PERFORMANCE ANALYSIS AND OPTIMIZATION OF 10 NM TG N- AND P-CHANNEL SOI FINFETS FOR CIRCUIT APPLICATIONS

This paper analyses the electrical characteristics of 10 nm tri-gate (TG) N- and P-channel silicon-on-insulator (SOI) FinFETs with hafnium oxide gate dielectric. The analysis has been performed through simulations by using Silvaco ATLAS TCAD with the Bohm quantum potential (BQP) algorithm. The influence of the geometrical parameters on the threshold voltage VTH, the subthreshold swing (SS), the transconductance and the on/off current ratio, ION/IOFF, is investigated. The two structures have been optimized for CMOS inverter implementation. The simulation results show that the N-FinFET and the P-FinFET can reach a minimum SS value with Fin heights of 15 nm and 9 nm, respectively. In addition, low threshold voltages of 0.61 V and 0.27 V for N- and P-channel SOI FinFETs, respectively, are obtained at a Fin width of 7 nm

Design, Modeling and Analysis of Non-classical Field Effect Transistors

Transistor scaling following per Moore\u27s Law slows down its pace when entering into nanometer regime where short channel effects (SCEs), including threshold voltage fluctuation, increased leakage current and mobility degradation, become pronounced in the traditional planar silicon MOSFET. In addition, as the demand of diversified functionalities rises, conventional silicon technologies cannot satisfy all non-digital applications requirements because of restrictions that stem from the fundamental material properties. Therefore, novel device materials and structures are desirable to fuel further evolution of semiconductor technologies. In this dissertation, I have proposed innovative device structures and addressed design considerations of those non-classical field effect transistors for digital, analog/RF and power applications with projected benefits. Considering device process difficulties and the dramatic fabrication cost, application-oriented device design and optimization are performed through device physics analysis and TCAD modeling methodology to develop design guidelines utilizing transistor\u27s improved characteristics toward application-specific circuit performance enhancement. Results support proposed device design methodologies that will allow development of novel transistors capable of overcoming limitation of planar nanoscale MOSFETs. In this work, both silicon and III-V compound devices are designed, optimized and characterized for digital and non-digital applications through calibrated 2-D and 3-D TCAD simulation. For digital functionalities, silicon and InGaAs MOSFETs have been investigated. Optimized 3-D silicon-on-insulator (SOI) and body-on-insulator (BOI) FinFETs are simulated to demonstrate their impact on the performance of volatile memory SRAM module with consideration of self-heating effects. Comprehensive simulation results suggest that the current drivability degradation due to increased device temperature is modest for both devices and corresponding digital circuits. However, SOI FinFET is recommended for the design of low voltage operation digital modules because of its faster AC response and better SCEs management than the BOI structure. The FinFET concept is also applied to the non-volatile memory cell at 22 nm technology node for low voltage operation with suppressed SCEs. In addition to the silicon technology, our TCAD estimation based on upper projections show that the InGaAs FinFET, with superior mobility and improved interface conditions, achieve tremendous drive current boost and aggressively suppressed SCEs and thereby a strong contender for low-power high-performance applications over the silicon counterpart. For non-digital functionalities, multi-fin FETs and GaN HEMT have been studied. Mixed-mode simulations along with developed optimization guidelines establish the realistic application potential of underlap design of silicon multi-Fin FETs for analog/RF operation. The device with underlap design shows compromised current drivability but improve analog intrinsic gain and high frequency performance. To investigate the potential of the novel N-polar GaN material, for the first time, I have provided calibrated TCAD modeling of E-mode N-polar GaN single-channel HEMT. In this work, I have also proposed a novel E-mode dual-channel hybrid MIS-HEMT showing greatly enhanced current carrying capability. The impact of GaN layer scaling has been investigated through extensive TCAD simulations and demonstrated techniques for device optimization

