1,558 research outputs found
Adaptive acoustooptic filter
A new adaptive filter utilizing acoustooptic devices in a space integrating architecture is described. Two configurations are presented; one of them, suitable for signal estimation, is shown to approximate the Wiener filter, while the other, suitable for detection, is shown to approximate the matched filter
SARAS 2: A Spectral Radiometer for probing Cosmic Dawn and the Epoch of Reionization through detection of the global 21 cm signal
The global 21 cm signal from Cosmic Dawn (CD) and the Epoch of Reionization
(EoR), at redshifts , probes the nature of first sources of
radiation as well as physics of the Inter-Galactic Medium (IGM). Given that the
signal is predicted to be extremely weak, of wide fractional bandwidth, and
lies in a frequency range that is dominated by Galactic and Extragalactic
foregrounds as well as Radio Frequency Interference, detection of the signal is
a daunting task. Critical to the experiment is the manner in which the sky
signal is represented through the instrument. It is of utmost importance to
design a system whose spectral bandpass and additive spurious can be well
calibrated and any calibration residual does not mimic the signal. SARAS is an
ongoing experiment that aims to detect the global 21 cm signal. Here we present
the design philosophy of the SARAS 2 system and discuss its performance and
limitations based on laboratory and field measurements. Laboratory tests with
the antenna replaced with a variety of terminations, including a network model
for the antenna impedance, show that the gain calibration and modeling of
internal additives leave no residuals with Fourier amplitudes exceeding 2~mK,
or residual Gaussians of 25 MHz width with amplitudes exceeding 2~mK. Thus,
even accounting for reflection and radiation efficiency losses in the antenna,
the SARAS~2 system is capable of detection of complex 21-cm profiles at the
level predicted by currently favoured models for thermal baryon evolution.Comment: 44 pages, 17 figures; comments and suggestions are welcom
Waveform Diversity and Range-Coupled Adaptive Radar Signal Processing
Waveform diversity may offer several benefits to radar systems though often at the cost of reduced sensitivity. Multi-dimensional processing schemes are known to offer many degrees of freedom, which can be exploited to suppress the ambiguity inherent to pulse compression, array processing, and Doppler frequency estimation. Spatial waveform diversity can be achieved by transmitting different but correlated waveforms from each element of an antenna array. A simple yet effective scheme is employed to transmit different waveforms in different spatial directions. A new reiterative minimum mean squared error approach entitled Space-Range Adaptive Processing, which adapts simultaneously in range and angle, is derived and shown in simulation to offer enhanced performance when spatial waveform diversity is employed relative to both conventional matched filtering and sequentially adapting in angle and then range. The same mathematical framework is utilized to develop Time-Range Adaptive Processing (TRAP) algorithm which is capable of simultaneously adapting in Doppler frequency and range. TRAP is useful when pulse-to-pulse changing of the center frequency or waveform coding is used to achieve enhanced range resolution or unambiguous ranging, respectively. The inherent computational complexity of the new multi-dimensional algorithms is addressed by segmenting the full-dimension cost functions, yielding a reduced-dimensional variants of each. Finally, a non-adaptive approach based on the multi-dimensional TRAP signal model is utilized to develop an efficient clutter cancellation technique capable of suppressing multiple range intervals of clutter when waveform diversity is applied to pulse-Doppler radar
Efficient Fast-Convolution-Based Waveform Processing for 5G Physical Layer
This paper investigates the application of fast-convolution (FC) filtering
schemes for flexible and effective waveform generation and processing in the
fifth generation (5G) systems. FC-based filtering is presented as a generic
