The Effect of Mechanical Overloading on Surface Roughness of the Coronary Arteries

Background. Surface roughness can be used to identify disease within biological tissues. Quantifying surface roughness in the coronary arteries aids in developing treatments for coronary heart disease. This study investigates the effect of extreme physiological loading on surface roughness, for example, due to a rupture of an artery. Methods. The porcine left anterior descending (LAD) coronary arteries were dissected ex vivo. Mechanical overloading was applied to the arteries in the longitudinal direction to simulate extreme physiological loading. Surface roughness was calculated from three-dimensional reconstructed images. Surface roughness was measured before and after damage and after chemical processing to dehydrate tissue specimens. Results. Control specimens confirmed that dehydration alone results in an increase of surface roughness in the circumferential direction only. No variation was noted between the hydrated healthy and damaged specimens, in both the longitudinal ( and ) and circumferential ( and ) directions. After dehydration, an increase in surface roughness was noted for damaged specimens in both the longitudinal () and circumferential () directions. Conclusions. Mechanical overloading applied in the longitudinal direction did not significantly affect surface roughness. However, when combined with chemical processing, a significant increase in surface roughness was noted in both the circumferential and longitudinal directions. Mechanical overloading causes damage to the internal constituents of the arteries, which is significantly noticeable after dehydration of tissue

Objective Uniaxial Identification of Transition Points in Non-Linear Materials: Sample Application to Porcine Coronary Arteries and the Dependency of Their Pre- and Post-Transitional Moduli with Position

This study aimed to develop an objective method for the elastic characterisation of pre- and post-transitional moduli of left anterior descending (LAD) porcine coronary arteries. Methods Eight coronary arteries were divided into proximal, middle and distal test specimens. Specimens underwent uniaxial extension up to 3 mm. Force–displacement measurements were used to determine the induced true stress and stretch for each specimen. A local maximum of the stretch-true stress data was used to identify a transition point. Pre- and post-transitional moduli were calculated up to and from this point, respectively. Results The mean pre-transitional moduli for all specimens was 0.76 MPa, as compared to 4.86 MPa for the post-transitional moduli. However, proximal post-transitional moduli were significantly greater than that of middle and distal test specimens (p < 0.05). Conclusion Post-transitional uniaxial properties of the LAD are dependent on location along the artery. Further, it is feasible to objectively identify a transition point between pre- and post-transitional moduli

Multiscale three-dimensional surface reconstruction and surface roughness of porcine left anterior descending coronary arteries

The aim of this study was to investigate the multiscale surface roughness characteristics of coronary arteries, to aid in the development of novel biomaterials and bioinspired medical devices. Porcine left anterior descending coronary arteries were dissected ex vivo, and specimens were chemically fixed and dehydrated for testing. Surface roughness was calculated from three-dimensional reconstructed surface images obtained by optical, scanning electron and atomic force microscopy, ranging in magnification from 10× to 5500×. Circumferential surface roughness decreased with magnification, and microscopy type was found to influence surface roughness values. Longitudinal surface roughness was not affected by magnification or microscopy types within the parameters of this study. This study found that coronary arteries exhibit multiscale characteristics. It also highlights the importance of ensuring consistent microscopy parameters to provide comparable surface roughness values

Characterisation of coronary arteries: mechanical testing and three-dimensional imaging

Coronary artery disease is the leading cause of death in the UK. The studies in this thesis aim to influence the design of new biomaterials and medical devices used to treat coronary artery disease through the characterisation of left anterior descending (LAD) coronary arteries. The mechanical properties of arteries were quantified using dynamic mechanical analysis, at physiological relevant frequencies. The surface roughness of porcine LAD coronary arteries was quantitatively measured using optical, scanning electron (SEM) and atomic force microscopy at various magnifications to assess its multi-scale characteristics. Further, the effect of damage to surface roughness of biological tissue was investigated due to mechanical overloading and chemical processing, with a correction factor presented for the changes to surface roughness due to processing techniques associated with SEM. This thesis found LAD arteries to be viscoelastic, with a frequency-dependent storage moduli that does not vary along the length of the artery. Processing of tissue caused a significant increase in surface roughness, which must be considered for different microscopy techniques. The dehydration process had a greater effect on surface roughness than mechanical damage. The mechanical and surface roughness properties presented in this thesis can be specified for biomaterials to replicate natural, healthy coronary arteries

