53 research outputs found
Visualization of paper structure by optical coherence tomography: Monte Carlo simulations and experimental study
This paper analyzes the capability of an optical coherence tomography (OCT) setup to visualize paper structure by comparing experimental and Monte Carlo (MC) simulated OCT images. In the experiments, we used an OCT setup at 910 nm with the coherence length of an SLD source of 7.5 mum. Several different refractive index matching agents were applied to paper samples to enhance the visualization of their inner structure. The obtained OCT images show improved contrast in inner structure and enhanced visualization depth. A set of corresponding simulations were then performed using a previously developed MC code. A multilayer paper sheet model with non-planar fiber-air interfaces was developed to characterize the paper samples. MC simulations were carried out to study the effect of the setup parameters on the obtained OCT images. A comparison with the experimental data shows that the developed model provides a satisfactory correspondence between simulated and experimental images
Quantum Confinement-Tunable Ultrafast Charge Transfer at the PbS Quantum Dot and Phenyl-C_(61)-butyric Acid Methyl Ester Interface
Quantum dot (QD) solar cells have emerged as promising low-cost alternatives to existing photovoltaic technologies. Here, we investigate charge transfer and separation at PbS QDs and phenyl-C_(61)-butyric acid methyl ester (PCBM) interfaces using a combination of femtosecond broadband transient absorption (TA) spectroscopy and steady-state photoluminescence quenching measurements. We analyzed ultrafast electron injection and charge separation at PbS QD/PCBM interfaces for four different QD sizes and as a function of PCBM concentration. The results reveal that the energy band alignment, tuned by the quantum size effect, is the key element for efficient electron injection and charge separation processes. More specifically, the steady-state and time-resolved data demonstrate that only small-sized PbS QDs with a bandgap larger than 1 eV can transfer electrons to PCBM upon light absorption. We show that these trends result from the formation of a type-II interface band alignment, as a consequence of the size distribution of the QDs. Transient absorption data indicate that electron injection from photoexcited PbS QDs to PCBM occurs within our temporal resolution of 120 fs for QDs with bandgaps that achieve type-II alignment, while virtually all signals observed in smaller bandgap QD samples result from large bandgap outliers in the size distribution. Taken together, our results clearly demonstrate that charge transfer rates at QD interfaces can be tuned by several orders of magnitude by engineering the QD size distribution. The work presented here will advance both the design and the understanding of QD interfaces for solar energy conversion
Real-Space Mapping of Surface Trap States in CIGSe Nanocrystals Using 4D Electron Microscopy
Low trap-state density and long carrier diffusion in organolead trihalide perovskite single crystals
The fundamental properties and ultimate performance limits of organolead trihalide MAPbX3 (MA = CH3NH3 +; X = Br– or I–) perovskites remain obscured by extensive disorder in polycrystalline MAPbX3 films. We report an antisolvent vapor-assisted crystallization approach that enables us to create sizable crack-free MAPbX3 single crystals with volumes exceeding 100 cubic millimeters. These large single crystals enabled a detailed characterization of their optical and charge transport characteristics. We observed exceptionally low trap-state densities on the order of 109 to 1010 per cubic centimeter in MAPbX3 single crystals (comparable to the best photovoltaic-quality silicon) and charge carrier diffusion lengths exceeding 10 micrometers. These results were validated with density functional theory calculations
Intrinsic efficiency limits in low-bandgap non-fullerene acceptor organic solar cells
In bulk heterojunction (BHJ) organic solar cells (OSCs) both the electron affinity (EA) and ionization energy (IE) offsets at the donor–acceptor interface should equally control exciton dissociation. Here, we demonstrate that in low-bandgap non-fullerene acceptor (NFA) BHJs ultrafast donor-to-acceptor energy transfer precedes hole transfer from the acceptor to the donor and thus renders the EA offset virtually unimportant. Moreover, sizeable bulk IE offsets of about 0.5 eV are needed for efficient charge transfer and high internal quantum efficiencies, since energy level bending at the donor–NFA interface caused by the acceptors’ quadrupole moments prevents efficient exciton-to-charge-transfer state conversion at low IE offsets. The same bending, however, is the origin of the barrier-less charge transfer state to free charge conversion. Our results provide a comprehensive picture of the photophysics of NFA-based blends, and show that sizeable bulk IE offsets are essential to design efficient BHJ OSCs based on low-bandgap NFAs
Ultrahigh Carrier Mobility Achieved in Photoresponsive Hybrid Perovskite Films via Coupling with Single-Walled Carbon Nanotubes
Organolead trihalide perovskites have drawn substantial interest for photovoltaic and optoelectronic applications due to their remarkable physical properties and low processing cost. However, perovskite thin films suffer from low carrier mobility as a result of their structural imperfections such as grain boundaries and pinholes, limiting their device performance and application potential. Here we demonstrate a simple and straightforward synthetic strategy based on coupling perovskite films with embedded single-walled carbon nanotubes. We are able to significantly enhance the hole and electron mobilities of the perovskite film to record-high values of 595.3 and 108.7 cm2 V−1 s−1, respectively. Such a synergistic effect can be harnessed to construct ambipolar phototransistors with an ultrahigh detectivity of 3.7 × 1014 Jones and a responsivity of 1 × 104 A W−1, on a par with the best devices available to date. The perovskite/carbon nanotube hybrids should provide a platform that is highly desirable for fields as diverse as optoelectronics, solar energy conversion, and molecular sensing
Low coherence interferometry and optical coherence tomography in paper measurements
Abstract
This thesis describes the application of Low Coherence Interferometry (LCI) and Optical Coherence Tomography (OCT) in paper measurements. The developed measurement system is a combination of a profilometer and a tomographic imaging device, which makes the construction versatile and applicable in several paper measurement applications. The developed system was first used to measure the surface structure of paper.
Different grades of paper were selected to provide maximum variation in surface structure. The results show that the developed system is capable of measuring grades of paper from rough base paper to highly coated photo printing paper.
To evaluate the developed system in surface characterization, the roughness parameters of five laboratory-made paper samples measured with the developed system and with a commercial optical profilometer were compared. A linear correlation was found with roughness parameters Ra and Rq.
Next, the surface quality of paper was evaluated using LCI, a Diffractive Optical Element Based Glossmeter (DOG), and a commercial glossmeter. The results show linear correlation between Ra and gloss measured with the commercial glossmeter. The roughness Ra and averaged gloss measured with the DOG didn't give such a correlation, but a combination of these techniques provided local properties of gloss and surface structure, which can be used to evaluate the local surface properties of paper.
In the next study, determination of the filler content of paper using OCT is discussed. The measurement results show clear correspondence of the slope of the averaged logarithmic fringe signal envelope and the filler content.
The last studies focus on 2D and 3D imaging of paper using OCT and begin with imaging of a self-made wood fiber network. The visibility of the fibers was clear. Next, several refractive index matcing agents are studied by means of light transmittance and OCT measurements to find the best possible agent for enhancing the imaging depth of OCT in paper. Benzyl alcohol was found to have the best possible combination of optical, evaporation, and sorption characteristics, and it is applied in 2D and 3D visualizations of copy paper
- …