Loss of strength in Ni3Al at elevated temperatures

Stress decrease above the stress peak temperature (750 K) is studied in h123i single crystals of Ni3(Al, 3 at.% Hf ). Two thermally activated deformation mechanisms are evidenced on the basis of stress relaxation and strain rate change experiments. From 500 to 1070 K, the continuity of the activation volume/temperature curves reveals a single mechanism of activation enthalpy 3.8 eV/atom and volume 90 b3 at 810K with an athermal stress of 330 MPa. Over the very same temperature interval, impurity or solute diffusion towards dislocation cores is evidenced through serrated yielding, peculiar shapes of stress–strain curves while changing the rate of straining and stress relaxation experiments. This complicates the identification of the deformation mechanism, which is likely connected with cube glide. From 1070 to 1270 K, the high-temperature mechanism has an activation enthalpy and volume of 4.8 eV/atom and 20 b3, respectively, at 1250 K

Influence of Y2O3 and Fe2Y additions on the formation of nano-scale oxide particles and the mechanical properties of an ODS RAF steel

The main goal of this work was to manufacture an oxide dispersion strengthened (ODS) reduced activation ferritic steel from a pre-alloyed, gas atomised Fe-14Cr-2W-0.2Ti (in wt.%) powder mechanically alloyed with either 0.3%Y2O(3) or 0.5%Fe2Y particles and consolidated by hot isostatic pressing, and to investigate its microstructure, microhardness and Charpy impact properties

Microstructure and mechanical properties of an ODS RAF steel fabricated by hot extrusion or hot isostatic pressing

Ingots of an oxide dispersion strengthened reduced activation ferritic steel with the Fe-14Cr-2W-0.3Ti-0.3Y(2)O(3) chemical composition (in wt.%) were synthesized by mechanical alloying of elemental powders with 0.3 wt.% Y2O3 particles in a planetary ball mill, in a hydrogen atmosphere. and compacted by either hot extrusion or hot isostatic pressing. The microstructures of the obtained materials were characterized by means of light microscopy, transmission electron microscopy and chemical analyses. The mechanical properties were evaluated by means of Vickers microhardness measurements and tensile tests. It was found that the microstructure of both materials is composed of ferritic grains having a submicron size and containing nanometric Y-Ti-O oxide particles with a mean size of about 10 nm, uniformly distributed in the matrix. The oxide particles in the hot extruded steel were identified as YTiO3 phase. In larger (>10 nm) oxide particles Cr was found next to Ti, Y and O. The steel produced by hot extrusion exhibits much higher tensile strength and hardness at low to moderate temperatures, as compared to the steel fabricated by hot isostatic pressing, which was mainly attributed to smaller pores but also to more severe work hardening in the case of the hot extruded steel. (C) 2011 Elsevier B.V. All rights reserved

Microstructure and tensile properties of ODS ferritic steels mechanically alloyed with Fe2Y

An oxide dispersion strengthened ODS ferritic steel has been produced by mechanical alloying of Fe–14Cr–2W–0.2Ti (wt.%) prealloyed powder with 0.55 (wt.%) Fe2Y intermetallic particles and consolidated by hot isostatic pressing. The microstructure after thermal treatments confirms the homogeneous precipitation of Y-Ti oxides with nanometric sizes. Tensile properties as a function of the testing temperature from room temperature to 973 K have been measured and the results are discussed with respect to similar ODS ferritic steels fabricated by a powder metallurgy route using Y2O3 powder

Review on the EFDA work programme on nano-structured ODS RAF steels

This proceeding is: The 14th International Conference on Fusion Reactor Materials (ICFRM-14) was held at the Sapporo Convention Center in Sapporo, Japan from 7 to 12 September 2009.The 2008─2009 work programme of the European research project on nano-structured oxide dispersion strengthened (ODS) reduced activation ferritic (RAF) steels is being organized along the four following programmatic lines: (1) improve the present generation of nano-structured ODS RAF steels; (2) start the industrial fabrication of the present generation of nano-structured ODS RAF steels; (3) develop an optimised generation of nano-structured and nano-grained ODS RAF steels; (4) investigate the stability of present and optimised generation of nano-structured ODS RAF steels under creep and irradiation. This paper presents the main objectives of current R&D activities being performed within the European research project on nano-structured ODS RAF steels, the main obtained results and the main future activities in the case of the four programmatic lines mentioned just above.This work, supported by the European Communities, was carried out within the framework of the European Fusion Development Agreement.Publicad

Design of the ITER high-frequency magnetic diagnostic coils

This paper is an overview of work carried out on the design of the ITER high-frequency magnetic diagnostic coil (HF sensor). In the first part, the ITER requirements for the HF sensor are presented. In the second part, the ITER reference design of the HF sensor has been assessed and showed some potential weaknesses, which led us to the conclusion that alternative designs could usefully be examined. Several options have been explored, and are presented in the third part: (a) direct laser cutting a metallic tube, (b) stacking of plane windings manufactured from a tungsten plate by electrical discharge machining, (c) coil using the conventional spring manufacture. In the fourth part, sensors using the low temperature co-fired ceramic technology (LTCC) are presented: (d) monolithic 1D magnetic flux sensors based on LTCC technology, and (e) monolithic 3D magnetic flux sensors based on the same LTCC technology. The solution which showed the best results is the monolithic 3D magnetic flux sensor based on LTCC. (C) 2011 Elsevier B.V. All rights reserved