An enhanced surface passivation effect in InGaN/GaN disk-in-nanowire light emitting diodes for mitigating Shockley-Read-Hall recombination

We present a detailed study of the effects of dangling bond passivation and the comparison of different sulfide passivation processes on the properties of InGaN/GaN quantum-disk (Qdisk)-in-nanowire based light emitting diodes (NW-LEDs). Our results demonstrated the first organic sulfide passivation process for nitride nanowires (NWs). The results from Raman spectroscopy, photoluminescence (PL) measurements, and X-ray photoelectron spectroscopy (XPS) showed that octadecylthiol (ODT) effectively passivated the surface states, and altered the surface dynamic charge, and thereby recovered the band-edge emission. The effectiveness of the process with passivation duration was also studied. Moreover, we also compared the electro-optical performance of NW-LEDs emitting at green wavelength before and after ODT passivation. We have shown that the Shockley–Read–Hall (SRH) non-radiative recombination of NW-LEDs can be greatly reduced after passivation by ODT, which led to a much faster increasing trend of quantum efficiency and higher peak efficiency. Our results highlighted the possibility of employing this technique to further design and produce high performance NW-LEDs and NW-lasers

High-Selectivity Growth of GaN Nanorod Arrays by Liquid-Target Magnetron Sputter Epitaxy

Selective-area grown, catalyst-free GaN nanorod (NR) arrays grown on Si substrates have been realized using liquid-target reactive magnetron sputter epitaxy (MSE). Focused ion beam lithography (FIBL) was applied to pattern Si substrates with TiN(x)masks. A liquid Ga target was sputtered in a mixture gas of Ar and N-2, ranging the N(2)partial pressure (P-N) ratio from 100% to 50%. The growth of NRs shows a strong correlation withP(N)on the selectivity, coalescence, and growth rate of NRs in both radial and axial directions. The growth rate of NRs formed inside the nanoholes increases monotonically withP(N). TheP(N)ratio between 80% and 90% was found to render both a high growth rate and high selectivity. When theP(N)ratio was below 80%, multiple NRs were formed in the nanoholes. For aP(N)ratio higher than 90%, parasitic NRs were grown on the mask. An observed dependence of growth behavior upon theP(N)ratio is attributed to a change in the effective Ga/N ratio on the substrate surface, as an effect of impinging reactive species, surface diffusivity, and residence time of adatoms. The mechanism of NR growth control was further investigated by studying the effect of nanoholes array pitch and growth temperature. The surface diffusion and the direct impingement of adatoms were found to be the dominant factors affecting the lateral and axial growth rates of NR, respectively, which were well elucidated by the collection area model.Funding Agencies|Energimyndigheten [46658-1]; VetenskapsradetSwedish Research Council [2018-04198]; Stiftelsen Olle Engkvist ByggmastareSwedish Research Council [197-0210]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University [SFO-Mat-LiU 2009-00971]; Energimyndigheten</p

Direct Growth of III-Nitride Nanowire-Based Yellow Light-Emitting Diode on Amorphous Quartz Using Thin Ti Interlayer

Abstract Consumer electronics have increasingly relied on ultra-thin glass screen due to its transparency, scalability, and cost. In particular, display technology relies on integrating light-emitting diodes with display panel as a source for backlighting. In this study, we undertook the challenge of integrating light emitters onto amorphous quartz by demonstrating the direct growth and fabrication of a III-nitride nanowire-based light-emitting diode. The proof-of-concept device exhibits a low turn-on voltage of 2.6 V, on an amorphous quartz substrate. We achieved ~ 40% transparency across the visible wavelength while maintaining electrical conductivity by employing a TiN/Ti interlayer on quartz as a translucent conducting layer. The nanowire-on-quartz LED emits a broad linewidth spectrum of light centered at true yellow color (~ 590 nm), an important wavelength bridging the green-gap in solid-state lighting technology, with significantly less strain and dislocations compared to conventional planar quantum well nitride structures. Our endeavor highlighted the feasibility of fabricating III-nitride optoelectronic device on a scalable amorphous substrate through facile growth and fabrication steps. For practical demonstration, we demonstrated tunable correlated color temperature white light, leveraging on the broadly tunable nanowire spectral characteristics across red-amber-yellow color regime

