Electrochemosensor for Trace Analysis of Perfluorooctanesulfonate in Water Based on a Molecularly Imprinted Poly(o-phenylenediamine) Polymer

This work is aimed at developing an electrochemical sensor for the sensitive and selective detection of trace levels of perfluorooctanesulfonate (PFOS) in water. Contamination of waters by perfluorinated alkyl substances (PFAS) is a problem of global concern due to their suspected toxicity and ability to bioaccumulate. PFOS is the perfluorinated compound of major concern, as it has the lowest suggested control concentrations. The sensor reported here is based on a gold electrode modified with a thin coating of a molecularly imprinted polymer (MIP), prepared by anodic electropolymerization of o-phenylenediamine (o-PD) in the presence of PFOS as the template. Activation of the sensor is achieved by template removal with suitable a solvent mixture. Voltammetry, a quartz crystal microbalance, scanning electron microscopy and elemental analysis were used to monitor the electropolymerization process, template removal, and binding of the analyte. Ferrocenecarboxylic acid (FcCOOH) has been exploited as an electrochemical probe able to generate analytically useful voltammetric signals by competing for the binding sites with PFOS, as the latter is not electroactive. The sensor has a low detection limit (0.04 nM), a satisfactory selectivity, and is reproducible and repeatable, giving analytical results in good agreement with those obtained by HPLC-MS/MS analyses

Trace elements in size-segregated urban aerosol in relation to the anthropogenic emission sources and the resuspension

Size segregated particulate samples of atmospheric aerosols in urban site of continental part of Balkans were collected during 6 months in 2008. Six stages impactor in the size ranges: Dp ≤ 0.49 μm, 0.49 < Dp ≤ 0.95 μm, 0.95 < Dp ≤ 1.5 μm, 1.5 < Dp ≤ 3.0 μm, 3.0 < Dp ≤ 7.2 μm, and 7.2 < Dp ≤ 10.0 μm was applied for sampling. ICP-MS was used to quantify elements: Al, As, Bi, Ca, Cd, Co, Cr, Cu, Fe, Ga, K, Li, Na, Ni, Mg, Mn, Pb, Sb, V, and Zn. Two main groups of elements were investigated: (1) K, V, Ni, Zn, Pb, As, and Cd with high domination in nuclei mode indicating the combustion processes as a dominant sources and (2) Al, Fe, Ca, Mg, Na, Cr, Ga, Co, and Li in coarse mode indicating mechanical processes as their main origin. The strictly crustal origin is for Mg, Fe, Ca, and Co while for As, Cd, K, V, Ni, Cu, Pb, and Zn dominates the anthropogenic influence. The PCA analysis has shown that main contribution is of resuspension (PC1, σ2 ≈ 30 %) followed by traffic (PC2, σ2 ≈ 20 %) that are together contributing around 50 % of elements in the investigated urban aerosol. The EF model shows that major origin of Cd, K, V, Ni, Cu, Pb, Zn, and As in the fine mode is from the anthropogenic sources while increase of their contents in the coarse particles indicates their deposition from the atmosphere and soil contamination. This approach is useful for the assessment of the local resuspension influence on element’s contents in the aerosol and also for the evaluation of the historical pollution of soil caused by deposition of metals from the atmosphere

Enrichment of organic pollutants in the sea surface microlayer (SML) at Terra Nova Bay, Antarctica: influence of SML on superficial snow composition.

Concentrations of dissolved and particle-associated n-alkanes, phthalates and polycyclic aromatic hydrocarbons (PAHs) were measured in sea surface microlayer (SML) and sub-surface water (SSL) samples collected in the coastal area of Terra Nova Bay, Antarctica, during the Austral spring 1998/1999. SML concentrations of the selected organic compounds were higher than SSL values and the enrichment factors were greater in the particulate phase than in the dissolved phase. During the same campaign, ‘‘fresh’’ snow samples, collected at different altitudes (from sea level up to 2670 m) near the coast on Mt Melbourne, immediately after a snowy event, were analysed in order to provide more information on air/sea exchange processes. The same classes of organic compounds found in sea water were also present in ‘‘fresh’’ snow samples. The surfactant fluorescent organic matter (SFOM), adsorbed on the microdrop aerosol surface, could be considered the main constituent of the enrichment and the carrier at higher altitudes of organic compounds. In fact, hydrocarbons (n-alkanes and PAHs), which are not surfactants like phthalates, could interact with SFOM and follow the same fate

Electrochemical preconcentration coupled with spectroscopic techniques for trace lead analysis in olive oils