multimode waveform processing engine while, following the progress of 5G new
radio standardization in the Third-Generation Partnership Project, the main
focus is on efficient generation and processing of subband-filtered cyclic
prefix orthogonal frequency-division multiplexing (CP-OFDM) signals. First, a
matrix model for analyzing FC filter processing responses is presented and used
for designing optimized multiplexing of filtered groups of CP-OFDM physical
resource blocks (PRBs) in a spectrally well-localized manner, i.e., with narrow
guardbands. Subband filtering is able to suppress interference leakage between
adjacent subbands, thus supporting independent waveform parametrization and
different numerologies for different groups of PRBs, as well as asynchronous
multiuser operation in uplink. These are central ingredients in the 5G waveform
developments, particularly at sub-6-GHz bands. The FC filter optimization
criterion is passband error vector magnitude minimization subject to a given
subband band-limitation constraint. Optimized designs with different guardband
widths, PRB group sizes, and essential design parameters are compared in terms
of interference levels and implementation complexity. Finally, extensive coded
5G radio link simulation results are presented to compare the proposed approach
with other subband-filtered CP-OFDM schemes and time-domain windowing methods,
considering cases with different numerologies or asynchronous transmissions in
adjacent subbands. Also the feasibility of using independent transmitter and
receiver processing for CP-OFDM spectrum control is demonstrated
Ultra Wideband Communications: from Analog to Digital
Ultrabreitband-Signale (Ultra Wideband [UWB]) können einen
signifikanten Nutzen im Bereich drahtloser Kommunikationssysteme haben. Es
sind jedoch noch einige Probleme offen, die durch Systemdesigner und
Wissenschaftler gelöst werden müssen. Ein Funknetzsystem mit einer derart
großen Bandbreite ist normalerweise auch durch eine große Anzahl an
Mehrwegekomponenten mit jeweils verschiedenen Pfadamplituden
gekennzeichnet. Daher ist es schwierig, die zeitlich verteilte Energie
effektiv zu erfassen. Außerdem ist in vielen Fällen der naheliegende
Ansatz, ein kohärenter Empfänger im Sinne eines signalangepassten Filters
oder eines Korrelators, nicht unbedingt die beste Wahl. In der vorliegenden
Arbeit wird dabei auf die bestehende Problematik und weitere
Lösungsmöglichkeiten eingegangen.
Im ersten Abschnitt geht es um „Impulse Radio UWB”-Systeme mit
niedriger Datenrate. Bei diesen Systemen kommt ein inkohärenter Empfänger
zum Einsatz. Inkohärente Signaldetektion stellt insofern einen
vielversprechenden Ansatz dar, als das damit aufwandsgünstige und robuste
Implementierungen möglich sind. Dies trifft vor allem in Anwendungsfällen
wie den von drahtlosen Sensornetzen zu, wo preiswerte Geräte mit langer
Batterielaufzeit nötigsind. Dies verringert den für die Kanalschätzung
und die Synchronisation nötigen Aufwand, was jedoch auf Kosten der
Leistungseffizienz geht und eine erhöhte Störempfindlichkeit gegenüber
Interferenz (z.B. Interferenz durch mehrere Nutzer oder schmalbandige
Interferenz) zur Folge hat.
Um die Bitfehlerrate der oben genannten Verfahren zu bestimmen, wurde
zunächst ein inkohärenter Combining-Verlust spezifiziert, welcher
auftritt im Gegensatz zu kohärenter Detektion mit Maximum Ratio Multipath
Combining. Dieser Verlust hängt von dem Produkt aus der Länge des
Integrationsfensters und der Signalbandbreite ab.
Um den Verlust durch inkohärentes Combining zu reduzieren und somit die
Leistungseffizienz des Empfängers zu steigern, werden verbesserte
Combining-Methoden für Mehrwegeempfang vorgeschlagen. Ein analoger
Empfänger, bei dem der Hauptteil des Mehrwege-Combinings durch einen
„Integrate and Dump”-Filter implementiert ist, wird für UWB-Systeme
mit Zeit-Hopping gezeigt. Dabei wurde die Einsatzmöglichkeit von dünn
besetzten Codes in solchen System diskutiert und bewertet. Des Weiteren
wird eine Regel für die Code-Auswahl vorgestellt, welche die Stabilität
des Systems gegen Mehrnutzer-Störungen sicherstellt und gleichzeitig den
Verlust durch inkohärentes Combining verringert.
