Network effects of intelligent speed adaptation systems

Intelligent Speed Adaptation (ISA) systems use in-vehicle electronic devices to enable the speed of vehicles to be regulated externally. They are increasingly appreciated as a flexible method for speed management and control, particularly in urban areas. On-road trials using a small numbers of ISA equipped vehicles have been carried out in Sweden, the Netherlands, Spain and the UK. This paper describes the developments made to enhance a traffic microsimulation model in order to represent ISA implemented across a network and their impact on the networks. The simulation modelling of the control system is carried out on a real-world urban network, and the impacts on traffic congestion, speed distribution and the environment assessed. The results show that ISA systems are more effective in less congested traffic conditions. Momentary high speeds in traffic are effectively suppressed, resulting in a reduction in speed variation which is likely to have a positive impact on safety. Whilst ISA reduces excessive traffic speeds in the network, it does not affect average journey times. In particular, the total vehicle-hours travelling at speeds below 10 km/hr have not changed, indicating that the speed control had not induced more slow-moving queues to the network. A significant, eight percent, reduction in fuel consumption was found with full ISA penetration. These results are in accordance with those from field trials and they provide the basis for cost-benefit analyses on introducing ISA into the vehicle fleet. Contrary to earlier findings from the Swedish ISA road trials, these network simulations showed that ISA had no significant effect on emission of gaseous pollutants CO, NOx and HC. Further research is planned to investigate the impact on emission with a more comprehensive and up to date modal emission factor database

Increasing exhaust temperature to enable after-treatment operation on a two-stage turbo-charged medium speed marine diesel engine

Nitrogen-oxides (NOx) are becoming more and more regulated. In heavy duty, medium speed engines these emission limits are also being reduced steadily: Selective catalytic reduction is a proven technology which allows to reduce NOx emission with very high efficiency. However, operating temperature of the catalytic converter has to be maintained within certain limits as conversion efficiency and ammonia slip are very heavily influenced by temperature. In this work the engine calibration and hardware will be modified to allow for a wide engine operating range with Selective catalytic reduction. The studied engine has 4MW nominal power and runs at 750rpm engine speed, fuel consumption during engine tests becomes quite expensive (+- 750kg/h) for a measurement campaign. This is why a simulation model was developed and validated. This model was then used to investigate several strategies to control engine out temperature: different types of wastegates, injection variation and valve timing adjustments. Simulation showed that wastegate application had the best tradeoff between fuel consumption and exhaust temperature. Finally, this configuration was built on the engine test bench and results from both measurements and simulation agreed very well

A Comparison of Inlet Valve Operating Strategies in a Single-Cylinder Spark-Ignition Engine

This experimental work was concerned with comparison of inlet valve actuation strategies in a thermodynamic single cylinder spark ignition research engine equipped with a mechanical fully variable valvetrain on both the inlet and exhaust. The research involved study of the effects of the valvetrain on combustion, fuel economy and emissions when used to achieve variable valve timing alone and when applied together with early inlet valve closing for so-called unthrottled operation. The effects of such early inlet valve closure were examined using either fully variable events or by simulating two-stage cam profile switching. While fully variable operation enabled the maximum fuel savings over the widest operating map, it was apparent that two-stage switching mechanisms can provide an attractive compromise in terms of cost versus CO 2 benefit on engines of moderate to large capacity. However, from speed-load maps obtained in the current study it would appear that a wide range of inlet valve durations would be necessary to obtain fuel savings sufficient to warrant a system any more sophisticated than current variable valve timing mechanisms in future aggressively downsized gasoline engines. © IMechE, 2009

General aviation piston-engine exhaust emission reduction

To support the promulgation of aircraft regulations, two airports were examined, Van Nuys and Tamiami. It was determined that the carbon monoxide (CO) emissions from piston-engine aircraft have a significant influence on the CO levels in the ambient air in and around airports, where workers and travelers would be exposed. Emissions standards were set up for control of emissions from aircraft piston engines manufactured after December 31, 1979. The standards selected were based on a technologically feasible and economically reasonable control of carbon monoxide. It was concluded that substantial CO reductions could be realized if the range of typical fuel-air ratios could be narrowed. Thus, improvements in fuel management were determined as reasonable controls

A Study on the Integration of a High-Speed Flywheel as an Energy Storage Device in Hybrid Vehicles

