Mechanical properties of polycrystalline graphene based on a realistic atomistic model

Graphene can at present be grown at large quantities only by the chemical vapor deposition method, which produces polycrystalline samples. Here, we describe a method for constructing realistic polycrystalline graphene samples for atomistic simulations, and apply it for studying their mechanical properties. We show that cracks initiate at points where grain boundaries meet and then propagate through grains predominantly in zigzag or armchair directions, in agreement with recent experimental work. Contrary to earlier theoretical predictions, we observe normally distributed intrinsic strength (~ 50% of that of the mono-crystalline graphene) and failure strain which do not depend on the misorientation angles between the grains. Extrapolating for grain sizes above 15 nm results in a failure strain of ~ 0.09 and a Young's modulus of ~ 600 GPa. The decreased strength can be adequately explained with a conventional continuum model when the grain boundary meeting points are identified as Griffith cracks.Comment: Accepted for Physical Review B; 5 pages, 4 figure

Graphene edge from A to Z - and the origins of nanotube chirality

The energy of arbitrary graphene edge is derived in analytical form. It contains a "chemical phase shift", determined by the chemical conditions at the edge. Direct atomistic computations support the universal nature of the relationship. Definitive for graphene formation, shapes of the voids or ribbons, this has further important implications for nanotube chirality selection and control by chemical means, at the nucleation stage.Comment: 12 pages, 3 figure

Development and operation of research-scale III-V nanowire growth reactors

III-V nanowires are useful platforms for studying the electronic and mechanical properties of materials at the nanometer scale. However, the costs associated with commercial nanowire growth reactors are prohibitive for most research groups. We developed hot-wall and cold-wall metal organic vapor phase epitaxy (MOVPE) reactors for the growth of InAs nanowires, which both use the same gas handling system. The hot-wall reactor is based on an inexpensive quartz tube furnace and yields InAs nanowires for a narrow range of operating conditions. Improvement of crystal quality and an increase in growth run to growth run reproducibility are obtained using a homebuilt UHV cold-wall reactor with a base pressure of 2 X 10$^{-9}$ Torr. A load-lock on the UHV reactor prevents the growth chamber from being exposed to atmospheric conditions during sample transfers. Nanowires grown in the cold-wall system have a low defect density, as determined using transmission electron microscopy, and exhibit field effect gating with mobilities approaching 16,000 cm$^2$(V.s).Comment: Related papers at http://pettagroup.princeton.ed

Impact of rabies vaccination history on attainment of an adequate antibody titre among dogs tested for International Travel Certification, Israel - 2010-2014

Rabies is endemic in wildlife or domestic carnivore populations globally. Infection of domestic dogs is of particular concern in many areas. In regions where domestic animals are at risk of exposure to rabies virus, dogs should be routinely vaccinated against rabies to protect both pet and human populations. Many countries require demonstration of an adequate level of serum rabies neutralizing antibodies to permit entry of dogs during international travel. We analysed rabies titres of dogs seeking travel certification in Israel to assess demographic and vaccine history factors associated with antibody titres below the acceptable threshold for travel certification. Having received only one previous rabies vaccination and a longer duration since the most recent vaccination was received were primary risk factors for not achieving an adequate rabies virus neutralizing antibody titre for travel certification. These risk factors had stronger effects in younger animals, but were consistent for dogs of all ages. In particular, these findings reiterate the importance of administering at least two rabies vaccinations (the primo vaccination and subsequent booster) to ensure population-level protection against rabies in dogs globally

Atomistic Simulations of Nanotube Fracture

The fracture of carbon nanotubes is studied by atomistic simulations. The fracture behavior is found to be almost independent of the separation energy and to depend primarily on the inflection point in the interatomic potential. The rangle of fracture strians compares well with experimental results, but predicted range of fracture stresses is marketly higher than observed. Various plausible small-scale defects do not suffice to bring the failure stresses into agreement with available experimental results. As in the experiments, the fracture of carbon nanotubes is predicted to be brittle. The results show moderate dependence of fracture strength on chirality.Comment: 12 pages, PDF, submitted to Phy. Rev.

Extreme structure and spontaneous lift of spin degeneracy in doped perforated bilayer graphenes

Extreme structure and spin states of doped and undoped perforated bigraphenes was studied using DFT simulations. It was found that folded nanopores possess extremely high curvature of 0.34 Å−1. Dramatic structural deformation causes severe changes of the chemical properties of carbon atoms localized at the nanopores converting the folded edges to local oxidative fragments. It was found that asymmetrical coordination of either Li, Ca, or Al to the nanopores is coupled with electron transfer from metal to edge carbon atoms and breakdown of local inversion symmetry. Li-, Ca-, and Al-doped perforated AA bigraphene revealed ferromagnetic spin ordering with magnetic moments of 0.38, 0.14, and 0.32μB/unit cell, respectively, and spin polarization energy gain of 0.037eV for Ca-doped superlattice. It was shown that ferromagnetic spin ordering of bigraphene nanopores contradicts to the Nagaoka's theorem, which excludes strong electron correlations as a reason of spin polarization. Spontaneous lift of spin degeneracy was interpreted in terms of perturbing intense local electrostatic fields from extra electron charges localized at the nanopore edges, coupled with breakdown of space inversion and local translation invariances. It was shown that spin energy splitting is proportional to the matrix elements calculated on Bloch states with opposite wavevectors and perturbing electrostatic fields

Transmission Through Carbon Nanotubes With Polyhedral Caps

We study electron transport between capped carbon nanotubes and a substrate, and relate the transmission probability to the local density of states in the cap. Our results show that the transmission probability mimics the behavior of the density of states at all energies except those that correspond to localized states in the cap. Close proximity of a substrate causes hybridization of the localized state. As a result, new transmission paths open from the substrate to nanotube continuum states via the localized states in the cap. Interference between various transmission paths gives rise to antiresonances in the transmission probability, with the minimum transmission equal to zero at energies of the localized states. Defects in the nanotube that are placed close to the cap cause resonances in the transmission probability, instead of antiresonances, near the localized energy levels. Depending on the spatial position of defects, these resonant states are capable of carrying a large current. These results are relevant to carbon nanotube based studies of molecular electronics and probe tip applications

Nonlinear resonance in a three-terminal carbon nanotube resonator

The RF-response of a three-terminal carbon nanotube resonator coupled to RF-transmission lines is studied by means of perturbation theory and direct numerical integration. We find three distinct oscillatory regimes, including one regime capable of exhibiting very large hysteresis loops in the frequency response. Considering a purely capacitive transduction, we derive a set of algebraic equations which can be used to find the output power (S-parameters) for a device connected to transmission lines with characteristic impedance $Z_0$.Comment: 16 pages, 8 figure