Characterisation of thermal and coupling effects in advanced silicon MOSFETs

PhD ThesisNew approaches to metal-oxide-semiconductor field effect transistor (MOSFET) engineering emerge in order to keep up with the electronics market demands. Two main candidates for the next few generations of Moore’s law are planar ultra-thin body and buried oxide (UTBB) devices and three-dimensional FinFETs. Due to miniature dimensions and new materials with low thermal conductivity, performance of advanced MOSFETs is affected by self-heating and substrate effects. Self-heating results in an increase of the device temperature which causes mobility reduction, compromised reliability and signal delays. The substrate effect is a parasitic source and drain coupling which leads to frequency-dependent analogue behaviour. Both effects manifest themselves in the output conductance variation with frequency and impact analogue as well as digital performance. In this thesis self-heating and substrate effects in FinFETs and UTBB devices are characterised, discussed and compared. The results are used to identify trade-offs in device performance, geometry and thermal properties. Methods how to optimise the device geometry or biasing conditions in order to minimise the parasitic effects are suggested. To identify the most suitable technique for self-heating characterisation in advanced semiconductor devices, different methods of thermal characterisation (time and frequency domain) were experimentally compared and evaluated alongside an analytical model. RF and two different pulsed I-V techniques were initially applied to partially depleted silicon-on-insulator (PDSOI) devices. The pulsed I-V hot chuck method showed good agreement with the RF technique in the PDSOI devices. However, subsequent analysis demonstrated that for more advanced technologies the time domain methods can underestimate self-heating. This is due to the reduction of the thermal time constants into the nanosecond range and limitations of the pulsed I-V set-up. The reduction is related to the major increase of the surface to volume ratio in advanced MOSFETs. Consequently the work showed that the thermal properties of advanced semiconductor devices must be characterised within the frequency domain. For UTBB devices with 7-8 nm Si body and 10 nm ultra-thin buried oxide (BOX) the analogue performance degradation caused by the substrate effects can be stronger than the analogue performance degradation caused by self-heating. However, the substrate effects can be effectively reduced if the substrate doping beneath the buried ii oxide is adjusted using a ground plane. In the MHz – GHz frequency range the intrinsic voltage gain variation is reduced ~6 times when a device is biased in saturation if a ground plane is implemented compared with a device without a ground plane. UTBB devices with 25 nm BOX were compared with UTBB devices with 10 nm BOX. It was found that the buried oxide thinning from 25 nm to 10 nm is not critical from the thermal point of view as other heat evacuation paths (e.g. source and drain) start to play a role. Thermal and substrate effects in FinFETs were also analysed. It was experimentally shown that FinFET thermal properties depend on the device geometry. The thermal resistance of FinFETs strongly varies with the fin width and number of parallel fins, whereas the fin spacing is less critical. The results suggest that there are trade-offs between thermal properties and integration density, electrostatic control and design complexity, since these aspects depend on device geometry. The high frequency substrate effects were found to be effectively reduced in devices with sub-100 nm wide fins.Engineering and Physical Sciences Research Council (EPSRC) and EU fundin

Thermal stability analysis and performance exploration of asymmetrical dual-k underlap spacer (ADKUS) SOI FinFET for high performance circuit applications

This paper explores the performance of asymmetrical dual-k underlap spacer (ADKUS) SOI FinFET (device-D1) over the wide temperature range (200 K-450 K). An attempt has been made to find out the zero temperature coefficient (ZTC) biased point to enhance the digital, analog and RF performance at 20 nm channel length. The proposed device will be suitable for VLSI circuit’s design, internet of things (IoT) interfacing components and algorithm development for security applications of information technology. The potential parameters of device-D1 like intrinsic gain (AV ), output conductance (gd ), transconductance (gm ), early voltage (VEA ), off current (Ioff) , on current (Ion), Ion/Ioff ratio, gate to source capacitance (Cgs), gate to drain capacitance (Cgd), cut-off frequency (fT), energy (CV2), intrinsic delay (CV/I), energy-delay product (EDP), power dissipation (PD), sub-threshold slope (SS), Q-Factor (gm,max/SS), threshold voltage (Vth) and maximum trans-conductance (gm,max) are subjected to analyze for evaluating the performance of ADKUS SOI FinFET for wide temperature environment. The validation of a temperature based performance of ADKUS SOI FinFET gives an opportunity to design the numerous analog and digital components of internet security infrastructure at wide temperature environment. These ADKUS SOI FinFET based components give new technology to the IoT which has the ability to connect the real world with the digital world and enables the people and machines to know the status of thousands of components simultaneously