Additively manufactured versus conventionally pressed cranioplasty implants: An accuracy comparison

This article compared the accuracy of producing patient-specific cranioplasty implants using four different approaches. Benchmark geometry was designed to represent a cranium and a defect added simulating a craniectomy. An ‘ideal’ contour reconstruction was calculated and compared against reconstructions resulting from the four approaches –‘conventional’, ‘semi-digital’, ‘digital – non-automated’ and ‘digital – semi-automated’. The ‘conventional’ approach relied on hand carving a reconstruction, turning this into a press tool, and pressing titanium sheet. This approach is common in the UK National Health Service. The ‘semi-digital’ approach removed the hand-carving element. Both of the ‘digital’ approaches utilised additive manufacturing to produce the end-use implant. The geometries were designed using a non-specialised computer-aided design software and a semi-automated cranioplasty implant-specific computer-aided design software. It was found that all plates were clinically acceptable and that the digitally designed and additive manufacturing plates were as accurate as the conventional implants. There were no significant differences between the additive manufacturing plates designed using non-specialised computer-aided design software and those designed using the semi-automated tool. The semi-automated software and additive manufacturing production process were capable of producing cranioplasty implants of similar accuracy to multi-purpose software and additive manufacturing, and both were more accurate than handmade implants. The difference was not of clinical significance, demonstrating that the accuracy of additive manufacturing cranioplasty implants meets current best practice

Effect of glutaraldehyde based cross-linking on the viscoelasticity of mitral valve basal chordae tendineae

Background Mitral valve failure can require repair or replacement. Replacement bioprosthetic valves are treated with glutaraldehyde prior to implantation. The aim of this study was to determine the changes in mechanical properties following glutaraldehyde fixation of mitral valve chordae. Methods To investigate the impact of glutaraldehyde on mitral valve chordae, 24 basal chordae were dissected from four porcine hearts. Anterior and posterior basal (including strut) chordae were used. All 24 chordae were subjected to a sinusoidally varying load (mean level 2N, dynamic amplitude 2N) over a frequency range of 0.5–10 Hz before and after glutaraldehyde treatment. Results The storage and loss modulus of all chordal types decreased following glutaraldehyde fixation. The storage modulus ranged from: 108 to 119 MPa before fixation and 67.3–87.4 MPa following fixation for basal chordae; 52.3–58.4 MPa before fixation and 47.9–53.5 MPa following fixation for strut chordae. Similarly, the loss modulus ranged from: 5.47 to 6.25 MPa before fixation and 3.63–4.94 MPa following fixation for basal chordae; 2.60–2.97 MPa before fixation and 2.31–2.93 MPa following fixation for strut chordae. Conclusion The viscoelastic properties of mitral valve chordae are affected by glutaraldehyde fixation; in particular, the reduction in storage moduli decreased with an increase in chordal diameter

Hyperspectral chemical imaging reveals spatially varied degradation of polycarbonate urethane (PCU) biomaterials

Hyperspectral chemical imaging (HCI) is an emerging technique which combines spectroscopy with imaging. Unlike traditional point spectroscopy, which is used in the majority of polymer biomaterial degradation studies, HCI enables the acquisition of spatially localised spectra across the surface of a material in an objective manner. Here, we demonstrate that attenuated total reflectance Fourier transform infra-red (ATR-FTIR) HCI reveals spatial variation in the degradation of implantable polycarbonate urethane (PCU) biomaterials. It is also shown that HCI can detect possible defects in biomaterial formulation or specimen production; these spatially resolved images reveal regional or scattered spatial heterogeneity. Further, we demonstrate a map sampling method, which can be used in time-sensitive scenarios, allowing for the investigation of degradation across a larger component or component area. Unlike imaging, mapping does not produce a contiguous image, yet grants an insight into the spatial heterogeneity of the biomaterial across a larger area. These novel applications of HCI demonstrate its ability to assist in the detection of defective manufacturing components and lead to a deeper understanding of how a biomaterial’s chemical structure changes due to implantation. Statement of Signifance The human body is an aggressive environment for implantable devices and their biomaterial components. Polycarbonate urethane (PCU) biomaterials in particular were investigated in this study. Traditionally one or a few points on the PCU surface are analysed using ATR-FTIR spectroscopy. However the selection of acquisition points is susceptible to operator bias and critical information can be lost. This study utilises hyperspectral chemical imaging (HCI) to demonstrate that the degradation of a biomaterial varies spatially. Further, HCI revealed spatial variations of biomaterials that were not subjected to oxidative degradation leading to the possibility of HCI being used in the assessment of biomaterial formulation and/or component production