Direct Growth of Single Crystalline GaN Nanowires on Indium Tin Oxide-Coated Silica

Abstract In this work, we demonstrated the direct growth of GaN nanowires on indium tin oxide (ITO)-coated fused silica substrate. The nanowires were grown catalyst-free using plasma-assisted molecular beam epitaxy (PA-MBE). The effect of growth condition on the morphology and quality of the nanowires is systematically investigated. Structural characterization indicates that the nanowires grow in the (0001) direction directly on top of the ITO layer perpendicular to the substrate plane. Optical characterization of the nanowires shows that yellow luminescence is absent from the nanowire’s photoluminescence response, attributed to the low number of defects. Conductive atomic force microscopy (C-AFM) measurement on n-doped GaN nanowires shows good conductivity for individual nanowires, which confirms the potential of using this platform for novel device applications. By using a relatively low-temperature growth process, we were able to successfully grow high-quality single-crystal GaN material without the degradation of the underlying ITO layer

Facile Formation of High-Quality InGaN/GaN Quantum-Disks-in-Nanowires on Bulk-Metal Substrates for High-Power Light-Emitters

High-quality nitride materials grown on scalable and low-cost metallic substrates are considerably attractive for high-power light-emitters. We demonstrate here, for the first time, the high-power red (705 nm) InGaN/GaN quantum-disks (Qdisks)-in-nanowire light-emitting diodes (LEDs) self-assembled directly on metal-substrates. The LEDs exhibited a low turn-on voltage of ∼2 V without efficiency droop up to injection current of 500 mA (1.6 kA/cm²) at ∼5 V. This is achieved through the direct growth and optimization of high-quality nanowires on titanium (Ti) coated bulk polycrystalline-molybdenum (Mo) substrates. We performed extensive studies on the growth mechanisms, obtained high-crystal-quality nanowires, and confirmed the epitaxial relationship between the cubic titanium nitride (TiN) transition layer and the hexagonal nanowires. The growth of nanowires on all-metal stack of TiN/Ti/Mo enables simultaneous implementation of n-metal contact, reflector, and heat sink, which greatly simplifies the fabrication process of high-power light-emitters. Our work ushers in a practical platform for high-power nanowires light-emitters, providing versatile solutions for multiple cross-disciplinary applications that are greatly enhanced by leveraging on the chemical stability of nitride materials, large specific surface of nanowires, chemical lift-off ready layer structures, and reusable Mo substrates

Facile Formation of High-Quality InGaN/GaN Quantum-Disks-in-Nanowires on Bulk-Metal Substrates for High-Power Light-Emitters

High-quality nitride materials grown on scalable and low-cost metallic substrates are considerably attractive for high-power light-emitters. We demonstrate here, for the first time, the high-power red (705 nm) InGaN/GaN quantum-disks (Qdisks)-in-nanowire light-emitting diodes (LEDs) self-assembled directly on metal-substrates. The LEDs exhibited a low turn-on voltage of ∼2 V without efficiency droop up to injection current of 500 mA (1.6 kA/cm²) at ∼5 V. This is achieved through the direct growth and optimization of high-quality nanowires on titanium (Ti) coated bulk polycrystalline-molybdenum (Mo) substrates. We performed extensive studies on the growth mechanisms, obtained high-crystal-quality nanowires, and confirmed the epitaxial relationship between the cubic titanium nitride (TiN) transition layer and the hexagonal nanowires. The growth of nanowires on all-metal stack of TiN/Ti/Mo enables simultaneous implementation of n-metal contact, reflector, and heat sink, which greatly simplifies the fabrication process of high-power light-emitters. Our work ushers in a practical platform for high-power nanowires light-emitters, providing versatile solutions for multiple cross-disciplinary applications that are greatly enhanced by leveraging on the chemical stability of nitride materials, large specific surface of nanowires, chemical lift-off ready layer structures, and reusable Mo substrates

Bandgap measurements and the peculiar splitting of E2H phonon modes of InxAl1-xN nanowires grown by plasma assisted molecular beam epitaxy

INTERLOCUTORY APPEAL FROM THE FIFTH JUDICIAL DISTRICT COURT IN AND FOR WASHINGTON COUNTY, STATE OF UTAH HONORABLE J. PHILIP EVES, PRESIDIN