Evaluation of a Field Programmable Gate Array Circuit Reconfiguration System

This research implements a circuit reconfiguration system (CRS) to reconfigure a field programmable gate array (FPGA) in response to a faulty configurable logic block (CLB). It is assumed that the location of the fault is known and the CLB is moved according to one of four replacement methods: column left, column right, row up, and row down. Partial reconfiguration of the FPGA is done through the Joint Test Action Group (JTAG) port to produce the desired logic block movement. The time required to accomplish the reconfiguration is measured for each method in both clear and congested areas of the FPGA. The measured data indicate that there is no consistently better replacement method, regardless of the circuit congestion or location within the FPGA. Thus, given a specific location in the FPGA, there is no preferred replacement method that will result in the lowest reconfiguration time

Interconnect yield analysis and fault tolerance for field programmable gate arrays

Imperial Users onl

Design and application of reconfigurable circuits and systems

Open Acces

New Design Techniques for Dynamic Reconfigurable Architectures

L'abstract è presente nell'allegato / the abstract is in the attachmen

Proceedings of the 5th International Workshop on Reconfigurable Communication-centric Systems on Chip 2010 - ReCoSoC\u2710 - May 17-19, 2010 Karlsruhe, Germany. (KIT Scientific Reports ; 7551)

ReCoSoC is intended to be a periodic annual meeting to expose and discuss gathered expertise as well as state of the art research around SoC related topics through plenary invited papers and posters. The workshop aims to provide a prospective view of tomorrow\u27s challenges in the multibillion transistor era, taking into account the emerging techniques and architectures exploring the synergy between flexible on-chip communication and system reconfigurability

Low-overhead fault-tolerant logic for field-programmable gate arrays

While allowing for the fabrication of increasingly complex and efficient circuitry, transistor shrinkage and count-per-device expansion have major downsides: chiefly increased variation, degradation and fault susceptibility. For this reason, design-time consideration of faults will have to be given to increasing numbers of electronic systems in the future to ensure yields, reliabilities and lifetimes remain acceptably high. Many mathematical operators commonly accelerated in hardware are suited to modification resulting in datapath error detection and correction capabilities with far lower area, performance and/or power consumption overheads than those incurred through the utilisation of more established, general-purpose fault tolerance methods such as modular redundancy. Field-programmable gate arrays are uniquely placed to allow further area savings to be made thanks to their dynamic reconfigurability. The majority of the technical work presented within this thesis is based upon a benchmark hardware accelerator---a matrix multiplier---that underwent several evolutions in order to detect and correct faults manifesting along its datapath at runtime. In the first instance, fault detectability in excess of 99% was achieved in return for 7.87% additional area and 45.5% extra latency. In the second, the ability to correct errors caused by those faults was added at the cost of 4.20% more area, while 50.7% of this---and 46.2% of the previously incurred latency overhead---was removed through the introduction of partial reconfiguration in the third. The fourth demonstrates further reductions in both area and performance overheads---of 16.7% and 8.27%, respectively---through systematic data width reduction by allowing errors of less than ±0.5% of the maximum output value to propagate.Open Acces

Fault and Defect Tolerant Computer Architectures: Reliable Computing With Unreliable Devices

This research addresses design of a reliable computer from unreliable device technologies. A system architecture is developed for a fault and defect tolerant (FDT) computer. Trade-offs between different techniques are studied and yield and hardware cost models are developed. Fault and defect tolerant designs are created for the processor and the cache memory. Simulation results for the content-addressable memory (CAM)-based cache show 90% yield with device failure probabilities of 3 x 10(-6), three orders of magnitude better than non fault tolerant caches of the same size. The entire processor achieves 70% yield with device failure probabilities exceeding 10(-6). The required hardware redundancy is approximately 15 times that of a non-fault tolerant design. While larger than current FT designs, this architecture allows the use of devices much more likely to fail than silicon CMOS. As part of model development, an improved model is derived for NAND Multiplexing. The model is the first accurate model for small and medium amounts of redundancy. Previous models are extended to account for dependence between the inputs and produce more accurate results