Danach liegt der Fokus auf digitalen Lösungen bei inkohärenter
Demodulation. Im Vergleich zum Analogempfänger besitzt ein
Digitalempfänger einen Analog-Digital-Wandler im Zeitbereich gefolgt von
einem digitalen Optimalfilter. Der digitale Optimalfilter dekodiert den
Mehrfachzugriffscode kohärent und beschränkt das inkohärente Combining
auf die empfangenen Mehrwegekomponenten im Digitalbereich. Es kommt ein
schneller Analog-Digital-Wandler mit geringer Auflösung zum Einsatz, um
einen vertretbaren Energieverbrauch zu gewährleisten. Diese Digitaltechnik
macht den Einsatz langer Analogverzögerungen bei differentieller
Demodulation unnötig und ermöglicht viele Arten der digitalen
Signalverarbeitung. Im Vergleich zur Analogtechnik reduziert sie nicht nur
den inkohärenten Combining-Verlust, sonder zeigt auch eine stärkere
Resistenz gegenüber Störungen. Dabei werden die Auswirkungen der
Auflösung und der Abtastrate der Analog-Digital-Umsetzung analysiert. Die
Resultate zeigen, dass die verminderte Effizienz solcher
Analog-Digital-Wandler gering ausfällt. Weiterhin zeigt sich, dass im
Falle starker Mehrnutzerinterferenz sogar eine Verbesserung der Ergebnisse
zu beobachten ist. Die vorgeschlagenen Design-Regeln spezifizieren die
Anwendung der Analog-Digital-Wandler und die Auswahl der Systemparameter in
Abhängigkeit der verwendeten Mehrfachzugriffscodes und der Modulationsart.
Wir zeigen, wie unter Anwendung erweiterter Modulationsverfahren die
Leistungseffizienz verbessert werden kann und schlagen ein Verfahren zur
Unterdrückung schmalbandiger Störer vor, welches auf Soft Limiting
aufbaut. Durch die Untersuchungen und Ergebnissen zeigt sich, dass
inkohärente Empfänger in UWB-Kommunikationssystemen mit niedriger
Datenrate ein großes Potential aufweisen.
Außerdem wird die Auswahl der benutzbaren Bandbreite untersucht, um einen
Kompromiss zwischen inkohärentem Combining-Verlust und Stabilität
gegenüber langsamen Schwund zu erreichen. Dadurch wurde ein neues Konzept
für UWB-Systeme erarbeitet: wahlweise kohärente oder inkohärente
Empfänger, welche als UWB-Systeme Frequenz-Hopping nutzen. Der wesentliche
Vorteil hiervon liegt darin, dass die Bandbreite im Basisband sich deutlich
verringert. Mithin ermöglicht dies einfach zu realisierende digitale
Signalverarbeitungstechnik mit kostengünstigen Analog-Digital-Wandlern.
Dies stellt eine neue Epoche in der Forschung im Bereich drahtloser
Sensorfunknetze dar.
Der Schwerpunkt des zweiten Abschnitts stellt adaptiven Signalverarbeitung
für hohe Datenraten mit „Direct Sequence”-UWB-Systemen in den
Vordergrund. In solchen Systemen entstehen, wegen der großen Anzahl der
empfangenen Mehrwegekomponenten, starke Inter- bzw.
Intrasymbolinterferenzen. Außerdem kann die Funktionalität des Systems
durch Mehrnutzerinterferenz und Schmalbandstörungen deutlich beeinflusst
werden. Um sie zu eliminieren, wird die „Widely Linear”-Rangreduzierung
benutzt. Dabei verbessert die Rangreduzierungsmethode das
Konvergenzverhalten, besonders wenn der gegebene Vektor eine sehr große
Anzahl an Abtastwerten beinhaltet (in Folge hoher einer Abtastrate).
Zusätzlich kann das System durch die Anwendung der R-linearen Verarbeitung
die Statistik zweiter Ordnung des nicht-zirkularen Signals vollständig
ausnutzen, was sich in verbesserten Schätzergebnissen widerspiegelt.
