Openwifi : a free and open-source IEEE802.11 SDR implementation on SoC

Open source Software Defined Radio (SDR) project, such as srsLTE and Open Air Interface (OAI), has been widely used for 4G/5G research. However the SDR implementation of the IEEE802.11 (Wi-Fi) is still difficult. The Wi-Fi Short InterFrame Space (SIFS) requires acknowledgement (ACK) packet being sent out in 10μs/16μs(2.4 GHz/5GHz) after receiving a packet successfully, thus the Personal Computer (PC) based SDR architecture hardly can be used due to the latency (≥100μs) between PC and Radio Frequency (RF) front-end. Researchers have to do simulation, hack a commercial chip or buy an expensive reference design to test their ideas. To change this situation, we have developed an open-source full-stack IEEE802.11a/g/n SDR implementation — openwifi. It is based on Xilinx Zynq Systemon-Chip (SoC) that includes Field Programmable Gate Array (FPGA) and ARM processor. With the low latency connection between FPGA and RF front-end, the most critical SIFS timing is achieved by implementing Physical layer (PHY) and low level Media Access Control (low MAC) in FPGA. The corresponding driver is implemented in the embedded Linux running on the ARM processor. The driver instantiates Application Programming Interfaces (APIs) defined by Linux mac80211 subsystem, which is widely used for most SoftMAC Wi-Fi chips. Researchers could study and modify openwifi easily thanks to the modular design. Compared to PC based SDR, the SoC is also a better choice for portable and embedded scenario

An approach to achieve zero turnaround time in TDD operation on SDR front-end

Thanks to the digitization and softwarization of radio communication, the development cycle of new radio technologies can be significantly accelerated by prototyping on software-defined radio (SDR) platforms. However, a slow turnaround time (TT) of the front-end of an SDR for switching from receiving mode to transmitting mode or vice versa, are jeopardizing the prototyping of wireless protocols, standards, or systems with stringent latency requirements. In this paper, a novel solution called BaseBand processing unit operating in Half Duplex mode and analog Radio Frequency front-end operating in Full Duplex mode, BBHD-RFFD, is presented to reduce the TT on SDR. A prototype is realized on the widely adopted AD9361 radio frequency frontend to prove the validity of the proposed solution. Experiments unveil that for any type of application, the TT in time division duplex (TDD) operation mode can be reduced to zero by the BBHD-RFFD approach, with negligible impact on the communication system in terms of receiver sensitivity. The impact is measured for an in-house IEEE 802.15.4 compliant transceiver. When compared against the conventional TDD approach, only a 7.5-dB degradation is observed with the BBHD-RFFD approach. The measured sensitivity of -91 dBm is still well above the minimum level (i.e., -85 dBm at 2.4 GHz) defined by the IEEE 802.15.4 standard

SdrLift: A Domain-Specific Intermediate Hardware Synthesis Framework for Prototyping Software-Defined Radios

