Normal and abnormal human vestibular ocular function

The major motivation of this research is to understand the role the vestibular system plays in sensorimotor interactions which result in spatial disorientation and motion sickness. A second goal was to explore the range of abnormality as it is reflected in quantitative measures of vestibular reflex responses. The results of a study of vestibular reflex measurements in normal subjects and preliminary results in abnormal subjects are presented in this report. Statistical methods were used to define the range of normal responses, and determine age related changes in function

Limit cycles of a flexible shaft with hydrodynamic journal bearings in unstable regimes

A symmetric 3 mass rotor supported on hydrodynamic bearings is described. An approximate method of representing finite bearings is used to calculate bearing forces. As the method sums forces from a number of independent circular lobes lemon 3 and 4 lobe bearings are taken into account. The calculations are based on an axial groove bearing. Linear analysis precedes nonlinear simulation of some unstable conditions. The demonstration of small limit cycles suggests that necessarily flexible rotors e.g., helicopter tail rotors, may be practical without either tilt pad bearings or external dampers

Age-related changes in human posture control: Motor coordination tests

Postural responses to support surface displacements were measured in 214 normal human subjects ranging in age from 7 to 81 years. Motor tests measured leg muscle Electromyography (EMG) latencies, body sway, and the amplitude and timing of changes in center of pressure displacements in response to sudden forward and backward horizontal translations of the support surface upon which the subjects stood. There were small increases in both EMG latencies and the time to reach the peak amplitude of center of pressure responses with increasing age. The amplitude of center of pressure responses showed little change with age if the amplitude measures were normalized by a factor related to subject height. In general, postural responses to sudden translations showed minimal changes with age, and all age related trends which were identified were small relative to the variability within the population

Estimates of the duration of untreated acute malnutrition in children from Niger.

Expected incidence of acute malnutrition is the most appropriate measure for projecting the needs of a nutritional treatment program over time in terms of staffing, food, and other treatments, but direct estimation of incidence is rarely feasible at the onset of an intervention. While incidence may be approximated as prevalence/average duration, ethical constraints preclude measurement of the duration of acute malnutrition in the absence of treatment. The authors used a compartmental model to estimate the duration of untreated moderate acute malnutrition (MAM) and severe acute malnutrition (SAM) in children aged 6-60 months. The model was informed by data from a community-based cohort of children in Niger followed from August 2006 to March 2007. Maximum likelihood estimates for the duration of untreated MAM, defined by weight-for-height z score and middle upper arm circumference, were 75-81 days and 101-116 days, respectively. The duration of untreated SAM, defined by weight-for-height z score, was 45 days. The duration of untreated MAM appears to have been shorter among children aged 6-35 months compared with those aged 36-60 months. Such estimates of the duration, and thus incidence, of untreated malnutrition can be used to improve projections of program needs and estimates of the global burden of acute malnutrition

Structure, bonding and morphology of hydrothermally synthesised xonotlite

The authors have systematically investigated the role of synthesis conditions upon the structure and morphology of xonotlite. Starting with a mechanochemically prepared, semicrystalline phase with Ca/Si=1, the authors have prepared a series of xonotlite samples hydrothermally, at temperatures between 200 and 250 degrees C. Analysis in each case was by X-ray photoelectron spectroscopy, environmental scanning electron microscopy and X-ray diffraction. The authors’ use of a much lower water/solid ratio has indirectly confirmed the ‘through solution’ mechanism of xonotlite formation, where silicate dissolution is a key precursor of xonotlite formation. Concerning the role of temperature, too low a temperature (~200 degrees C) fails to yield xonotlite or leads to increased number of structural defects in the silicate chains of xonotlite and too high a temperature (>250 degrees C) leads to degradation of the xonotlite structure, through leaching of interchain calcium. Synthesis duration meanwhile leads to increased silicate polymerisation due to diminishing of the defects in the silicate chains and more perfect crystal morphologies

Evaluation of wind tunnel performance testings of an advanced 45 deg swept 8-bladed propeller at Mach numbers from 0.45 to 0.85

The increased emphasis of fuel conservation in the world and the rapid increase in the cost of jet fuel has stimulated a series of studies of both conventional and unconventional propulsion systems for commercial aircraft. The results of these studies indicate that a fuel saving of 15 to 30 percent may be realized by the use of an advanced high-speed turboprop (Prop-Fan) compared to aircraft equipped with high bypass turbofan engines of equivalent technology. The Prop-Fan propulsion system is being investigated as part of the NASA Aircraft Energy Efficient Program. This effort includes the wind tunnel testing of a series of 8 and 10-blade Prop-Fan models incorporate swept blades. Test results indicate efficiency levels near the goal of 80 percent at Mach 0.8 cruise and an altitude of 10.67 km (35,000 ft). Each successive swept model has shown improved efficiency relative to the straight blade model. The fourth model, with 45 deg swept blades reported herein, shows a net efficiency of 78.2 at the design point with a power loading of 301 kW/sq meter and a tip speed of 243.8 m/sec (800 ft/sec.)

Blade loss transient dynamics analysis. Volume 3: User's manual for TETRA program

The users manual for TETRA contains program logic, flow charts, error messages, input sheets, modeling instructions, option descriptions, input variable descriptions, and demonstration problems. The process of obtaining a NASTRAN 17.5 generated modal input file for TETRA is also described with a worked sample

Float-polishing process and analysis of float-polished quartz

A fluid-mechanical model is developed for the float-polishing process. In this model laminar flow between the sample and the lap results in pressure gradients at the grooves that support the sample on a fluid layer. The laminar fluid motion also produces supersmooth, damage-free surfaces. Quartz substrates for applications in high-stress environments were float polished, and their surfaces were analyzed by optical scatterometry, photoacoustic spectroscopy, and atomic force microscopy. The removal of 100 µm of material by a lapping-polishing process, with final float polishing, left low levels of subsurface damage, with a surface roughness of approximately 0.2-nm rms

Calcium kinetics in Vitamin D deficiency rickets

No Abstrac

New nickel-base wrought superalloy with applications up to 1253 K (1800 F)

Alloy possesses combination of high tensile strength at low and intermediate temperatures to 1033 K with good rupture strength at high temperatures to 1255 K. Alloy has promise for turbine disk application in future gas turbine engines and for wrought integrally bladed turbine wheel; thickness and weight of disk portion of wheel could be reduced