Allgemeine kann die Methode der „Widely Linear”-Rangreduzierung auch in
andern Bereichen angewendet werden, z.B. in „Direct
Sequence”-Codemultiplexverfahren (DS-CDMA), im MIMO-Bereich, im Global
System for Mobile Communications (GSM) und beim Beamforming.The aim of this thesis is to investigate key issues encountered in the
design of transmission schemes and receiving techniques for Ultra Wideband
(UWB) communication systems. Based on different data rate applications,
this work is divided into two parts, where energy efficient and robust
physical layer solutions are proposed, respectively.
Due to a huge bandwidth of UWB signals, a considerable amount of multipath
arrivals with various path gains is resolvable at the receiver. For low
data rate impulse radio UWB systems, suboptimal non-coherent detection is a
simple way to effectively capture the multipath energy. Feasible techniques
that increase the power efficiency and the interference robustness of
non-coherent detection need to be investigated. For high data rate direct
sequence UWB systems, a large number of multipath arrivals results in
severe inter-/intra-symbol interference. Additionally, the system
performance may also be deteriorated by multi-user interference and
narrowband interference. It is necessary to develop advanced signal
processing techniques at the receiver to suppress these interferences.
Part I of this thesis deals with the co-design of signaling schemes and
receiver architectures in low data rate impulse radio UWB systems based on
non-coherent detection.● We analyze the bit error rate performance of
non-coherent detection and characterize a non-coherent combining loss,
i.e., a performance penalty with respect to coherent detection with maximum
ratio multipath combining. The thorough analysis of this loss is very
helpful for the design of transmission schemes and receive techniques
innon-coherent UWB communication systems.● We propose to use optical
orthogonal codes in a time hopping impulse radio UWB system based on an
analog non-coherent receiver. The “analog” means that the major part of
the multipath combining is implemented by an integrate and dump filter. The
introduced semi-analytical method can help us to easily select the time
hopping codes to ensure the robustness against the multi-user interference
and meanwhile to alleviate the non-coherent combining loss.● The main
contribution of Part I is the proposal of applying fully digital solutions
in non-coherent detection. The proposed digital non-coherent receiver is
based on a time domain analog-to-digital converter, which has a high speed
but a very low resolution to maintain a reasonable power consumption.
Compared to its analog counterpart, itnot only significantly reduces the
non-coherent combining loss but also offers a higher interference
robustness. In particular, the one-bit receiver can effectively suppress
strong multi-user interference and is thus advantageous in separating
simultaneously operating piconets.The fully digital solutions overcome the
difficulty of implementing long analog delay lines and make differential
UWB detection possible. They also facilitate the development of various
digital signal processing techniques such as multi-user detection and
non-coherent multipath combining methods as well as the use of advanced
modulationschemes (e.g., M-ary Walsh modulation).● Furthermore, we
present a novel impulse radio UWB system based on frequency hopping, where
both coherent and non-coherent receivers can be adopted. The key advantage
is that the baseband bandwidth can be considerably reduced (e.g., lower
than 500 MHz), which enables low-complexity implementation of the fully
digital solutions. It opens up various research activities in the
application field of wireless sensor networks.