Modern design of Software-Defined Radio (SDR) applications is based on Field Programmable Gate Arrays (FPGA) due to their ability to be configured into solution architectures that are well suited to domain-specific problems while achieving the best trade-off between performance, power, area, and flexibility. FPGAs are well known for rich computational resources, which traditionally include logic, register, and routing resources. The increased technological advances have seen FPGAs incorporating more complex components that comprise sophisticated memory blocks, Digital Signal Processing (DSP) blocks, and high-speed interfacing to Gigabit Ethernet (GbE) and Peripheral Component Interconnect Express (PCIe) bus. Gateware for programming FPGAs is described at a lowlevel of design abstraction using Register Transfer Language (RTL), typically using either VHSIC-HDL (VHDL) or Verilog code. In practice, the low-level description languages have a very steep learning curve, provide low productivity for hardware designers and lack readily available open-source library support for fundamental designs, and consequently limit the design to only hardware experts. These limitations have led to the adoption of High-Level Synthesis (HLS) tools that raise design abstraction using syntax, semantics, and software development notations that are well-known to most software developers. However, while HLS has made programming of FPGAs more accessible and can increase the productivity of design, they are still not widely adopted in the design community due to the low-level skills that are still required to produce efficient designs. Additionally, the resultant RTL code from HLS tools is often difficult to decipher, modify and optimize due to the functionality and micro-architecture that are coupled together in a single High-Level Language (HLL). In order to alleviate these problems, Domain-Specific Languages (DSL) have been introduced to capture algorithms at a high level of abstraction with more expressive power and providing domain-specific optimizations that factor in new transformations and the trade-off between resource utilization and system performance. The problem of existing DSLs is that they are designed around imperative languages with an instruction sequence that does not match the hardware structure and intrinsics, leading to hardware designs with system properties that are unconformable to the high-level specifications and constraints. The aim of this thesis is, therefore, to design and implement an intermediatelevel framework namely SdrLift for use in high-level rapid prototyping of SDR applications that are based on an FPGA. The SdrLift input is a HLL developed using functional language constructs and design patterns that specify the structural behavior of the application design. The functionality of the SdrLift language is two-fold, first, it can be used directly by a designer to develop the SDR applications, secondly, it can be used as the Intermediate Representation (IR) step that is generated by a higher-level language or a DSL. The SdrLift compiler uses the dataflow graph as an IR to structurally represent the accelerator micro-architecture in which the components correspond to the fine-level and coarse-level Hardware blocks (HW Block) which are either auto-synthesized or integrated from existing reusable Intellectual Property (IP) core libraries. Another IR is in the form of a dataflow model and it is used for composition and global interconnection of the HW Blocks while making efficient interfacing decisions in an attempt to satisfy speed and resource usage objectives. Moreover, the dataflow model provides rules and properties that will be used to provide a theoretical framework that formally analyzes the characteristics of SDR applications (i.e. the throughput, sample rate, latency, and buffer size among other factors). Using both the directed graph flow (DFG) and the dataflow model in the SdrLift compiler provides two benefits: an abstraction of the microarchitecture from the high-level algorithm specifications and also decoupling of the microarchitecture from the low-level RTL implementation. Following the IR creation and model analyses is the VHDL code generation which employs the low-level optimizations that ensure optimal hardware design results. The code generation process per forms analysis to ensure the resultant hardware system conforms to the high-level design specifications and constraints. SdrLift is evaluated by developing representative SDR case studies, in which the VHDL code for eight different SDR applications is generated. The experimental results show that SdrLift achieves the desired performance and flexibility, while also conserving the hardware resources utilized

CMCVT : a concurrent multi-channel virtual transceiver

State-of-the-art wireless Gateways (GW) used in Internet of Things (IoT) offer a single channel radio link, which limits the capabilities of the IoT network controlled by the GW, as the GW can only use a single channel at a time to communicate with the end-device(s). The quality of service (e.g., aggregate throughput, latency) offered by a single channel GW could be substantially improved by employing a multi-channel transceiver, which is capable of transmitting/receiving data on different radio channels simultaneously, particularly for larger wireless networks. However, current solutions available in both research and commercial communities only offer multi-channel receiver capabilities, and do not incorporate the multi-channel transmitter part. In addition, in terms of implementation, these multi-channel receivers duplicate single-channel hardware functionality. In this paper, for the first time, a novel concurrent multi-channel virtual transceiver is introduced. The virtual transceiver offers multi-channel capabilities and uses the same single-hardware hardware implementation for the Physical (PHY) layer by employing the virtualization technique. This new virtual transceiver concept is demonstrated for an IEEE 802.15.4 based 8 x 8 channel transceiver, implemented on an Field Programmable Gate Array (FPGA) of a modern Software Defined Radio and is compared with the existing duplication approach. The duplication approach consumes 9008 LUTs, and 12120 FFs, whereas the proposed approach occupies only 2959 LUTs and 2105 FFs, saving 67.15% LUTs and 82.63% FFs in comparison with the duplication approach. The experimental results reveal that the virtual transceiver provides the same performance (e.g., receiver sensitivity of -98.5dBm) as the transceiver achieved by duplicating the PHY layers but consumes much less hardware resources. (C) 2020 The Authors. Published by Elsevier GmbH

