3,191 research outputs found
IETF standardization in the field of the Internet of Things (IoT): a survey
Smart embedded objects will become an important part of what is called the Internet of Things. However, the integration of embedded devices into the Internet introduces several challenges, since many of the existing Internet technologies and protocols were not designed for this class of devices. In the past few years, there have been many efforts to enable the extension of Internet technologies to constrained devices. Initially, this resulted in proprietary protocols and architectures. Later, the integration of constrained devices into the Internet was embraced by IETF, moving towards standardized IP-based protocols. In this paper, we will briefly review the history of integrating constrained devices into the Internet, followed by an extensive overview of IETF standardization work in the 6LoWPAN, ROLL and CoRE working groups. This is complemented with a broad overview of related research results that illustrate how this work can be extended or used to tackle other problems and with a discussion on open issues and challenges. As such the aim of this paper is twofold: apart from giving readers solid insights in IETF standardization work on the Internet of Things, it also aims to encourage readers to further explore the world of Internet-connected objects, pointing to future research opportunities
MONICA in Hamburg: Towards Large-Scale IoT Deployments in a Smart City
Modern cities and metropolitan areas all over the world face new management
challenges in the 21st century primarily due to increasing demands on living
standards by the urban population. These challenges range from climate change,
pollution, transportation, and citizen engagement, to urban planning, and
security threats. The primary goal of a Smart City is to counteract these
problems and mitigate their effects by means of modern ICT to improve urban
administration and infrastructure. Key ideas are to utilise network
communication to inter-connect public authorities; but also to deploy and
integrate numerous sensors and actuators throughout the city infrastructure -
which is also widely known as the Internet of Things (IoT). Thus, IoT
technologies will be an integral part and key enabler to achieve many
objectives of the Smart City vision.
The contributions of this paper are as follows. We first examine a number of
IoT platforms, technologies and network standards that can help to foster a
Smart City environment. Second, we introduce the EU project MONICA which aims
for demonstration of large-scale IoT deployments at public, inner-city events
and give an overview on its IoT platform architecture. And third, we provide a
case-study report on SmartCity activities by the City of Hamburg and provide
insights on recent (on-going) field tests of a vertically integrated,
end-to-end IoT sensor application.Comment: 6 page
Evolving SDN for Low-Power IoT Networks
Software Defined Networking (SDN) offers a flexible and scalable architecture
that abstracts decision making away from individual devices and provides a
programmable network platform. However, implementing a centralized SDN
architecture within the constraints of a low-power wireless network faces
considerable challenges. Not only is controller traffic subject to jitter due
to unreliable links and network contention, but the overhead generated by SDN
can severely affect the performance of other traffic. This paper addresses the
challenge of bringing high-overhead SDN architecture to IEEE 802.15.4 networks.
We explore how traditional SDN needs to evolve in order to overcome the
constraints of low-power wireless networks, and discuss protocol and
architectural optimizations necessary to reduce SDN control overhead - the main
barrier to successful implementation. We argue that interoperability with the
existing protocol stack is necessary to provide a platform for controller
discovery and coexistence with legacy networks. We consequently introduce
{\mu}SDN, a lightweight SDN framework for Contiki, with both IPv6 and
underlying routing protocol interoperability, as well as optimizing a number of
elements within the SDN architecture to reduce control overhead to practical
levels. We evaluate {\mu}SDN in terms of latency, energy, and packet delivery.
Through this evaluation we show how the cost of SDN control overhead (both
bootstrapping and management) can be reduced to a point where comparable
performance and scalability is achieved against an IEEE 802.15.4-2012 RPL-based
network. Additionally, we demonstrate {\mu}SDN through simulation: providing a
use-case where the SDN configurability can be used to provide Quality of
Service (QoS) for critical network flows experiencing interference, and we
achieve considerable reductions in delay and jitter in comparison to a scenario
without SDN
Information Centric Networking in the IoT: Experiments with NDN in the Wild
This paper explores the feasibility, advantages, and challenges of an
ICN-based approach in the Internet of Things. We report on the first NDN
experiments in a life-size IoT deployment, spread over tens of rooms on several
floors of a building. Based on the insights gained with these experiments, the
paper analyses the shortcomings of CCN applied to IoT. Several interoperable
CCN enhancements are then proposed and evaluated. We significantly decreased
control traffic (i.e., interest messages) and leverage data path and caching to
match IoT requirements in terms of energy and bandwidth constraints. Our
optimizations increase content availability in case of IoT nodes with
intermittent activity. This paper also provides the first experimental
comparison of CCN with the common IoT standards 6LoWPAN/RPL/UDP.Comment: 10 pages, 10 figures and tables, ACM ICN-2014 conferenc
A Test Bed for Evaluating the Performance of IoT Networks
The use of smaller, personal IoT networks has increased over the past several years. These devices demand a lot of resources but only have limited access. To establish and sustain a flexible network connection, 6LoWPAN with RPL protocol is commonly used. While RPL provides a low-cost solution for connection, it lacks load balancing mechanisms. Improvements in OF load balancing can be implemented to strengthen network stability. This paper proposes a test bed configuration to show the toll of frequent parent switching on 6LoWPAN. Contiki’s RPL 6LoWPAN software runs on STM32 Nucleo microcontrollers with expansion boards for this test bed. The configuration tests frequency of parent changes and packet loss to demonstrate network instability of different RPL OFs. Tests on MRHOF for RPL were executed to confirm the working configuration. Results, with troubleshooting and improvements, show a working bed. The laid-out configuration provides a means for testing network stability in IoT networks
- …