The last couple of decades have seen the rise of the hybrid electric vehicle as a compromise between the outstanding specific energy of petrol fuels and its low-cost technology, and the zero tail-gate emissions of the electric vehicle. Despite this, considerable reductions in cost and further increases in fuel economy are needed for their widespread adoption. An alternative low-cost energy storage technology for vehicles is the high-speed flywheel. The flywheel has important limitations that exclude it from being used as a primary energy source for vehicles, but its power characteristics and low-cost materials make it a powerful complement to a vehicle's primary propulsion system. This thesis presents an analysis on the integration of a high-speed flywheel for use as a secondary energy storage device in hybrid vehicles. Unlike other energy storage technologies, the energy content of the flywheel has a direct impact on the velocity of transmission. This presents an important challenge, as it means that the flywheel must be able to rotate at a speed independent of the vehicle's velocity and therefore it must be coupled via a variable speed transmission. This thesis presents some practical ways in which to accomplish this in conventional road vehicles, namely with the use of a variator, a planetary gear set or with the use of a power-split continuously variable transmission. Fundamental analyses on the kinematic behaviour of these transmissions particularly as they pertain to flywheel powertrains are presented. Computer simulations were carried out to compare the performance of various transmissions, and the models developed are presented as well. Finally the thesis also contains an investigation on the driving and road conditions that have the most beneficial effect on hybrid vehicle performance, with a particular emphasis on the effect that the road topography has on fuel economy and the significance of this

Exhaust emissions reduction for intermittent combustion aircraft engines

Three concepts which, to an aircraft piston engine, provide reductions in exhaust emissions of hydrocarbons and carbon monoxide while simultaneously improving fuel economy. The three chosen concepts, (1) an improved fuel injection system, (2) an improved cooling cylinder head, and (3) exhaust air injection, when combined, show a synergistic relationship in achieving these goals. In addition, the benefits of variable ignition timing were explored and both dynamometer and flight testing of the final engine configuration were accomplished

Development of low liquid fuel Burnera

Recently, most of the gas turbine combustion research and development involves in lowering the emissions emitted from the combustor. Emission causes adverse affect to the world and mankind especially. Main concern of the present work is to reduce the NOx emission since the CO emission could be reduced through homogeneous mixing of fuel and air. Homogeneous mixing of fuel and air is also needed in order to reduce NOx emission. A liquid fuel burner system with radial air swirler vane angle of 30o, 40o, 50o and 60o has been investigated using 163mm inside diameter combustor. Orifice plates with three different sizes of 20mm, 25mm and 30mm were inserted at the back plate of swirler outlet. All tests were conducted using diesel as fuel. Fuel was injected at two different positions, i.e. at upstream and downstream of the swirler outlet using central fuel injector with single fuel nozzle pointing axially outwards. Experiment has been carried out to compare the three emissions NOx, CO and SO2. NOx reduction of about 53 percent was achieved for orifice plate of 20mm with downstream injection compared to orifice plate of 20mm with upstream injection. CO2 and SO2 was reduced about 26 percent and 56 percent respectively for the same configuration. This comparison was taken using swirler vane angle of 60o. The overall study shows that larger swirler vane angle produces lower emission results compared to the smaller ones. Smaller orifice plates produce better emission reduction. Meanwhile, downstream injection position significantly decreases the emission levels compared to upstream injection position. Combination of smallest orifice plate and largest swirler vane angle with downstream injection produce widest and shortest flame length

Investigation of cylinder deactivation and variable valve actuation on gasoline engine performance

Increasingly stringent regulations on gasoline engine fuel consumption and exhaust emissions require additional technology integration such as Cylinder Deactivation (CDA) and Variable valve actuation (VVA) to improve part load engine efficiency. At part load, CDA is achieved by closing the inlet and exhaust valves and shutting off the fuel supply to a selected number of cylinders. Variable valve actuation (VVA) enables the cylinder gas exchange process to be optimised for different engine speeds by changing valve opening and closing times as well as maximum valve lift. The focus of this study was the investigation of effect of the integration of the above two technologies on the performance of a gasoline engine operating at part load conditions. In this study, a 1.6 Litre in-line 4-cylinder gasoline engine is modelled on engine simulation software and simulated data is analysed to show improvements in fuel consumption, CO2 emissions, pumping losses and effects on CO and NOx emissions. A CDA and VVA operating window is identified which yields brake specific fuel consumption improvements of 10-20% against the base engine at engine speeds between 1000rpm to 3500rpm at approximately 12.5% load. Highest concentration of CO emissions was observed at between 4 to 5 bar BMEP at 4000rpm and highest concentration of NOx at the same load range but at 1000rpm.Findings based on simulation results point towards significant part load performance improvements which can be achieved by integrating cylinder deactivation and variable valve actuation on gasoline engines. Copyright © 2014 SAE International