87 research outputs found
Sublattice identification in noncontact atomic force microscopy of the NaCl(001) surface
We compare the three-dimensional force field obtained from frequency-distance measurements above the NaCl(001) surface to atomistic calculations using various tip models. In the experiments, long-range forces cause a total attractive force even on the similarly charged site. Taking force differences between two sites minimizes the influence of such long-range forces. The magnitude of the measured force differences are by a factor of 6.5â10 smaller than the calculated forces. This is an indication that for the particular tip used in this experiment several atoms of the tip interact with the surface atoms at close tip-sample distances. The interaction of these additional atoms with the surface is small at the imaging distance, because symmetric images are obtained. The force distance characteristics resemble those of a negative tip apex ion which could be explained, e.g., by a neutral Si tip.Peer reviewe
Ageing of a Microscopic Sliding Gold Contact at Low Temperatures
Nanometer-scale friction measurements on a Au(111) surface have been performed at temperatures between 30 and 300 K by means of atomic force microscopy. Stable stick slip with atomic periodicity is observed at all temperatures, showing only weak dependence on temperature between 300 and 170 K. Below 170 K, friction increases with time and a distortion of the stick-slip characteristic is observed. Low friction and periodic stick slip can be reestablished by pulling the tip out of contact and subsequently restoring the contact. A comparison with molecular dynamics simulations indicates that plastic deformation within a growing gold junction leads to the observed frictional behavior at low temperatures. The regular stick slip with atomic periodicity observed at room temperature is the result of a dynamic equilibrium shape of the contact, as microscopic wear damage is observed to heal in the sliding contact
Temperature dependence of the energy dissipation in dynamic force microscopy
The dissipation of energy in dynamic force microscopy is usually described in
terms of an adhesion hysteresis mechanism. This mechanism should become less
efficient with increasing temperature. To verify this prediction we have
measured topography and dissipation data with dynamic force microscopy in the
temperature range from 100 K up to 300 K. We used
3,4,9,10-perylenetetracarboxylic-dianhydride (PTCDA) grown on KBr(001), both
materials exhibiting a strong dissipation signal at large frequency shifts. At
room temperature, the energy dissipated into the sample (or tip) is 1.9
eV/cycle for PTCDA and 2.7 eV/cycle for KBr, respectively, and is in good
agreement with an adhesion hysteresis mechanism. The energy dissipation over
the PTCDA surface decreases with increasing temperature yielding a negative
temperature coefficient. For the KBr substrate, we find the opposite behaviour:
an increase of dissipated energy with increasing temperature. While the
negative temperature coefficient in case of PTCDA agrees rather well with the
adhesion hysteresis model, the positive slope found for KBr points to a
hitherto unknown dissipation mechanism
Probing the shape of atoms in real space
The structure of single atoms in real space is investigated by scanning
tunneling microscopy. Very high resolution is possible by a dramatic reduction
of the tip-sample distance. The instabilities which are normally encountered
when using small tip-sample distances are avoided by oscillating the tip of the
scanning tunneling microscope vertically with respect to the sample. The
surface atoms of Si(111)-(7 x 7) with their well-known electronic configuration
are used to image individual samarium, cobalt, iron and silicon atoms. The
resulting images resemble the charge density corresponding to 4f, 3d and 3p
atomic orbitals.Comment: Submitted to Phys. Rev. B, 17 pages, 7 figure
Calibration of quartz tuning fork spring constants for non-contact atomic force microscopy: Direct mechanical measurements and simulations
Quartz tuning forks are being increasingly employed as sensors in non-contact atomic force microscopy especially in the âqPlusâ design. In this study a new and easily applicable setup has been used to determine the static spring constant at several positions along the prong of the tuning fork. The results show a significant deviation from values calculated with the beam formula. In order to understand this discrepancy the complete sensor set-up has been digitally rebuilt and analyzed by using finite element method simulations. These simulations provide a detailed view of the strain/stress distribution inside the tuning fork. The simulations show quantitative agreement with the beam formula if the beam origin is shifted to the position of zero stress onset inside the tuning fork base and torsional effects are also included. We further found significant discrepancies between experimental calibration values and predictions from the shifted beam formula, which are related to a large variance in tip misalignment during the tuning fork assembling process
Recent highlights in nanoscale and mesoscale friction
Friction is the oldest branch of non-equilibrium condensed matter physics and, at the same time, the least established at the fundamental level. A full understanding and control of friction is increasingly recognized to involve all relevant size and time scales. We review here some recent advances on the research focusing of nano- and mesoscale tribology phenomena. These advances are currently pursued in a multifaceted approach starting from the fundamental atomic-scale friction and mechanical control of specific single-asperity combinations, e.g., nanoclusters on layered materials, then scaling up to the meso/microscale of extended, occasionally lubricated, interfaces and driven trapped optical systems, and eventually up to the macroscale. Currently, this "hot" research field is leading to new technological advances in the area of engineering and materials science
Surface-controlled reversal of the selectivity of halogen bonds
Intermolecular halogen bonds are ideally suited for designing new molecular assemblies because of their strong directionality and the possibility of tuning the interactions by using different types of halogens or molecular moieties. Due to these unique properties of the halogen bonds, numerous areas of application have recently been identified and are still emerging. Here, we present an approach for controlling the 2D self-assembly process of organic molecules by adsorption to reactive vs. inert metal surfaces. Therewith, the order of halogen bond strengths that is known from gas phase or liquids can be reversed. Our approach relies on adjusting the molecular charge distribution, i.e., the Ï-hole, by molecule-substrate interactions. The polarizability of the halogen and the reactiveness of the metal substrate are serving as control parameters. Our results establish the surface as a control knob for tuning molecular assemblies by reversing the selectivity of bonding sites, which is interesting for future applications
- âŠ