Allelic heterogeneity and trade-off shape natural variation for response to soil micronutrient

Peer reviewedPublisher PD

Solubility of three natural compounds with insecticidal activity in supercritical carbon dioxide: Experimental measurements and predictive modeling with the GC-EoS

In this work, the solubility of thymoquinone, R-(+)-pulegone and 1-octen-3-ol in supercritical CO2 is determined in a range of conditions typical of supercritical fluid processes such as extraction, fractionation and impregnation. These compounds were selected based in their insecticidal activity which may enable to apply them as biopesticides. Solubility was measured using a semicontinuos method in the temperature range of 45–65 °C and pressure of 8–12 MPa, at a CO2 flowrate of 0.05–0.10 g/min, which was verified to be low enough to ensure saturation. Solubilities were predicted using the Group Contribution Equation of State (GC-EoS) and compared to the experimental results, with a good agreement. Consistency of the data was tested using the density-based Chrastil equation

Detection of Listeria monocytogenes in foods with a textile organic electrochemical transistor biosensor

Abstract: Foods contaminated by pathogens are responsible for foodborne diseases which have socioeconomic impacts. Many approaches have been extensively investigated to obtain specific and sensitive methods to detect pathogens in food, but they are often not easy to perform and require trained personnel. This work aims to propose a textile organic electrochemical transistor-based (OECT) biosensor to detect L. monocytogenes in food samples. The analyses were performed with culture-based methods, Listeria Precis™ method, PCR, and our textile OECT biosensor which used poly(3,4-ethylenedioxythiophene) (PEDOT):polystyrene sulfonate (PSS) (PEDOT:PSS) for doping the organic channel. Atomic force microscopy (AFM) was used to obtain topographic maps of the gold gate. The electrochemical activity on gate electrodes was measured and related to the concentration of DNA extracted from samples and hybridized to the specific capture probe immobilized onto the gold surface of the gate. This assay reached a limit of detection of 1.05 ng/μL, corresponding to 0.56 pM of L. monocytogenes ATCC 7644, and allowed the specific and rapid detection of L. monocytogenes in the analyzed samples. Keypoints: • Textile organic electrochemical transistors functionalized with a specific DNA probe • AFM topographic and surface potential maps of a functionalized gold gate surface • Comparison between the Listeria monocytogenes Precis™ method and an OECT biosenso

Effects of post-printing heat treatment on microstructure, corrosion and wet wear behavior of CoCrW alloy produced by L-PBF process

CoCr alloys are widely used as human implants because of both their superior corrosion resistance and superior mechanical properties (fatigue, wear resistance, etc.) respect to other metal alloys used in biomedical field. In particular, CoCrW alloys are used mainly to produce dental implants. In this study, the effects of thermal treatment on the corrosion resistance and wet wear resistance of CoCrW alloys produced via Laser-Powder Bed Fusion (L-PBF) were investigated, and the corrosion resistance and wet wear resistance of the L-PBF specimens were compared with those of the specimens obtained after forging. The heat treatment involved the solubilization of the alloy at 1150 °C in an Ar-saturated atmosphere, followed by furnace cooling. A detailed microstructural characterization of the L-PBF specimens was carried out using a light microscope and a scanning electron microscope in both the horizontal and vertical growth directions. Scanning Kelvin probe measurements were performed on the heat-treated specimens obtained by three-dimensional printing and forging. The void contents of the specimens were evaluated using the Archimedes’ method and image analysis. Vickers (HV2) hardness measurements were performed to evaluate the mechanical properties of the specimens. The corrosion properties of the specimens were evaluated by carrying out potentiodynamic tests in two different corrosive media (aqueous solution (9 g/L NaCl) at pH = 2 and 7). The corroded areas of the specimens were then examined using scanning electron microscopy (SEM). Finally, tribological tests were performed using the pin (Ti counter material)-on-flat configuration under dry and wet conditions, using the same corrosive environments as those used in the potentiodynamic tests and two different stroke lengths. The worn samples were characterized using SEM to investigate their wear mechanisms, and a stylus profilometer was used to determine the wear rates of the materials. The experimental results showed that the additively manufactured CoCrW L-PBF alloy had higher corrosion resistance than the wrought material. In addition, the additively manufactured material showed better dry and wet wear performances than the wrought material. Nevertheless, the heat treatment did not affect the properties evaluated in this study

The Multi-allelic Genetic Architecture of a Variance-Heterogeneity Locus for Molybdenum Concentration in Leaves Acts as a Source of Unexplained Additive Genetic Variance

Funding: We acknowledge support from the US National Institutes of Health (http://www.nih.gov/) (grant 2R01GM078536 to DES), European Commission (http://ec.europa.eu/index_en.htm) (grant PCIG9-GA-2011-291798 to DES) and UK Biotechnology and Biological Sciences Research Council (http://www.bbsrc.ac.uk/) (grants BB/L000113/1 to DES). The funders had no role in study design, data collection and analysis, decision to publish, or preparation of the manuscript.Peer reviewedPublisher PD

Reinstatement of contextual conditioned anxiety in virtual reality and the effects of transcutaneous vagus nerve stimulation in humans