In this paper we present a novel combined electrochemical-spectroscopic approach suitable to monitor trace levels of heavy metals directly in edible oils. The method is based on the electrochemical preconcentration/extraction of the analyte from the tested real matrix by cathodic deposition onto a Pt working electrode, then transfer and anodic re-oxidation of the metallic deposit to a “clean” aqueous solution, suitable for the subsequent spectroscopic analysis. The procedure has been here focused to the determination of lead in extra virgin olive oil (EVOO), performed by applying ICP-QMS or GFAAS techniques. To this aim, the EVOO samples were mixed with proper amounts of the room temperature ionic liquid (RTIL) [P14,6,6,6]+[NTf2]-, in order to obtain a non-aqueous supporting electrolyte suitable for the electrodeposition process. The feasibility and performance of the analytical strategy were at first tested in standard solutions of Pb(II) in RTIL, produced by anodic dissolution of lead in the RTIL, as well as in olive oil samples mixed with 0.5 M RTIL and spiked with known amounts of Pb(II). The optimization of the electrochemical parameters was achieved by applying a D-Optimal Design, properly set up to optimise the efficiency of the deposition and re-oxidation steps, quantitative recovery and measurement time. Finally, the analytical procedure was applied to the determination of Pb content in some Italian EVOOs, without any need of performing mineralization pretreatments. Data obtained with the proposed procedure satisfactorily agree with those achieved by ICP-QMS analysis after microwave digestion, being differences between the two approaches within 10%, with the advantage of reducing to half the pretreatment time, operating at room temperature and avoiding the use of aggressive solvents

Electrochemosensor for Trace Analysis of Perfluorooctanesulfonate in Water Based on a Molecularly Imprinted Poly(<i>o</i>‑phenylenediamine) Polymer

This work is aimed at developing an electrochemical sensor for the sensitive and selective detection of trace levels of perfluorooctanesulfonate (PFOS) in water. Contamination of waters by perfluorinated alkyl substances (PFAS) is a problem of global concern due to their suspected toxicity and ability to bioaccumulate. PFOS is the perfluorinated compound of major concern, as it has the lowest suggested control concentrations. The sensor reported here is based on a gold electrode modified with a thin coating of a molecularly imprinted polymer (MIP), prepared by anodic electropolymerization of <i>o</i>-phenylenediamine (o-PD) in the presence of PFOS as the template. Activation of the sensor is achieved by template removal with suitable a solvent mixture. Voltammetry, a quartz crystal microbalance, scanning electron microscopy and elemental analysis were used to monitor the electropolymerization process, template removal, and binding of the analyte. Ferrocenecarboxylic acid (FcCOOH) has been exploited as an electrochemical probe able to generate analytically useful voltammetric signals by competing for the binding sites with PFOS, as the latter is not electroactive. The sensor has a low detection limit (0.04 nM), a satisfactory selectivity, and is reproducible and repeatable, giving analytical results in good agreement with those obtained by HPLC-MS/MS analyses

Seminal Cadmium Affects Human Sperm Motility Through the Stable Binding to Cell Membrane Authors

Environmental pollutants are claimed as major factors involved in the progressive decline of the fertility rate worldwide. Exposure to the heavy metal Cadmium (Cd) has been associated with reproductive toxicity due to its ionic mimicry. However, the possible direct accumulation of Cd in human sperm cells has been poorly investigated. In this study we aimed to clarify the possible direct effect of Cd exposure on sperm function, through the analysis of its cell accumulation. Semen sample from 30 male subjects residing in high environmental impact areas, and adhering to the “Exposoma e Plurifocalità nella Prevenzione Oncologica” campaign for testis cancer prevention, were compared with semen sample from 15 males residing in low exposure areas. Semen levels and cell Cd content were quantified by inductively-coupled plasma (ICP) spectroscopy. Cell Cd distribution was assessed by scanning electron microscopy coupled with energy dispersive spectroscopy (SEM-EDS). The impact of Cd on sperm function was evaluated by the in vitro exposure to the heavy metal, whilst possible scavenging approaches/agents were assessed. In addition to higher values of semen Cd, exposed subjects showed a reduction of total motile sperm fraction compared to not-exposed controls (59.6±13.6% vs 66.3±7.3%, P=0.037). Semen Cd levels were also significantly correlated with SEM-EDS signals of Cd detected on sperm head and neck (respectively =0.738, P&lt;0.001 and =0.465, P&lt;0.001). In vitro-2 hours exposure to 0.5 M Cd was associated with a significant reduction of sperm progressive motility. Scavenging approaches with either hypo-osmotic swelling or 10 M reduced glutathione were ineffective in blunting cell Cd and restoring motility. The reduction of exposure levels appears as the main approach to reduce the reproductive issues associated with Cd