game-based approaches to teaching. Also, it will describe the challenges experts were facing during implementation of the practice and an articulated set of advice on how to confront the above challenges

Comparative study of corrosion performance of HVOF-sprayed coatings produced using conventional and suspension WC-Co feedstock.

Corrosion properties of nanostructured coatings deposited by suspension high-velocity oxy-fuel (S-HVOF) via an aqueous suspension of milled WC-Co powder were compared with conventional HVOF-sprayed coatings. Microstructural evaluations of these coatings included x-ray diffraction and scanning electron microscopy equipped with an energy-dispersive x-ray spectroscopy. The corrosion performance of AISI440C stainless steel substrate and the coatings was evaluated in a 3.5 wt.% NaCl aqueous solution at ~25 °C. The electrochemical properties of the samples were assessed experimentally, employing potentiodynamic polarization and electrochemical impedance spectroscopy. The potentiodynamic polarization results indicated that coatings produced by S-HVOF technique show lower corrosion resistance compared with the coatings produced by HVOF-JK (HVOF Jet Kote) and HVOF-JP (HVOF JP5000) techniques. Results are discussed in terms of corrosion mechanism, Bode and Nyquist plots, as well as equivalent circuit models of the coating–substrate system

Niobium and niobium-iron coatings on API 5LX 70 steel applied with HVOF

The present study aimed to create and characterize niobium and niobium-iron60% coatings applied to steel API 5L X70 using the hypersonic thermal spray process (HVOF). The morphologies of the coatings were analyzed using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and profilometry, while the coatings’ hardnesses was evaluated using the Vickers hardness test. The coatings’ corrosion resistance was evaluated by monitoring their open circuit potential and potentiodynamic polarization and performing electrochemical impedance spectroscopy in a 0.05 M NaCl solution. The results showed that the niobium-iron coating contained minor porosity regions, while such defects occurred over large regions of the niobium coating. In terms of corrosion resistance, the coatings obtained in this work promoted a reduction in the substrate’s corrosion rate, but the presence of discontinuities such as porosity compromised the barrier effects of these coatings

Structure property relationship of suspension thermally sprayed WC-Co nanocomposite coatings.

Tribomechanical properties of nanostructured coatings deposited by suspension high velocity oxy-fuel (S-HVOF) and conventional HVOF (Jet Kote) spraying were evaluated. Nanostructured S-HVOF coatings were obtained via ball milling of the agglomerated and sintered WC-12Co feedstock powder, which were deposited via an aqueous-based suspension using modified HVOF (TopGun) process. Microstructural evaluations of these hardmetal coatings included transmission electron microscopy, x-ray diffraction, and scanning electron microscopy equipped with energy dispersive x-ray spectroscopy. The nanohardness and modulus of the coated specimens were investigated using a diamond Berkovich nanoindenter. Sliding wear tests were conducted using a ball-on-flat test rig. Results indicated that low porosity coatings with nanostructured features were obtained. High carbon loss was observed, but coatings showed a high hardness up to 1000 HV2.9N. S-HVOF coatings also showed improved sliding wear and friction behavior, which were attributed to nanosized particles reducing ball wear in three-body abrasion and support of metal matrix due to uniform distribution of nanoparticles in the coating microstructure