A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

A 60-Gb/s PAM4 Wireline Receiver With 2-Tap Direct Decision Feedback Equalization Employing Track-and-Regenerate Slicers in 28-nm CMOS

This article describes a 4-level pulse amplitude modulation (PAM4) receiver incorporating continuous time linear equalizers (CTLEs) and a 2-tap direct decision feedback equalizer (DFE) for applications in wireline communication. A CMOS track-and-regenerate slicer is proposed and employed in the PAM4 receiver. The proposed slicer is designed for the purposes of improving the clock-to-Q delay as well as the output signal swing. A direct DFE in a PAM4 receiver is made possible with the proposed slicer by having rail-to-rail digital feedback signals available with reduced delay, and accordingly relaxing the settling time constraint of the summer. With the 2-tap direct DFE enabled by the proposed slicer, loop-unrolling and inductor-based bandwidth enhancement techniques, which can be area/power intensive, are not necessary at high data rates. The PAM4 receiver fabricated in 28-nm CMOS technology achieves bit-error-rate (BER) better than 1E-12, and energy efficiency of 1.1 pJ/b at 60 Gb/s, measured over a channel with 8.2-dB loss at Nyquist

오프셋 제거기의 적응 제어 등화기와 보우-레이트 위상 검출기를 활용한 수신기 설계

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2021.8. 염제완.In this thesis, designs of high-speed, low-power wireline receivers (RX) are explained. To be specific, the circuit techniques of DC offset cancellation, merged-summer DFE, stochastic Baud-rate CDR, and the phase detector (PD) for multi-level signal are proposed. At first, an RX with adaptive offset cancellation (AOC) and merged summer decision-feedback equalizer (DFE) is proposed. The proposed AOC engine removes the random DC offset of the data path by examining the random data stream's sampled data and edge outputs. In addition, the proposed RX incorporates a shared-summer DFE in a half-rate structure to reduce power dissipation and hardware complexity of the adaptive equalizer. A prototype chip fabricated in 40 nm CMOS technology occupies an active area of 0.083 mm2. Thanks to the AOC engine, the proposed RX achieves the BER of less than 10-12 in a wide range of data rates: 1.62-10 Gb/s. The proposed RX consumes 18.6 mW at 10 Gb/s over a channel with a 27 dB loss at 5 GHz, exhibiting a figure-of-merit of 0.068 pJ/b/dB. Secondly, a 40 nm CMOS RX with Baud-rate phase-detector (BRPD) is proposed. The RX includes two PDs: the BRPD employing the stochastic technique and the BRPD suitable for multi-level signals. Thanks to the Baud-rate CDR’s advantage, by not using an edge-sampling clock, the proposed CDR can reduce the power consumption by lowering the hardware complexity. Besides, the proposed stochastic phase detector (SPD) tracks an optimal phase-locking point that maximizes the vertical eye opening. Furthermore, despite residual inter-symbol interference, proposed BRPD for multi-level signal secures vertical eye margin, which is especially vulnerable in the multi-level signal. Besides, the proposed BRPD has a unique lock point with an adaptive DFE, unlike conventional Mueller-Muller PD. A prototype chip fabricated in 40 nm CMOS technology occupies an active area of 0.24 mm2. The proposed PAM-4 RX achieves the bit-error-rate less than 10-11 in 48 Gb/s and the power efficiency of 2.42 pJ/b.본 논문은 고속, 저전력으로 동작하는 유선 수신기의 설계에 대해 설명하고 있다. 구체적으로 말하면, 오프셋 상쇄, 병합된 서머를 사용하는 결정 피드백 등화기 기술, 확률적 보우 레이트 클럭과 데이터 복원기, 그리고 다중 레벨 신호에 적합한 위상 검출기를 제안한다. 첫째로, 적응 오프셋 제거 및 병합된 서머를 사용하는 결정 피드백 등화기를 갖춘 수신기를 제안한다. 제안된 적응 오프셋 제거 엔진은 임의의 데이터 스트림의 샘플링 데이터, 에지 출력을 검사하여 데이터 경로 상의 오프셋을 제거한다. 또한 하프 레이트 구조의 병합된 서머를 사용하는 결정 피드백 등화기는 전력의 사용과 하드웨어의 복잡성을 줄인다. 40 nm CMOS 기술로 제작된 프로토타입 칩은 0.083 mm2 의 면적을 가진다. 적응 오프셋 제거기 덕분에 제안된 수신기는 10-12 미만의 BER을 달성한다. 또한 제안된 수신기는 5GHz에서 27 dB의 로스를 갖는 채널에서 10 Gb/s의 속도에서 18.6 mW를 소비하며 0.068 pJ/b/dB의 FoM을 달성하였다. 두번째로, 보우 레이트 위상 검출기가 있는 40 nm CMOS 수신기가 제안되었다. 수신기에는 두개의 보우 레이트 위상 검출기를 포함한다. 하나는 확률론적 기법을 사용하는 보우 레이트 위상 검출기이다. 보우 레이트 클럭 데이터 복원기의 장점 덕분에 에지 샘플링 클럭을 사용하지 않음으로서 파워의 소모와 하드웨어의 복잡성을 줄였다. 또한 확률적 위상 검출기는 수직 아이 오프닝을 최대화하는 최적의 위상 지점을 찾을 수 있었다. 다른 위상 검출기는 다중 레벨 신호에 적합한 방식이다. 심볼 간 간섭이 다중 레벨 신호에 매우 취약한 문제가 있더라도 제안된 다중 레벨 신호용 보우 레이트 위상 검출기는 수직 아이 마진을 확보한다. 게다가 제안된 보우 레이트 위상 검출기는 기존의 뮬러-뮐러 위상 검출기와 달리 적응형 결정 피드백 등화기가 있더라도 유일한 락 지점을 갖는다. 프로토타입 칩은 0.24mm2의 면적을 가진다. 제안된 PAM-4 수신기는 48 Gb/s의 속도에서 10-11 미만의 BER을 가지고, 2.42 pJ/b의 FoM을 가진다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 BACKGROUNDS 6 2.1 BASIC ARCHITECTURE IN SERIAL LINK 6 2.1.1 SERIAL COMMUNICATION 6 2.1.2 CLOCK AND DATA RECOVERY 8 2.1.3 MULTI-LEVEL PULSE-AMPLITUDE MODULATION 10 2.2 EQUALIZER 12 2.2.1 EQUALIZER OVERVIEW 12 2.2.2 DECISION-FEEDBACK EQUALIZER 15 2.2.3 ADAPTIVE EQUALIZER 18 2.3 CLOCK RECOVERY 21 2.3.1 2X OVERSAMPLING PD ALEXANDER PD 22 2.3.2 BAUD-RATE PD MUELLER MULLER PD 25 CHAPTER 3 AN ADAPTIVE OFFSET CANCELLATION SCHEME AND SHARED SUMMER ADAPTIVE DFE 28 3.1 OVERVIEW 28 3.2 AN ADAPTIVE OFFSET CANCELLATION SCHEME AND SHARED-SUMMER ADAPTIVE DFE FOR LOW POWER RECEIVER 31 3.3 SHARED SUMMER DFE 37 3.4 RECEIVER IMPLEMENTATION 42 3.5 MEASUREMENT RESULTS 45 CHAPTER 4 PAM-4 BAUD-RATE DIGITAL CDR 51 4.1 OVERVIEW 51 4.2 OVERALL ARCHITECTURE 53 4.2.1 PROPOSED BAUD-RATE CDR ARCHITECTURE 53 4.2.2 PROPOSED ANALOG FRONT-END STRUCTURE 59 4.3 STOCHASTIC PHASE DETECTION PAM-4 CDR 64 4.3.1 PROPOSED STOCHASTIC PHASE DETECTION 64 4.3.2 COMPARISON OF THE STOCHASTIC PD WITH SS-MMPD 70 4.4 PHASE DETECTION FOR MULTI-LEVEL SIGNALING 73 4.4.1 PROPOSED BAUD-RATE PHASE DETECTOR FOR MULTI-LEVEL SIGNAL 73 4.4.2 DATA LEVEL AND DFE COEFFICIENT ADAPTATION 79 4.4.3 PROPOSED PHASE DETECTOR 84 4.5 MEASUREMENT RESULT 88 4.5.1 MEASUREMENT OF THE PROPOSED STOCHASTIC BAUD-RATE PHASE DETECTION 94 4.5.2 MEASUREMENT OF THE PROPOSED BAUD-RATE PHASE DETECTION FOR MULTI-LEVEL SIGNAL 97 CHAPTER 5 CONCLUSION 103 BIBLIOGRAPHY 105 초 록 109박