Since exposure therapy for anxiety disorders incorporates extinction of contextual anxiety, relapses may be due to reinstatement processes. Animal research demonstrated more stable extinction memory and less anxiety relapse due to vagus nerve stimulation (VNS). We report a valid human three-day context conditioning, extinction and return of anxiety protocol, which we used to examine efects of transcutaneous VNS (tVNS). Seventy-fve healthy participants received electric stimuli (unconditioned stimuli, US) during acquisition (Day1) when guided through one virtual ofce (anxiety context, CTX+) but never in another (safety context, CTX−). During extinction (Day2), participants received tVNS, sham, or no stimulation and revisited both contexts without US delivery. On Day3, participants received three USs for reinstatement followed by a test phase. Successful acquisition, i.e. startle potentiation, lower valence, higher arousal, anxiety and contingency ratings in CTX+ versus CTX−, the disappearance of these efects during extinction, and successful reinstatement indicate validity of this paradigm. Interestingly, we found generalized reinstatement in startle responses and diferential reinstatement in valence ratings. Altogether, our protocol serves as valid conditioning paradigm. Reinstatement efects indicate diferent anxiety networks underlying physiological versus verbal responses. However, tVNS did neither afect extinction nor reinstatement, which asks for validation and improvement of the stimulation protocol

Effect of Thermal Treatment on Corrosion Behavior of AISI 316L Stainless Steel Manufactured by Laser Powder Bed Fusion

The effect of post-processing heat treatment on the corrosion behavior of AISI 316L stainless steel manufactured by laser powder bed fusion (L-PBF) is investigated in this work. Produced stainless steel was heat treated in a broad temperature range (from 200 °C to 1100 °C) in order to evaluate the electrochemical behavior and morphology of corrosion. The electrochemical behavior was investigated by potentiodynamic and galvanostatic polarization in a neutral and acidic (pH 1.8) 3.5% NaCl solution. The microstructure modification after heat treatment and the morphology of attack of corroded samples were evaluated by optical and scanning electron microscopy. The fine cellular/columnar microstructure typically observed for additive-manufactured stainless steel evolves into a fine equiaxed austenitic structure after thermal treatment at high temperatures (above 800 °C). The post-processing thermal treatment does not negatively affect the electrochemical behavior of additive-manufactured stainless steel even after prolonged heat treatment at 1100 °C for 8 h and 24 h. This indicates that the excellent barrier properties of the native oxide film are retained after heat treatment

Metabolomic profile of amniotic fluid to evaluate lung maturity: the diaphragmatic hernia lamb model

Background: Tracheal occlusion (TO) stimulates lung growth in fetuses affected with congenital diaphragmatic hernia (CDH) although the processes involved in lung maturation still remain unknown. The objective of this study was to evaluate the metabolomic profile of amniotic fluid (AF) following TO in fetal lamb model in order to obtain an indirect view of mechanisms involved in pulmonary reversal hypoplasia and biochemical maturity in response to fetal TO. Methods: Liquid Chromatography Mass Spectrometry was performed on lamb AF samples at: age I (70 days' gestation); age II (102 days' gestation); age III (136 days' gestation). CDH was induced at age I and TO at age II. Results: Betaine, choline, creatinine were found significantly increased during gestation in the control group. The CDH group showed choline (p =0.007) and creatinine (p =0.004) decreases during pregnancy. In the TO group choline and creatinine profiles were restored. Conclusions: Alveolar tissue and fetal global growth ameliorated after TO. Metabolomics provided usefu information on biochemical details during lung maturation. Metabolomic profiling would help to identify the best time to perform TO, in order to increase survival of CDH affected patients

From music to mathematics and backwards: introducing algebra, topology and category theory into computational musicology

International audienceDespite a long historical relationship between mathematics and music, the interest of mathematicians is a recent phenomenon. In contrast to statistical methods and signal-based approaches currently employed in MIR (Music Information Research), the research project described in this paper stresses the necessity of introducing a structural multidisciplinary approach into computational musicology making use of advanced mathematics. It is based on the interplay between three main mathematical disciplines: algebra, topology and category theory. It therefore opens promising perspectives on important prevailing challenges, such as the automatic classification of musical styles or the solution of open mathematical conjectures, asking for new collaborations between mathematicians, computer scientists, musicologists, and composers. Music can in fact occupy a strategic place in the development of mathematics since music-theoretical constructions can be used to solve open mathematical problems. The SMIR project also differs from traditional applications of mathematics to music in aiming to build bridges between different musical genres, ranging from contemporary art music to popular music, including rock, pop, jazz and chanson. Beyond its academic ambition, the project carries an important societal dimension stressing the cultural component of 'mathemusical' research, that naturally resonates with the underlying philosophy of the “Imagine Maths”conference series. The article describes for a general public some of the most promising interdisciplinary research lines of this project

Effect of powder recycling on inclusion content and distribution in AISI 316L produced by L-PBF technique

AISI 316 L stainless steel is widely used as material to produce components by means of additive manufacturing. To increase the circular economy, the powders are collected and re-used after the printing process, thus the effect of powder recycling on microstructure and properties of printed components is of the utmost importance. This work focused the attention on non-metallic inclusions by examining virgin and recycled powders, and products printed by using both types of powders in a laser powder bed fusion (L-PBF) process. Recycled powders exhibit an irregular shape due to fragmentation, spatters and satellites and, compared to the virgin ones, have a higher gas (O, H and C) content. Both powders contain non-metallic inclusions with a larger quantity in the recycled ones. The printed samples have a similar microstructure, however those produced by using recycled powders exhibit voids of larger size and a little greater amount of inclusions. XRD and EDS examinations of inclusions extracted from the metallic matrix showed that they consist of a mix of amorphous and crystalline silica. Large part of these particles are already present in virgin powders and only a minor part forms during repeated printing operations. Accordingly, the quality of virgin powders is the factor that mainly affects the inclusion content of printed products indicating that the powder production process is the most critical stage of the whole manufacturing process