Development and testing of the RHINO host streamed data acquisition framework

This project focuses on developing a supporting framework for integrating the Reconfigurable Hardware INterface for computing and radiO (RHINO) with a Personal Computer (PC) host in order to facilitate the development of Software Defined Radio (SDR) applications built using a hybrid RHINO/multicore PC system. The supporting framework that is the focus of this dissertation is designed around two main parts: a) resources for integrating the GNU Radio framework with the RHINO platform to allow data streams to be sent from RHINO to be processed by GNU Radio, and b) a concise and highly efficient C code module with accompanying Application Program Interface (API) that will receive streamed data from RHINO and provide data marshalling facilities to gather and dispatch blocks of data for further processing using C/C++ routines. The methodology followed in this research project involves investigating real-time streaming techniques using User Datagram Protocol (UDP) packets, furthermore, investigating how GNU Radio high-level SDR development framework can be integrated into the real-time data acquisition systems such as in the case of this project with RHINO. The literature for real-time processing requirements for the streamer framework was reviewed. The guidelines to implement a high performance, low latency and maximum throughput for streaming will consequently be presented and the proposed design motivated. The results achieved demonstrate an efficient data streaming system. The objectives of implementing RHINO data acquisition system through integration with standard C/C++ code and GNU Radio were satisfactorily met. The system was tested with real-time Radio Frequency (RF) demodulation. The system captures a pair of an In-phase/Quadrature signal (I/Q) sample at a time, which is one packet. The results show that data can be streamed from the RHINO board to GNU Radio over GbE with a minimum capturing latency of 10.2μs for 2 0 packet size and an average data capturing throughput of 0.54 Mega Bytes per second (MBps). The capturing latency, in this case, is the time taken from the time of the request to receiving the data. The FM receiver case study successfully demonstrated results of a demodulated FM signal of a 94.5 Mega Hetz (MHz) radio station. Further recommendations include making use of the 10GbE port on RHINO for data streaming purposes. 10GbE port on RHINO can be used together with GNU Radio to improve the speed of the RHINO streamer

Design and Performance Analysis of Hardware Realization of 3GPP Physical Layer for 5G Cell Search

5G Cell Search (CS) is the first step for user equipment (UE) to initiate the communication with the 5G node B (gNB) every time it is powered ON. In cellular networks, CS is accomplished via synchronization signals (SS) broadcasted by gNB. 5G 3rd generation partnership project (3GPP) specifications offer a detailed discussion on the SS generation at gNB but a limited understanding of their blind search, and detection is available. Unlike 4G, 5G SS may not be transmitted at the center of carrier frequency and their frequency location is unknown to UE. In this work, we demonstrate the 5G CS by designing 3GPP compatible hardware realization of the physical layer (PHY) of the gNB transmitter and UE receiver. The proposed SS detection explores a novel down-sampling approach resulting in a significant reduction in complexity and latency. Via detailed performance analysis, we analyze the functional correctness, computational complexity, and latency of the proposed approach for different word lengths, signal-to-noise ratio (SNR), and down-sampling factors. We demonstrate the complete CS functionality on GNU Radio-based RFNoC framework and USRP-FPGA platform. The 3GPP compatibility and demonstration on hardware strengthen the commercial significance of the proposed work