Digital Signal Processing on FPGA for Short-Range Optical Communications Systems over Plastic Optical Fiber

Nowadays bandwidth requirements are increasing vertiginously. As new ways and concepts of how to share information emerge, new ways of how to access the web enter the market. Computers and mobile devices are only the beginning, the spectrum of web products and services such as IPTV, VoIP, on-line gaming, etc has been augmented by the possibility to share, store data, interact and work on the Cloud. The rush for bandwidth has led researchers from all over the world to enquire themselves on how to achieve higher data rates, and it is thanks to their efforts, that both long-haul and short-range communications systems have experienced a huge development during the last few years. However, as the demand for higher information throughput increases traditional short-range solutions reach their lim- its. As a result, optical solutions are now migrating from long-haul to short-range communication systems. As part of this trend, plastic optical fiber (POF) systems have arisen as promising candidates for applications where traditional glass optical fibers (GOF) are unsuitable. POF systems feature a series of characteristics that make them very suitable for the market requirements. More in detail, these systems are low cost, robust, easy to handle and to install, flexible and yet tolerant to bendings. Nonetheless, these features come at the expense of a considerable higher bandwidth limitation when compared to GOF systems. This thesis is aimed to the investigate the use of digital signal processing (DSP) algorithms to overcome the bandwidth limitation in short-range optical communications system based on POF. In particular, this dissertation presents the design and development of DSP algorithms on field programmable gate arrays (FPGAs) with the ultimate purpose of implementing a fully engineered 1Gbit/s Ethernet Media Converter capable of establishing data links over 50+ meters of PMMA-SI POF using an RC-LED as transmitte

