Numerical simulation of deformation behavior of aluminum alloy sheets under processing by groove pressing method

The results of theoretical estimation of capabilities of the material structure modification of 1560 aluminum alloy sheets under processing by severe plastic deformation are presented in this paper. Severe plastic deformation of flat specimens is effected by the constrained groove pressing method in original dies with trapezoidal teeth. The numerical simulation results of the sheet specimen treatment process by severe plastic deformation were used for dies designing. The stress-strain state of flat aluminum alloy specimens and the steel dies at high processing temperature, support reaction force during pressing and the degrees of plastic strain accumulation at the optimum mode of pressing were estimated. The main numerical result is the value of accumulated plastic strain in the specimen per one pressing cycle which is about 1.14. Large degrees of strain are the reasons of grain structure and material texture changes, which leads to inevitable change of its physical-mechanical properties. Increasing the number of pressing cycles leads to proportional increase of the degree of accumulated plastic strain

Mechanical properties of weld joints of high-strength steel under dynamic loading

The paper represents a computational model for predicting the mechanical behavior of welded joints in steel constructions under dynamic load, taking into account the change in the properties of the steel in the welding zone. Plastic deformation localization and formation of cracks in welded joints subjected to tensile loading have been studied numerically. Numerical modeling confirms that the model proposed in the work can predict the strength and mechanical behavior of welded joints in steel constructions in a wide range of strain rates, taking into account the phase and granular structure in the weld area. The results confirm that residual stresses of ~ 100–150 MPa do not significantly affect the formation of the fracture zone in arc welded joints of 09G2S steel subjected to dynamic loading. Fracture of considered welded joints exhibits ductile behavior at initial temperature of 295K and high strain rates. The results have shown that mesoscopic cracks nucleate in the heat-affected zone at effective strains above 12%

Evaluation of the possibility of obtaining welded joints of plates from Al-Mg-Mn aluminum alloys, strengthened by the introduction of TiB2 particles

In the work, the possibility of obtaining strong welded joints of aluminum alloys modified with particles is demonstrated. For research, strengthened aluminum alloys of the Al-Mg-Mn system with the introduction of TiB2 particles were obtained. TiB2 particles in specially prepared Al-TiB master alloys obtained by self-propagating high-temperature synthesis were introduced ex situ into the melt according to an original technique using ultrasonic treatment. Plates from the studied cast alloys were butt-welded by one-sided welded joints of various depths. To obtain welded joints, the method of electron beam welding was used. Mechanical properties of the studied alloys and their welded joints under tension were studied. It was shown that the introduction of particles resulted in a change in the internal structure of the alloys, characterized by the formation of compact dendritic structures and a decrease in the average grain size from 155 to 95 µm. The change in the internal structure due to the introduction of particles led to an increase in the tensile strength of the obtained alloys from 163 to 204 MPa. It was found that the obtained joints have sufficient relative strength values. Relative strength values reach 0.9 of the nominal strength of materials already at the ratio of the welded joint depth to the thickness of the welded plates, equal to 0.6 for the initial alloy and in the range of 0.67–0.8 for strengthened alloys

Employing culturally responsive pedagogy to foster literacy learning in schools

 In recent years it has become increasingly obvious that, to enable students in schools from an increasingly diverse range of cultural backgrounds to acquire literacy to a standard that will support them to achieve academically, it is important to adopt pedagogy that is responsive to, and respectful of, them as culturally situated. What largely has been omitted from the literature, however, is discussion of a relevant model of learning to underpin this approach. For this reason this paper adopts a socio-cultural lens (Vygotsky, 1978) through which to view such pedagogy and refers to a number of seminal texts to justify of its relevance. Use of this lens is seen as having a particular rationale. It forces a focus on the agency of the teacher as a mediator of learning who needs to acknowledge the learner’s cultural situatedness (Kozulin, 2003) if school literacy learning for all students is to be as successful as it might be. It also focuses attention on the predominant value systems and social practices that characterize the school settings in which students’ literacy learning is acquired. The paper discusses implications for policy and practice at whole-school, classroom and individual student levels of culturally-responsive pedagogy that is based on a socio-cultural model of learning. In doing so it draws on illustrations from the work of a number of researchers, including that of the author

Calibration methodology of program package for optic measuring of strain and crack resistance determination of compact tension specimens

In the work, the problem of eccentric tension of a compact specimen with a crack was solved by numerical methods. It was proposed to use the results of numerical modeling for setting up and testing the original software package for measuring the deformation of materials by optical methods. The values of the fracture parameters obtained by software coincide with the experimental and numerical results. The proposed testing methodology made it possible to avoid problems with determining the error in the quality of calculation of the optical flow during verification. The dependences of the change of the values of stress intensity factor and J-integral on the applied tensile loading are determined for compact tension specimen with a crack from aluminum alloy D16

On the Tensile Strength of Spark Plasma Sintered AlMgB14 Ceramics

In this work, the structure, phase composition, hardness and tensile strength of the AlMgB14-based material obtained by spark plasma sintering (SPS) were investigated. According to the XRD results, the spark plasma sintered material contains 94 wt% AlMgB14 phase and 6 wt% spinel MgAl2O4. Analysis of the SEM images showed that the obtained AlMgB14 sample has a dense structure; the relative density of the sample is 98.6%. The average microhardness of the spark plasma sintered (SPSed) sample is 29 ± 0.88 GPa. According to the results of the Brazilian test, the tensile strength of AlMgB14 is 56 MPa. The fracture is characterized by a single straight tensile crack that divides the sample along the compression line into two halves. The type of fracture in the AlMgB14 sample can be characterized as a cleavage fracture due to crack growth occurring in accordance with the transcrystalline fracture. The tensile strength of the obtained material is in good agreement with the tensile strength of boride and oxide ceramics studied in other works