Digital and analog TFET circuits: Design and benchmark

In this work, we investigate by means of simulations the performance of basic digital, analog, and mixed-signal circuits employing tunnel-FETs (TFETs). The analysis reviews and complements our previous papers on these topics. By considering the same devices for all the analysis, we are able to draw consistent conclusions for a wide variety of circuits. A virtual complementary TFET technology consisting of III-V heterojunction nanowires is considered. Technology Computer Aided Design (TCAD) models are calibrated against the results of advanced full-quantum simulation tools and then used to generate look-up-tables suited for circuit simulations. The virtual complementary TFET technology is benchmarked against predictive technology models (PTM) of complementary silicon FinFETs for the 10 nm node over a wide range of supply voltages (VDD) in the sub-threshold voltage domain considering the same footprint between the vertical TFETs and the lateral FinFETs and the same static power. In spite of the asymmetry between p- and n-type transistors, the results show clear advantages of TFET technology over FinFET for VDDlower than 0.4 V. Moreover, we highlight how differences in the I-V characteristics of FinFETs and TFETs suggest to adapt the circuit topologies used to implement basic digital and analog blocks with respect to the most common CMOS solutions

Digital and analog TFET circuits: Design and benchmark

In this work, we investigate by means of simulations the performance of basic digital, analog, and mixed-signal circuits employing tunnel-FETs (TFETs). The analysis reviews and complements our previous papers on these topics. By considering the same devices for all the analysis, we are able to draw consistent conclusions for a wide variety of circuits. A virtual complementary TFET technology consisting of III-V heterojunction nanowires is considered. Technology Computer Aided Design (TCAD) models are calibrated against the results of advanced full-quantum simulation tools and then used to generate look-up-tables suited for circuit simulations. The virtual complementary TFET technology is benchmarked against predictive technology models (PTM) of complementary silicon FinFETs for the 10 nm node over a wide range of supply voltages (VDD) in the sub-threshold voltage domain considering the same footprint between the vertical TFETs and the lateral FinFETs and the same static power. In spite of the asymmetry between p- and n-type transistors, the results show clear advantages of TFET technology over FinFET for VDDlower than 0.4 V. Moreover, we highlight how differences in the I-V characteristics of FinFETs and TFETs suggest to adapt the circuit topologies used to implement basic digital and analog blocks with respect to the most common CMOS solutions

Analog circuits using FinFETs: benefits in speed-accuracy-power trade-off and simulation of parasitic effects

Multi-gate FET, e.g. FinFET devices are the most promising contenders to replace bulk FETs in sub-45 nm CMOS technologies due to their improved sub threshold and short channel behavior, associated with low leakage currents. The introduction of novel gate stack materials (e.g. metal gate, high-k dielectric) and modified device architectures (e.g. fully depleted, undoped fins) affect the analog device properties significantly. First measurements indicate enhanced intrinsic gain (<i>g<sub>m</sub>/g<sub>DS</sub></i>) and promising matching behavior of FinFETs. The resulting benefits regarding the speed-accuracy-power trade-off in analog circuit design will be shown in this work. Additionally novel device specific effects will be discussed. The hysteresis effect caused by charge trapping in high-k dielectrics or self-heating due to the high thermal resistor of the BOX isolation are possible challenges for analog design in these emerging technologies. To gain an early assessment of the impact of such parasitic effects SPICE based models are derived and applied in analog building blocks

INFLUENCE OF OXIDE THICKNESS VARIATION ON ANALOG AND RF PERFORMANCES OF SOI FINFET

This paper focuses on the impact of variation in the thickness of the oxide (SiO2) layer on the performance parameters of a FinFET analysed by varying the oxide layer thickness in the range of 0.8nm to 3nm. While varying the oxide layer thickness, the overall width of the FinFET is fixed at a value 30nm, and the FinFET parameters are analysed for structures with different oxide layer thickness. The parameters like drain current, transconductance, transconductance generation factor, parasitic capacitances, output conductance, cut-off frequency, maximum frequency, GBW, energy and power consumption are calculated to study the influence of FinFET oxide (SiO2) layer thickness variation. It is detected from the result and analysis that the drain current, transconductance, transconductance generation factor, gain bandwidth and output conductance improve with decrement in oxide layer thickness whereas, the parasitic capacitances, cut-off frequency and maximum frequency degrade when there is a reduction in oxide (SiO2) layer thickness. The parameters like energy and consumed power of FinFET get better when the oxide (SiO2) layer thickness increases