348 research outputs found
Recommended from our members
Modeling the contact mechanics of hydrogels
A computationally lean model for the coarse-grained description of contact mechanics of hydrogels is proposed and characterized. It consists of a simple bead-spring model for the interaction within a chain, potentials describing the interaction between monomers and mold or confining walls, and a coarse-grained potential reflecting the solvent-mediated effective repulsion between non-bonded monomers. Moreover, crosslinking only takes place after the polymers have equilibrated in their mold. As such, the model is able to reflect the density, solvent quality, and the mold hydrophobicity that existed during the crosslinking of the polymers. Finally, such produced hydrogels are exposed to sinusoidal indenters. The simulations reveal a wavevector-dependent effective modulus E*(q) with the following properties: (i) stiffening under mechanical pressure, and a sensitivity of E*(q) on (ii) the degree of crosslinking at large wavelengths, (iii) the solvent quality, and (iv) the hydrophobicity of the mold in which the polymers were crosslinked. Finally, the simulations provide evidence that the elastic heterogeneity inherent to hydrogels can suffice to pin a compressed hydrogel to a microscopically frictionless wall that is undulated at a mesoscopic length scale. Although the model and simulations of this feasibility study are only two-dimensional, its generalization to three dimensions can be achieved in a straightforward fashion. © 2019 by the authors
The spectral problem for the dispersionless Camassa-Holm equation
We present a spectral and inverse spectral theory for the zero dispersion spectral problem associated with the Camassa-Holm equation. This is an alternative approach to that in [10] by Eckhardt and Teschl
Structural models for the Si(553)-Au atomic chain reconstruction
Recent photoemission experiments on the Si(553)-Au reconstruction show a
one-dimensional band with a peculiar ~1/4 filling. This band could provide an
opportunity for observing large spin-charge separation if electron-electron
interactions could be increased. To this end, it is necessary to understand in
detail the origin of this surface band. A first step is the determination of
the structure of the reconstruction. We present here a study of several
structural models using first-principles density functional calculations. Our
models are based on a plausible analogy with the similar and better known
Si(557)-Au surface, and compared against the sole structure proposed to date
for the Si(553)-Au system [Crain JN et al., 2004 Phys. Rev. B 69 125401 ].
Results for the energetics and the band structures are given. Lines for the
future investigation are also sketched
Recommended from our members
Single layer graphene induces load-bearing molecular layering at the hexadecane-steel interface
The influence of a single layer graphene on the interface between a polished steel surface and the model lubricant hexadecane is explored by high-resolution force microscopy. Nanometer-scale friction is reduced by a factor of three on graphene compared to the steel substrate, with an ordered layer of hexadecane adsorbed on the graphene. Graphene furthermore induces a molecular ordering in the confined lubricant with an average range of 4-5 layers and with a strongly increased load-bearing capacity compared to the lubricant on the bare steel substrate. © 2019 IOP Publishing Ltd
Observation of individual molecules trapped on a nanostructured insulator
For the first time, ordered polar molecules confined in monolayer-deep
rectangular pits produced on an alkali halide surface by electron irradiation
have been resolved at room temperature by non-contact atomic force microscopy.
Molecules self-assemble in a specific fashion inside pits of width smaller than
15 nm. By contrast no ordered aggregates of molecules are observed on flat
terraces. Conclusions regarding nucleation and ordering mechanisms are drawn.
Trapping in pits as small as 2 nm opens a route to address single molecules
Distance dependence of force and dissipation in non-contact atomic force microscopy on Cu(100) and Al(111)
The dynamic characteristics of a tip oscillating in the nc-AFM mode in close
vicinity to a Cu(100)-surface are investigated by means of phase variation
experiments in the constant amplitude mode. The change of the quality factor
upon approaching the surface deduced from both frequency shift and excitation
versus phase curves yield to consistent values. The optimum phase is found to
be independent of distance. The dependence of the quality factor on distance is
related to 'true' damping, because artefacts related to phase misadjustment can
be excluded. The experimental results, as well as on-resonance measurements at
different bias voltages on an Al(111) surface, are compared to Joule
dissipation and to a model of dissipation in which long-range forces lead to
viscoelastic deformations
Self-Doping of Gold Chains on Silicon: A New Structural Model for Si(111)5x2-Au
A new structural model for the Si(111)5x2-Au reconstruction is proposed and
analyzed using first-principles calculations. The basic model consists of a
"double honeycomb chain" decorated by Si adatoms. The 5x1 periodicity of the
honeycomb chains is doubled by the presence of a half-occupied row of Si atoms
that partially rebonds the chains. Additional adatoms supply electrons that
dope the parent band structure and stabilize the period doubling; the optimal
doping corresponds to one adatom per four 5x2 cells, in agreement with
experiment. All the main features observed in scanning tunneling microscopy and
photoemission are well reproduced.Comment: 4 pages, 4 figures, to appear in Phys. Rev. Lett. (preprint with high
quality figures available at
http://cst-www.nrl.navy.mil/~erwin/papers/ausi111
Ageing of a Microscopic Sliding Gold Contact at Low Temperatures
Nanometer-scale friction measurements on a Au(111) surface have been performed at temperatures between 30 and 300 K by means of atomic force microscopy. Stable stick slip with atomic periodicity is observed at all temperatures, showing only weak dependence on temperature between 300 and 170 K. Below 170 K, friction increases with time and a distortion of the stick-slip characteristic is observed. Low friction and periodic stick slip can be reestablished by pulling the tip out of contact and subsequently restoring the contact. A comparison with molecular dynamics simulations indicates that plastic deformation within a growing gold junction leads to the observed frictional behavior at low temperatures. The regular stick slip with atomic periodicity observed at room temperature is the result of a dynamic equilibrium shape of the contact, as microscopic wear damage is observed to heal in the sliding contact
Atomic structure of alkali halide surfaces
The atomic structure of surfaces of alkali halide crystals has been revealed by means of high-resolution dynamic force microscopy. True atomic resolution is demonstrated both on steps surrounding islands or pits, and on a chemically mixed crystal. We have directly observed the enhanced interaction at low-coordinated sites by force microscopy. The growth of NaCl films on metal surfaces and radiation damage in a KBr surface is discussed based on force microscopy results. The damping of the tip oscillation in dynamic force microscopy might provide insight into dissipation processes on the atomic scale. Finally, we present atomically resolved images of wear debris found after scratching a KBr surfac
- …