IoT protocols, architectures, and applications

The proliferation of embedded systems, wireless technologies, and Internet protocols have made it possible for the Internet-of-things (IoT) to bridge the gap between the physical and the virtual world and thereby enabling monitoring and control of the physical environment by data processing systems. IoT refers to the inter-networking of everyday objects that are equipped with sensing, computing, and communication capabilities. These networks can collaborate to autonomously solve a variety of tasks. Due to the very diverse set of applications and application requirements, there is no single communication technology that is able to provide cost-effective and close to optimal performance in all scenarios. In this chapter, we report on research carried out on a selected number of IoT topics: low-power wide-area networks, in particular, LoRa and narrow-band IoT (NB-IoT); IP version 6 over IEEE 802.15.4 time-slotted channel hopping (6TiSCH); vehicular antenna design, integration, and processing; security aspects for vehicular networks; energy efficiency and harvesting for IoT systems; and software-defined networking/network functions virtualization for (SDN/NFV) IoT

Cross-Layer Rapid Prototyping and Synthesis of Application-Specific and Reconfigurable Many-accelerator Platforms

Technological advances of recent years laid the foundation consolidation of informatisationof society, impacting on economic, political, cultural and socialdimensions. At the peak of this realization, today, more and more everydaydevices are connected to the web, giving the term ”Internet of Things”. The futureholds the full connection and interaction of IT and communications systemsto the natural world, delimiting the transition to natural cyber systems and offeringmeta-services in the physical world, such as personalized medical care, autonomoustransportation, smart energy cities etc. . Outlining the necessities of this dynamicallyevolving market, computer engineers are required to implement computingplatforms that incorporate both increased systemic complexity and also cover awide range of meta-characteristics, such as the cost and design time, reliabilityand reuse, which are prescribed by a conflicting set of functional, technical andconstruction constraints. This thesis aims to address these design challenges bydeveloping methodologies and hardware/software co-design tools that enable therapid implementation and efficient synthesis of architectural solutions, which specifyoperating meta-features required by the modern market. Specifically, this thesispresents a) methodologies to accelerate the design flow for both reconfigurableand application-specific architectures, b) coarse-grain heterogeneous architecturaltemplates for processing and communication acceleration and c) efficient multiobjectivesynthesis techniques both at high abstraction level of programming andphysical silicon level.Regarding to the acceleration of the design flow, the proposed methodologyemploys virtual platforms in order to hide architectural details and drastically reducesimulation time. An extension of this framework introduces the systemicco-simulation using reconfigurable acceleration platforms as co-emulation intermediateplatforms. Thus, the development cycle of a hardware/software productis accelerated by moving from a vertical serial flow to a circular interactive loop.Moreover the simulation capabilities are enriched with efficient detection and correctiontechniques of design errors, as well