Delay Measurements and Self Characterisation on FPGAs

This thesis examines new timing measurement methods for self delay characterisation of Field-Programmable Gate Arrays (FPGAs) components and delay measurement of complex circuits on FPGAs. Two novel measurement techniques based on analysis of a circuit's output failure rate and transition probability is proposed for accurate, precise and efficient measurement of propagation delays. The transition probability based method is especially attractive, since it requires no modifications in the circuit-under-test and requires little hardware resources, making it an ideal method for physical delay analysis of FPGA circuits. The relentless advancements in process technology has led to smaller and denser transistors in integrated circuits. While FPGA users benefit from this in terms of increased hardware resources for more complex designs, the actual productivity with FPGA in terms of timing performance (operating frequency, latency and throughput) has lagged behind the potential improvements from the improved technology due to delay variability in FPGA components and the inaccuracy of timing models used in FPGA timing analysis. The ability to measure delay of any arbitrary circuit on FPGA offers many opportunities for on-chip characterisation and physical timing analysis, allowing delay variability to be accurately tracked and variation-aware optimisations to be developed, reducing the productivity gap observed in today's FPGA designs. The measurement techniques are developed into complete self measurement and characterisation platforms in this thesis, demonstrating their practical uses in actual FPGA hardware for cross-chip delay characterisation and accurate delay measurement of both complex combinatorial and sequential circuits, further reinforcing their positions in solving the delay variability problem in FPGAs

Design Disjunction for Resilient Reconfigurable Hardware

Contemporary reconfigurable hardware devices have the capability to achieve high performance, power efficiency, and adaptability required to meet a wide range of design goals. With scaling challenges facing current complementary metal oxide semiconductor (CMOS), new concepts and methodologies supporting efficient adaptation to handle reliability issues are becoming increasingly prominent. Reconfigurable hardware and their ability to realize self-organization features are expected to play a key role in designing future dependable hardware architectures. However, the exponential increase in density and complexity of current commercial SRAM-based field-programmable gate arrays (FPGAs) has escalated the overhead associated with dynamic runtime design adaptation. Traditionally, static modular redundancy techniques are considered to surmount this limitation; however, they can incur substantial overheads in both area and power requirements. To achieve a better trade-off among performance, area, power, and reliability, this research proposes design-time approaches that enable fine selection of redundancy level based on target reliability goals and autonomous adaptation to runtime demands. To achieve this goal, three studies were conducted: First, a graph and set theoretic approach, named Hypergraph-Cover Diversity (HCD), is introduced as a preemptive design technique to shift the dominant costs of resiliency to design-time. In particular, union-free hypergraphs are exploited to partition the reconfigurable resources pool into highly separable subsets of resources, each of which can be utilized by the same synthesized application netlist. The diverse implementations provide reconfiguration-based resilience throughout the system lifetime while avoiding the significant overheads associated with runtime placement and routing phases. Evaluation on a Motion-JPEG image compression core using a Xilinx 7-series-based FPGA hardware platform has demonstrated the potential of the proposed FT method to achieve 37.5% area saving and up to 66% reduction in power consumption compared to the frequently-used TMR scheme while providing superior fault tolerance. Second, Design Disjunction based on non-adaptive group testing is developed to realize a low-overhead fault tolerant system capable of handling self-testing and self-recovery using runtime partial reconfiguration. Reconfiguration is guided by resource grouping procedures which employ non-linear measurements given by the constructive property of f-disjunctness to extend runtime resilience to a large fault space and realize a favorable range of tradeoffs. Disjunct designs are created using the mosaic convergence algorithm developed such that at least one configuration in the library evades any occurrence of up to d resource faults, where d is lower-bounded by f. Experimental results for a set of MCNC and ISCAS benchmarks have demonstrated f-diagnosability at the individual slice level with average isolation resolution of 96.4% (94.4%) for f=1 (f=2) while incurring an average critical path delay impact of only 1.49% and area cost roughly comparable to conventional 2-MR approaches. Finally, the proposed Design Disjunction method is evaluated as a design-time method to improve timing yield in the presence of large random within-die (WID) process variations for application with a moderately high production capacity