Part II of this thesis proposes adaptive widely linear reduced-rank
techniques to suppress interferences for high data rate direct sequence UWB
systems, where second-order non-circular signals are used. The reduced-rank
techniques are designed to improve the convergence performance and the
interference robustness especially when the received vector contains a
large number of samples (due to a high sampling rate in UWB systems). The
widely linear processing takes full advantage of the second-order
statistics of the non-circular signals and enhances the estimation
performance. The generic widely linear reduced-rank concept also has a
great potential in the applications of other systems such as Direct
Sequence Code Division Multiple Access (DS-CDMA), Multiple Input Multiple
Output (MIMO) system, and Global System for Mobile Communications (GSM), or
in other areas such as beamforming
Interception Algorithm of S-cubed Signal Model in Stealth Radar Equipment
AbstractRadar equipment of stealth platforms such as aircraft have adopted the newest modern technology to design the signal waveforms. One of the important and effective methods is the hybrid waveform called spread spectrum stretch (S-cubed) which combines linear frequency modulation (LFM) and discrete phase code. In order to investigate the function of enemy's stealth radar equipment, the interception algorithm of S-cubed is needed. In this paper, a novel detection and parameter estimation approach for the reconnaissance S-cubed radar signal is presented. First, the generalized time-frequency representation of Zhao, Atlas, and Marks (ZAM-GTFR) and Hough transforms (HT) are applied to detecting the signal, and then the initial frequency and modulation slope of LFM are estimated from the ZAM-GTFR. On the basis of LFM information, the reconstructing signal is generated. Finally, the code rate of discrete phase code is extracted from the negative peaks of the ZAM-GTFR. Simulation results show that the proposed algorithm has higher estimation accuracy when the signal to noise ratio (SNR) is above 3 dB
A General Framework for Analyzing, Characterizing, and Implementing Spectrally Modulated, Spectrally Encoded Signals
Fourth generation (4G) communications will support many capabilities while providing universal, high speed access. One potential enabler for these capabilities is software defined radio (SDR). When controlled by cognitive radio (CR) principles, the required waveform diversity is achieved via a synergistic union called CR-based SDR. Research is rapidly progressing in SDR hardware and software venues, but current CR-based SDR research lacks the theoretical foundation and analytic framework to permit efficient implementation. This limitation is addressed here by introducing a general framework for analyzing, characterizing, and implementing spectrally modulated, spectrally encoded (SMSE) signals within CR-based SDR architectures. Given orthogonal frequency division multiplexing (OFDM) is a 4G candidate signal, OFDM-based signals are collectively classified as SMSE since modulation and encoding are spectrally applied. The proposed framework provides analytic commonality and unification of SMSE signals. Applicability is first shown for candidate 4G signals, and resultant analytic expressions agree with published results. Implementability is then demonstrated in multiple coexistence scenarios via modeling and simulation to reinforce practical utility
Recommended from our members
Anti-Jam GPS Controlled Reception Pattern Antennas for Man-Portable Applications
Military GPS receivers provide crucial information to soldiers in the field, however, the performance of these devices is degraded by in band RF interference, making GPS susceptible to jamming. Anti-jam techniques for aircraft and vehicular platforms have been developed, but at present there is no system for dismounted soldiers. There is a need for an anti-jam system which meets the demands of a dismounted soldier and conforms to the size, weight, and power requirements of a portable device.
A controlled reception pattern antenna, or CRPA, is a potential solution for jammer mitigation. These devices work by steering reception pattern nulls toward the jammer direction, reducing the jammer power which reaches the GPS receiver. Prior CRPA realizations have been designed for use on vehicular and aircraft applications, however, these platforms do not suffer from the same limitations as a man-portable CRPA. Three considerations which are more pertinent for man-portable designs than prior work are (i) distributed antenna element positions and orientations dynamically change during use changing the reception pattern characteristics, (ii) the user is lower to the ground and moves through the environment meaning that multipath propagation can have a greater effect on CRPA performance, and (iii) the size weight and power constraints for a portable system limit the number of antenna elements reducing the degrees of freedom that can be used for cancellation.
To address these challenges, a framework for man-portable CRPA modeling is presented. This includes development of efficient modeling methods which enable investigations into element perturbations to address the dynamic orientation problem. These and other methods are presented in Chapter 3, along with a discussion of the relative strengths and weaknesses of each. Additionally, a mixed scattering channel model is applied to the CRPA reception patterns, combining diffuse and specular reflection in Chapter 4. Discussion of this model centers around the eigenvalues of the signal covariance matrix and the effect of coherence between multipath components. Following this, Chapter 5 examines the performance of polarimetric CRPAs and space-time adaptive processing for man-portable CRPAs with limited degrees of freedom
- …