as control methods of performancemetrics of the system according to the desired specifications, during all phasesof the system development. In orthogonal correlation with the aforementionedmethodological framework, a new architectural template is proposed, aiming atbridging the gap between design complexity and technological productivity usingspecialized hardware accelerators in heterogeneous systems-on-chip and networkon-chip platforms. It is presented a novel co-design methodology for the hardwareaccelerators and their respective programming software, including the tasks allocationto the available resources of the system/network. The introduced frameworkprovides implementation techniques for the accelerators, using either conventionalprogramming flows with hardware description language or abstract programmingmodel flows, using techniques from high-level synthesis. In any case, it is providedthe option of systemic measures optimization, such as the processing speed,the throughput, the reliability, the power consumption and the design silicon area.Finally, on addressing the increased complexity in design tools of reconfigurablesystems, there are proposed novel multi-objective optimization evolutionary algo-rithms which exploit the modern multicore processors and the coarse-grain natureof multithreaded programming environments (e.g. OpenMP) in order to reduce theplacement time, while by simultaneously grouping the applications based on theirintrinsic characteristics, the effectively explore the design space effectively.The efficiency of the proposed architectural templates, design tools and methodologyflows is evaluated in relation to the existing edge solutions with applicationsfrom typical computing domains, such as digital signal processing, multimedia andarithmetic complexity, as well as from systemic heterogeneous environments, suchas a computer vision system for autonomous robotic space navigation and manyacceleratorsystems for HPC and workstations/datacenters. The results strengthenthe belief of the author, that this thesis provides competitive expertise to addresscomplex modern - and projected future - design challenges.Οι τεχνολογικές εξελίξεις των τελευταίων ετών έθεσαν τα θεμέλια εδραίωσης της πληροφοριοποίησης της κοινωνίας, επιδρώντας σε οικονομικές,πολιτικές, πολιτιστικές και κοινωνικές διαστάσεις. Στο απόγειο αυτής τη ςπραγμάτωσης, σήμερα, ολοένα και περισσότερες καθημερινές συσκευές συνδέονται στο παγκόσμιο ιστό, αποδίδοντας τον όρο «Ίντερνετ των πραγμάτων».Το μέλλον επιφυλάσσει την πλήρη σύνδεση και αλληλεπίδραση των συστημάτων πληροφορικής και επικοινωνιών με τον φυσικό κόσμο, οριοθετώντας τη μετάβαση στα συστήματα φυσικού κυβερνοχώρου και προσφέροντας μεταυπηρεσίες στον φυσικό κόσμο όπως προσωποποιημένη ιατρική περίθαλψη, αυτόνομες μετακινήσεις, έξυπνες ενεργειακά πόλεις κ.α. . Σκιαγραφώντας τις ανάγκες αυτής της δυναμικά εξελισσόμενης αγοράς, οι μηχανικοί υπολογιστών καλούνται να υλοποιήσουν υπολογιστικές πλατφόρμες που αφενός ενσωματώνουν αυξημένη συστημική πολυπλοκότητα και αφετέρου καλύπτουν ένα ευρύ φάσμα μεταχαρακτηριστικών, όπως λ.