REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains

Cost modelling and concurrent engineering for testable design

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.As integrated circuits and printed circuit boards increase in complexity, testing becomes a major cost factor of the design and production of the complex devices. Testability has to be considered during the design of complex electronic systems, and automatic test systems have to be used in order to facilitate the test. This fact is now widely accepted in industry. Both design for testability and the usage of automatic test systems aim at reducing the cost of production testing or, sometimes, making it possible at all. Many design for testability methods and test systems are available which can be configured into a production test strategy, in order to achieve high quality of the final product. The designer has to select from the various options for creating a test strategy, by maximising the quality and minimising the total cost for the electronic system. This thesis presents a methodology for test strategy generation which is based on consideration of the economics during the life cycle of the electronic system. This methodology is a concurrent engineering approach which takes into account all effects of a test strategy on the electronic system during its life cycle by evaluating its related cost. This objective methodology is used in an original test strategy planning advisory system, which allows for test strategy planning for VLSI circuits as well as for digital electronic systems. The cost models which are used for evaluating the economics of test strategies are described in detail and the test strategy planning system is presented. A methodology for making decisions which are based on estimated costing data is presented. Results of using the cost models and the test strategy planning system for evaluating the economics of test strategies for selected industrial designs are presented

Testability and redundancy techniques for improved yield and reliability of CMOS VLSI circuits

The research presented in this thesis is concerned with the design of fault-tolerant integrated circuits as a contribution to the design of fault-tolerant systems. The economical manufacture of very large area ICs will necessitate the incorporation of fault-tolerance features which are routinely employed in current high density dynamic random access memories. Furthermore, the growing use of ICs in safety-critical applications and/or hostile environments in addition to the prospect of single-chip systems will mandate the use of fault-tolerance for improved reliability. A fault-tolerant IC must be able to detect and correct all possible faults that may affect its operation. The ability of a chip to detect its own faults is not only necessary for fault-tolerance, but it is also regarded as the ultimate solution to the problem of testing. Off-line periodic testing is selected for this research because it achieves better coverage of physical faults and it requires less extra hardware than on-line error detection techniques. Tests for CMOS stuck-open faults are shown to detect all other faults. Simple test sequence generation procedures for the detection of all faults are derived. The test sequences generated by these procedures produce a trivial output, thereby, greatly simplifying the task of test response analysis. A further advantage of the proposed test generation procedures is that they do not require the enumeration of faults. The implementation of built-in self-test is considered and it is shown that the hardware overhead is comparable to that associated with pseudo-random and pseudo-exhaustive techniques while achieving a much higher fault coverage through-the use of the proposed test generation procedures. The consideration of the problem of testing the test circuitry led to the conclusion that complete test coverage may be achieved if separate chips cooperate in testing each other's untested parts. An alternative approach towards complete test coverage would be to design the test circuitry so that it is as distributed as possible and so that it is tested as it performs its function. Fault correction relies on the provision of spare units and a means of reconfiguring the circuit so that the faulty units are discarded. This raises the question of what is the optimum size of a unit? A mathematical model, linking yield and reliability is therefore developed to answer such a question and also to study the effects of such parameters as the amount of redundancy, the size of the additional circuitry required for testing and reconfiguration, and the effect of periodic testing on reliability. The stringent requirement on the size of the reconfiguration logic is illustrated by the application of the model to a typical example. Another important result concerns the effect of periodic testing on reliability. It is shown that periodic off-line testing can achieve approximately the same level of reliability as on-line testing, even when the time between tests is many hundreds of hours

Methodology and Ecosystem for the Design of a Complex Network ASIC

Performance of HPC systems has risen steadily. While the 10 Petaflop/s barrier has been breached in the year 2011 the next large step into the exascale era is expected sometime between the years 2018 and 2020. The EXTOLL project will be an integral part in this venture. Originally designed as a research project on FPGA basis it will make the transition to an ASIC to improve its already excelling performance even further. This transition poses many challenges that will be presented in this thesis. Nowadays, it is not enough to look only at single components in a system. EXTOLL is part of complex ecosystem which must be optimized overall since everything is tightly interwoven and disregarding some aspects can cause the whole system either to work with limited performance or even to fail. This thesis examines four different aspects in the design hierarchy and proposes efficient solutions or improvements for each of them. At first it takes a look at the design implementation and the differences between FPGA and ASIC design. It introduces a methodology to equip all on-chip memory with ECC logic automatically without the user’s input and in a transparent way so that the underlying code that uses the memory does not have to be changed. In the next step the floorplanning process is analyzed and an iterative solution is worked out based on physical and logical constraints of the EXTOLL design. Besides, a work flow for collaborative design is presented that allows multiple users to work on the design concurrently. The third part concentrates on the high-speed signal path from the chip to the connector and how it is affected by technological limitations. All constraints are analyzed and a package layout for the EXTOLL chip is proposed that is seen as the optimal solution. The last part develops a cost model for wafer and package level test and raises technological concerns that will affect the testing methodology. In order to run testing internally it proposes the development of a stand-alone test platform that is able to test packaged EXTOLL chips in every aspect

Fault and Defect Tolerant Computer Architectures: Reliable Computing With Unreliable Devices

This research addresses design of a reliable computer from unreliable device technologies. A system architecture is developed for a fault and defect tolerant (FDT) computer. Trade-offs between different techniques are studied and yield and hardware cost models are developed. Fault and defect tolerant designs are created for the processor and the cache memory. Simulation results for the content-addressable memory (CAM)-based cache show 90% yield with device failure probabilities of 3 x 10(-6), three orders of magnitude better than non fault tolerant caches of the same size. The entire processor achieves 70% yield with device failure probabilities exceeding 10(-6). The required hardware redundancy is approximately 15 times that of a non-fault tolerant design. While larger than current FT designs, this architecture allows the use of devices much more likely to fail than silicon CMOS. As part of model development, an improved model is derived for NAND Multiplexing. The model is the first accurate model for small and medium amounts of redundancy. Previous models are extended to account for dependence between the inputs and produce more accurate results

