4,444 research outputs found
Recommended from our members
Normal Rack Grid Generation Method for Screw Machines with Large Helix Angles
Improving the efficiency of the screw machine is highly significant for industry. Numerical simulation is an important tool in developing these machines. The 3D computational fluid dynamic simulation can give a valuable insight into the flow parameters of screw machines. However, it is currently difficult to generate high quality computational grids required for screw rotors with large helix angle. This is mainly due to the excessively high cell skewness of the rotors with large helix angel, which would introduce errors in numerical simulation. This paper presents a novel grid generation algorithm used for the screw rotors with large helix angel. This method is based on the principles developed for the grid generation in transverse cross-section. Such mesh is generated by SCORGTM using normal rack grid generation method which means numerical meshes are generated in a plane normal to the pitch helix line. The mesh lines are then parallel to the helix line and thus an orthogonal mesh will be produced. The main flow and leakage flow directions are orthogonal to the mesh, potentially reducing numerical diffusion. This developed algorithm could also be employed for single screw machines
Recommended from our members
Experimental Investigation of the Transient Flow in Roots Blower
Rotary positive displacement machines are common method to pump flow in various process industries. Their performance highly depends on the operational clearances. It is widely believed that computational fluid dynamics (CFD) can help understanding and reducing internal leakage flows. However, Developments of grid generating tools for use of CFD in rotary positive displacement machines have not yet been fully validated. Thereby arising a need to validate these models that help in better understanding of the leakage flows. Roots blower is a good representative of positive displacement machines and as such is convenient for optical access to analyse flows in in such machines. This paper describes the setup of the experimental test rig with the optical Roots blower in the Centre for Compressor Technology at City, University of London and the first results obtained using three different flow visualization methods. These are namely i) the high-speed camera (HC), ii) the continuous time resolved PIV (CPIV) and iii) the instantaneous PIV obtained with double pulse PIV laser and double shutter camera (IPIV). Test results from these three tests are compared and discussed in the paper. The CPIV test shows the movement of the vortex and the general shape of the flow field clearly but is not sufficient to calculate velocity vectors of high-velocity particles due to the limitation of the laser and camera. The IPIV test can produce quantitative velocity vector images of the internal flow but needs improvement to look into the leakage flow. The work described in this paper is a part of the large project set to evaluate characteristics of the internal flow in rotary positive displacement machines and to characterize leakage flows. The objective is to enable further improvements in 3D CFD analysis of leakage flows in rotary positive displacement machines and ultimately lead to the improvement in the performance of rotary positive displacement machines
A software approach to defeating side channels in last-level caches
We present a software approach to mitigate access-driven side-channel attacks
that leverage last-level caches (LLCs) shared across cores to leak information
between security domains (e.g., tenants in a cloud). Our approach dynamically
manages physical memory pages shared between security domains to disable
sharing of LLC lines, thus preventing "Flush-Reload" side channels via LLCs. It
also manages cacheability of memory pages to thwart cross-tenant "Prime-Probe"
attacks in LLCs. We have implemented our approach as a memory management
subsystem called CacheBar within the Linux kernel to intervene on such side
channels across container boundaries, as containers are a common method for
enforcing tenant isolation in Platform-as-a-Service (PaaS) clouds. Through
formal verification, principled analysis, and empirical evaluation, we show
that CacheBar achieves strong security with small performance overheads for
PaaS workloads
A search for rotating radio transients and fast radio bursts in the Parkes high-latitude pulsar survey
Discoveries of rotating radio transients and fast radio bursts (FRBs) in
pulsar surveys suggest that more of such transient sources await discovery in
archival data sets. Here we report on a single-pulse search for dispersed radio
bursts over a wide range of Galactic latitudes (|b| < ) in data
previously searched for periodic sources by Burgay et al. We re-detected 20 of
the 42 pulsars reported by Burgay et al. and one rotating radio transient
reported by Burke-Spolaor. No FRBs were discovered in this survey. Taking into
account this result, and other recent surveys at Parkes, we corrected for
detection sensitivities based on the search software used in the analyses and
the different backends used in these surveys and find that the all-sky FRB
event rate for sources with a fluence above 4.0 Jy ms at 1.4 GHz to be FRBs day sky, where the
uncertainties represent a confidence interval. While this rate is lower
than inferred from previous studies, as we demonstrate, this combined event
rate is consistent with the results of all systematic FRB searches at Parkes to
date and does not require the need to postulate a dearth of FRBs at
intermediate latitudes.Comment: Accepted, 10 pages, 6 figure
Recommended from our members
Grid generation methodology and CFD simulations in sliding vane compressors and expanders
The limiting factor for the employment of advanced 3D CFD tools in the analysis and design of rotary vane machines is the unavailability of methods for generation of computational grids suitable for fast and reliable numerical analysis. The paper addresses this challenge presenting the development of an analytical grid generation for vane machines that is based on the user defined nodal displacement. In particular, mesh boundaries are defined as parametric curves generated using trigonometrical modelling of the axial cross section of the machine while the distribution of computational nodes is performed using algebraic algorithms with transfinite interpolation, post orthogonalisation and smoothing. Algebraic control functions are introduced for distribution of nodes on the rotor and casing boundaries in order to achieve good grid quality in terms of cell size and expansion. In this way, the moving and deforming fluid domain of the sliding vane machine is discretized and the conservation of intrinsic quantities in ensured by maintaining the cell connectivity and structure. For validation of generated grids, a mid-size air compressor and a small-scale expander for Organic Rankine Cycle applications have been investigated in this paper. Remarks on implementation of the mesh motion algorithm, stability and robustness experienced with the ANSYS CFX solver as well as the obtained flow results are presente
A short note on a mutation of Cheema-sahebi (Syn. Selection-7)
Kurze Mitteilung iiber eine Mutante von Cheema-sahebi (Syn. Selection-7)Die Trauben- und Beerenmerkmale einer spontan entstandenen Knospenmutante der Tafeltraubensorte Cheema-sahebi werden beschrieben. Die Beeren der Mutante sind gegenüber der Ausgangsform auffällig verlängert. Während diese bei Verpackung und Transport 8-100/o ihrer Beeren verliert, zeichnet sich die Mutante durch eine hohe Haftfestigkeit ihrer Beeren aus
Recommended from our members
Application of numerical grid generation for improved CFD analysis of multiphase screw machines
Algebraic grid generation is widely used for discretization of the working domain of twin screw machines. Algebraic grid generation is fast and has good control over the placement of grid nodes. However, the desired qualities of grid which should be able to handle multiphase flows such as oil injection, may be difficult to achieve at times. In order to obtain fast solution of multiphase screw machines, it is important to further improve the quality and robustness of the computational grid. In this paper, a deforming grid of a twin screw machine is generated using algebraic transfinite interpolation to produce initial mesh upon which an elliptic partial differential equations (PDE) of the Poisson's form is solved numerically to produce smooth final computational mesh. The quality of numerical cells and their distribution obtained by the differential method is greatly improved. In addition, a similar procedure was introduced to fully smoothen the transition of the partitioning rack curve between the rotors thus improving continuous movement of grid nodes and in turn improve robustness and speed of the Computational Fluid Dynamic (CFD) solver. Analysis of an oil injected twin screw compressor is presented to compare the improvements in grid quality factors in the regions of importance such as interlobe space, radial tip and the core of the rotor. The proposed method that combines algebraic and differential grid generation offer significant improvement in grid quality and robustness of numerical solution
- …