Energy-Efficient Receiver Design for High-Speed Interconnects

High-speed interconnects are of vital importance to the operation of high-performance computing and communication systems, determining the ultimate bandwidth or data rates at which the information can be exchanged. Optical interconnects and the employment of high-order modulation formats are considered as the solutions to fulfilling the envisioned speed and power efficiency of future interconnects. One common key factor in bringing the success is the availability of energy-efficient receivers with superior sensitivity. To enhance the receiver sensitivity, improvement in the signal-to-noise ratio (SNR) of the front-end circuits, or equalization that mitigates the detrimental inter-symbol interference (ISI) is required. In this dissertation, architectural and circuit-level energy-efficient techniques serving these goals are presented. First, an avalanche photodetector (APD)-based optical receiver is described, which utilizes non-return-to-zero (NRZ) modulation and is applicable to burst-mode operation. For the purposes of improving the overall optical link energy efficiency as well as the link bandwidth, this optical receiver is designed to achieve high sensitivity and high reconfiguration speed. The high sensitivity is enabled by optimizing the SNR at the front-end through adjusting the APD responsivity via its reverse bias voltage, along with the incorporation of 2-tap feedforward equalization (FFE) and 2-tap decision feedback equalization (DFE) implemented in current-integrating fashion. The high reconfiguration speed is empowered by the proposed integrating dc and amplitude comparators, which eliminate the RC settling time constraints. The receiver circuits, excluding the APD die, are fabricated in 28-nm CMOS technology. The optical receiver achieves bit-error-rate (BER) better than 1E−12 at −16-dBm optical modulation amplitude (OMA), 2.24-ns reconfiguration time with 5-dB dynamic range, and 1.37-pJ/b energy efficiency at 25 Gb/s. Second, a 4-level pulse amplitude modulation (PAM4) wireline receiver is described, which incorporates continuous time linear equalizers (CTLEs) and a 2-tap direct DFE dedicated to the compensation for the first and second post-cursor ISI. The direct DFE in a PAM4 receiver (PAM4-DFE) is made possible by the proposed CMOS track-and-regenerate slicer. This proposed slicer offers rail-to-rail digital feedback signals with significantly improved clock-to-Q delay performance. The reduced slicer delay relaxes the settling time constraint of the summer circuits and allows the stringent DFE timing constraint to be satisfied. With the availability of a direct DFE employing the proposed slicer, inductor-based bandwidth enhancement and loop-unrolling techniques, which can be power/area intensive, are not required. Fabricated in 28-nm CMOS technology, the PAM4 receiver achieves BER better than 1E−12 and 1.1-pJ/b energy efficiency at 60 Gb/s, measured over a channel with 8.2-dB loss at Nyquist frequency. Third, digital neural-network-enhanced FFEs (NN-FFEs) for PAM4 analog-to-digital converter (ADC)-based optical interconnects are described. The proposed NN-FFEs employ a custom learnable piecewise linear (PWL) activation function to tackle the nonlinearities with short memory lengths. In contrast to the conventional Volterra equalizers where multipliers are utilized to generate the nonlinear terms, the proposed NN-FFEs leverage the custom PWL activation function for nonlinear operations and reduce the required number of multipliers, thereby improving the area and power efficiencies. Applications in the optical interconnects based on micro-ring modulators (MRMs) are demonstrated with simulation results of 50-Gb/s and 100-Gb/s links adopting PAM4 signaling. The proposed NN-FFEs and the conventional Volterra equalizers are synthesized with the standard-cell libraries in a commercial 28-nm CMOS technology, and their power consumptions and performance are compared. Better than 37% lower power overhead can be achieved by employing the proposed NN-FFEs, in comparison with the Volterra equalizer that leads to similar improvement in the symbol-error-rate (SER) performance.</p

Available Techniques for Magnetic Hard Disk Drive Read Channel Equalization

This paper presents an extensive, non-exhaustive, study of available hard disk drive read channel equalization techniques used in the storage and readback of magnetically stored information. The physical elements and basic principles of the storage processes are introduced together with the basic theoretical definitions and models. Both read and write processes in magnetic storage are explained along with the definition of simple key concepts such as user bit density, intersymbol interference, linear and areal density, read head pulse response models, and coding algorithm

Advanced DSP Techniques for High-Capacity and Energy-Efficient Optical Fiber Communications

The rapid proliferation of the Internet has been driving communication networks closer and closer to their limits, while available bandwidth is disappearing due to an ever-increasing network load. Over the past decade, optical fiber communication technology has increased per fiber data rate from 10 Tb/s to exceeding 10 Pb/s. The major explosion came after the maturity of coherent detection and advanced digital signal processing (DSP). DSP has played a critical role in accommodating channel impairments mitigation, enabling advanced modulation formats for spectral efficiency transmission and realizing flexible bandwidth. This book aims to explore novel, advanced DSP techniques to enable multi-Tb/s/channel optical transmission to address pressing bandwidth and power-efficiency demands. It provides state-of-the-art advances and future perspectives of DSP as well