The design of additively manufactured lattices to increase the functionality of medical implants

The rise of antibiotic resistant bacterial species is driving the requirement for medical devices that minimise infection risks. Antimicrobial functionality may be achieved by modifying the implant design to incorporate a reservoir that locally releases a therapeutic. For this approach to be successful it is critical that mechanical functionality of the implant is maintained. This study explores the opportunity to exploit the design flexibilities possible using additive manufacturing to develop porous lattices that maximise the volume available for drug loading while maintaining load-bearing capacity of a hip implant. Eight unit cell types were initially investigated and a volume fraction of 30% was identified as the lowest level at which all lattices met the design criteria in ISO 13314. Finite element analysis (FEA) identified three lattice types that exhibited significantly lower displacement (10-fold) compared with other designs; Schwartz primitive, Schwartz primitive pinched and cylinder grid. These lattices were additively manufactured in Ti-6Al-4V using selective laser melting. Each design exceeded the minimum strength requirements for orthopaedic hip implants according to ISO 7206-4. The Schwartz primitive (Pinched) lattice geometry, with 10% volume fill and a cubic unit cell period of 10, allowed the greatest void volume of all lattice designs whilst meeting the fatigue requirements for use in an orthopaedic implant (ISO 7206-4). This paper demonstrates an example of how additive manufacture may be exploited to add additional functionality to medical implants

Morphology and function of the forelimb in arboreal frogs: specializations for grasping ability.

Frogs are characterized by a unique morphology associated with their saltatory lifestyle. Although variation in the form and function of the pelvic girdle and associated appendicular system related to specialized locomotor modes such as swimming or burrowing has been documented, the forelimbs have typically been viewed as relatively unspecialized. Yet, previous authors have noted versatility in forelimb function among arboreal frogs associated with feeding. Here we study the morphology and function of the forelimb and hand during locomotion in two species of arboreal frogs (Litoria caerulea and Phyllomedusa bicolor). Our data show a complex arrangement of the distal forelimb and hand musculature with some notable differences between species. Analyses of high‐speed video and video fluoroscopy recordings show that forelimbs are used in alternating fashion in a diagonal sequence footfall pattern and that the position of the hand is adjusted when walking on substrates of different diameters. Electromyographic recordings show that the flexors of the hand are active during substrate contact, suggesting the use of gripping to generate a stabilizing torque. Measurements of grasping forces in vivo and during stimulation experiments show that both species, are capable of executing a so‐called power grip but also indicates marked differences between species, in the magnitude of forces generated. Stimulation experiments showed an increased control of digit flexion in the more specialized of the two species, allowing it to execute a precision grip paralleled only by that seen in primates.Fil: Manzano, Adriana Silvina. Provincia de Entre Ríos. Centro de Investigaciones Científicas y Transferencia de Tecnología a la Producción. Universidad Autónoma de Entre Ríos. Centro de Investigaciones Científicas y Transferencia de Tecnología a la Producción. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Santa Fe. Centro de Investigaciones Científicas y Transferencia de Tecnología a la Producción; ArgentinaFil: Abdala, Virginia Sara Luz. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Tucumán. Instituto de Biodiversidad Neotropical. Universidad Nacional de Tucumán. Facultad de Ciencias Naturales e Instituto Miguel Lillo. Instituto de Biodiversidad Neotropical. Instituto de Biodiversidad Neotropical; ArgentinaFil: Herrel, Anthony. University of Antwerp; Bélgic