χ. το κόστος σχεδιασμού, ο χρόνος σχεδιασμού, η αξιοπιστία και η επαναχρησιμοποίηση, τα οποία προδιαγράφονται από ένα αντικρουόμενο σύνολο λειτουργικών, τεχνολογικών και κατασκευαστικών περιορισμών. Η παρούσα διατριβή στοχεύει στην αντιμετώπιση των παραπάνω σχεδιαστικών προκλήσεων, μέσω της ανάπτυξης μεθοδολογιών και εργαλείων συνσχεδίασης υλικού/λογισμικού που επιτρέπουν την ταχεία υλοποίηση καθώς και την αποδοτική σύνθεση αρχιτεκτονικών λύσεων, οι οποίες προδιαγράφουν τα μετα-χαρακτηριστικά λειτουργίας που απαιτεί η σύγχρονη αγορά. Συγκεκριμένα, στα πλαίσια αυτής της διατριβής, παρουσιάζονται α) μεθοδολογίες επιτάχυνσης της ροής σχεδιασμού τόσο για επαναδιαμορφούμενες όσο και για εξειδικευμένες αρχιτεκτονικές, β) ετερογενή αδρομερή αρχιτεκτονικά πρότυπα επιτάχυνσης επεξεργασίας και επικοινωνίας και γ) αποδοτικές τεχνικές πολυκριτηριακής σύνθεσης τόσο σε υψηλό αφαιρετικό επίπεδο προγραμματισμού,όσο και σε φυσικό επίπεδο πυριτίου.Αναφορικά προς την επιτάχυνση της ροής σχεδιασμού, προτείνεται μια μεθοδολογία που χρησιμοποιεί εικονικές πλατφόρμες, οι οποίες αφαιρώντας τις αρχιτεκτονικές λεπτομέρειες καταφέρνουν να μειώσουν σημαντικά το χρόνο εξομοίωσης. Παράλληλα, εισηγείται η συστημική συν-εξομοίωση με τη χρήση επαναδιαμορφούμενων πλατφορμών, ως μέσων επιτάχυνσης. Με αυτόν τον τρόπο, ο κύκλος ανάπτυξης ενός προϊόντος υλικού, μετατεθειμένος από την κάθετη σειριακή ροή σε έναν κυκλικό αλληλεπιδραστικό βρόγχο, καθίσταται ταχύτερος, ενώ οι δυνατότητες προσομοίωσης εμπλουτίζονται με αποδοτικότερες μεθόδους εντοπισμού και διόρθωσης σχεδιαστικών σφαλμάτων, καθώς και μεθόδους ελέγχου των μετρικών απόδοσης του συστήματος σε σχέση με τις επιθυμητές προδιαγραφές, σε όλες τις φάσεις ανάπτυξης του συστήματος. Σε ορθογώνια συνάφεια με το προαναφερθέν μεθοδολογικό πλαίσιο, προτείνονται νέα αρχιτεκτονικά πρότυπα που στοχεύουν στη γεφύρωση του χάσματος μεταξύ της σχεδιαστικής πολυπλοκότητας και της τεχνολογικής παραγωγικότητας, με τη χρήση συστημάτων εξειδικευμένων επιταχυντών υλικού σε ετερογενή συστήματα-σε-ψηφίδα καθώς και δίκτυα-σε-ψηφίδα. Παρουσιάζεται κατάλληλη μεθοδολογία συν-σχεδίασης των επιταχυντών υλικού και του λογισμικού προκειμένου να αποφασισθεί η κατανομή των εργασιών στους διαθέσιμους πόρους του συστήματος/δικτύου. Το μεθοδολογικό πλαίσιο προβλέπει την υλοποίηση των επιταχυντών είτε με συμβατικές μεθόδους προγραμματισμού σε γλώσσα περιγραφής υλικού είτε με αφαιρετικό προγραμματιστικό μοντέλο με τη χρήση τεχνικών υψηλού επιπέδου σύνθεσης. Σε κάθε περίπτωση, δίδεται η δυνατότητα στο σχεδιαστή για βελτιστοποίηση συστημικών μετρικών, όπως η ταχύτητα επεξεργασίας, η ρυθμαπόδοση, η αξιοπιστία, η κατανάλωση ενέργειας και η επιφάνεια πυριτίου του σχεδιασμού. Τέλος, προκειμένου να αντιμετωπισθεί η αυξημένη πολυπλοκότητα στα σχεδιαστικά εργαλεία επαναδιαμορφούμενων συστημάτων, προτείνονται νέοι εξελικτικοί αλγόριθμοι πολυκριτηριακής βελτιστοποίησης, οι οποίοι εκμεταλλευόμενοι τους σύγχρονους πολυπύρηνους επεξεργαστές και την αδρομερή φύση των πολυνηματικών περιβαλλόντων προγραμματισμού (π.χ. OpenMP), μειώνουν το χρόνο επίλυσης του προβλήματος της τοποθέτησης των λογικών πόρων σε φυσικούς,ενώ ταυτόχρονα, ομαδοποιώντας τις εφαρμογές βάση των εγγενών χαρακτηριστικών τους, διερευνούν αποτελεσματικότερα το χώρο σχεδίασης.Η αποδοτικότητά των προτεινόμενων αρχιτεκτονικών προτύπων και μεθοδολογιών επαληθεύτηκε σε σχέση με τις υφιστάμενες λύσεις αιχμής τόσο σε αυτοτελής εφαρμογές, όπως η ψηφιακή επεξεργασία σήματος, τα πολυμέσα και τα προβλήματα αριθμητικής πολυπλοκότητας, καθώς και σε συστημικά ετερογενή περιβάλλοντα, όπως ένα σύστημα όρασης υπολογιστών για αυτόνομα διαστημικά ρομποτικά οχήματα και ένα σύστημα πολλαπλών επιταχυντών υλικού για σταθμούς εργασίας και κέντρα δεδομένων, στοχεύοντας εφαρμογές υψηλής υπολογιστικής απόδοσης (HPC). Τα αποτελέσματα ενισχύουν την πεποίθηση του γράφοντα, ότι η παρούσα διατριβή παρέχει ανταγωνιστική τεχνογνωσία για την αντιμετώπιση των πολύπλοκων σύγχρονων και προβλεπόμενα μελλοντικών σχεδιαστικών προκλήσεων