Designing Efficient Network Interfaces For System Area Networks

The network is the key component of a Cluster of Workstations/PCs. Its performance, measured in terms of bandwidth and latency, has a great impact on the overall system performance. It quickly became clear that traditional WAN/LAN technology is not too well suited for interconnecting powerful nodes into a cluster. Their poor performance too often slows down communication-intensive applications. This observation led to the birth of a new class of networks called System Area Networks (SAN). The ATOLL network introduces a new optimized architecture for SANs. On a single chip, not one but four network interfaces (NI) have been implemented, together with an on-chip 4x4 full-duplex switch and four link interfaces. This unique "Network on a Chip" architecture is best suited for interconnecting SMP nodes, where multiple CPUs are given an exclusive NI and do not have to share a single interface. It also removes the need for any additional switching hardware, since the four byte-wide full-duplex links can be connected by cables with neighbor nodes in an arbitrary network topology

An Evaluation of the application of partial evaluation on color lookup table implementations

A number of SRAM-based field-programmable gate arrays (FPGAs) allow for partial reconfiguration, allowing a part of the device to be reconfigured while the rest of the device continues operating. Partial evaluation, or instance-specific design, allows a design to be optimized to a specific set of inputs. When combined with partial reconfiguration, the reconfigurable module can be reinstantiated based on the inputs to be processed and improve the performance of the design. This thesis explores the effects, particularly the performance vs flexibility tradeoff, of using partial evaluation on the color look-up tables (CLUTs) of a color-space conversion module implemented on an FPGA. This thesis examines the impact of implementing the CLUTs as distributed RAMs, distributed ROMs, and block ROMs, as well as examining the effects of initializing block RAMs

Network-on-Chip

Addresses the Challenges Associated with System-on-Chip Integration Network-on-Chip: The Next Generation of System-on-Chip Integration examines the current issues restricting chip-on-chip communication efficiency, and explores Network-on-chip (NoC), a promising alternative that equips designers with the capability to produce a scalable, reusable, and high-performance communication backbone by allowing for the integration of a large number of cores on a single system-on-chip (SoC). This book provides a basic overview of topics associated with NoC-based design: communication infrastructure design, communication methodology, evaluation framework, and mapping of applications onto NoC. It details the design and evaluation of different proposed NoC structures, low-power techniques, signal integrity and reliability issues, application mapping, testing, and future trends. Utilizing examples of chips that have been implemented in industry and academia, this text presents the full architectural design of components verified through implementation in industrial CAD tools. It describes NoC research and developments, incorporates theoretical proofs strengthening the analysis procedures, and includes algorithms used in NoC design and synthesis. In addition, it considers other upcoming NoC issues, such as low-power NoC design, signal integrity issues, NoC testing, reconfiguration, synthesis, and 3-D NoC design. This text comprises 12 chapters and covers: The evolution of NoC from SoC—its research and developmental challenges NoC protocols, elaborating flow control, available network topologies, routing mechanisms, fault tolerance, quality-of-service support, and the design of network interfaces The router design strategies followed in NoCs The evaluation mechanism of NoC architectures The application mapping strategies followed in NoCs Low-power design techniques specifically followed in NoCs The signal integrity and reliability issues of NoC The details of NoC testing strategies reported so far The problem of synthesizing application-specific NoCs Reconfigurable NoC design issues Direction of future research and development in the field of NoC Network-on-Chip: The Next Generation of System-on-Chip Integration covers the basic topics, technology, and future trends relevant to NoC-based design, and can be used by engineers, students, and researchers and other industry professionals interested in computer architecture, embedded systems, and parallel/distributed systems

Efficient implementation of video processing algorithms on FPGA

The work contained in this portfolio thesis was carried out as part of an Engineering Doctorate (Eng.D) programme from the Institute for System Level Integration. The work was sponsored by Thales Optronics, and focuses on issues surrounding the implementation of video processing algorithms on field programmable gate arrays (FPGA). A description is given of FPGA technology and the currently dominant methods of designing and verifying firmware. The problems of translating a description of behaviour into one of structure are discussed, and some of the latest methodologies for tackling this problem are introduced. A number of algorithms are then looked at, including methods of contrast enhancement, deconvolution, and image fusion. Algorithms are characterised according to the nature of their execution flow, and this is used as justification for some of the design choices that are made. An efficient method of performing large two-dimensional convolutions is also described. The portfolio also contains a discussion of an FPGA implementation of a PID control algorithm, an overview of FPGA dynamic reconfigurability, and the development of a demonstration platform for rapid deployment of video processing algorithms in FPGA hardware

High level behavioural modelling of boundary scan architecture.

This project involves the development of a software tool which enables the integration of the IEEE 1149.1/JTAG Boundary Scan Test Architecture automatically into an ASIC (Application Specific Integrated Circuit) design. The tool requires the original design (the ASIC) to be described in VHDL-IEEE 1076 Hardware Description Language. The tool consists of the two major elements: i) A parsing and insertion algorithm developed and implemented in 'C'; ii) A high level model of the Boundary Scan Test Architecture implemented in 'VHDL'. The parsing and insertion algorithm is developed to deal with identifying the design Input/Output (I/O) terminals, their types and the order they appear in the ASIC design. It then attaches suitable Boundary Scan Cells to each I/O, except power and ground and inserts the high level models of the full Boundary Scan Architecture into the ASIC without altering the design core structure