Design of circuits for sub-threshold voltages : implementation of adders

The demand and the need for low-power circuits is an ever increasing trend particularly due to the added overhead of design of efficient cooling systems or more sophisticated and expensive packaging techniques. In most new emerging applications that demand low power consumption such as biomedical implants, wearable devices, micro-sensor nodes and countless others, energy efficiency emphasis far supersedes the traditional focus on improving the speed. Such energy constrained systems can be operated at considerably reduced performance levels in order to save power and extend their battery lifetimes. Sub-Threshold design has proven useful for ultra-low power and low energy applications since the dynamic power is reduced quadratically with supply voltage; the least energy operation usually takes place in the sub-threshold region. This work provides a comprehensive analysis of the CMOS standard cell characterization in the sub-threshold region, layout, logical library extraction, optimization and top-level implementation of 2 of the parallel prefix adders of different word sizes in 45nm technology with comparison between the sub-threshold region and strong inversion regions of operation. The analysis is done on PPA: power (energy), performance and area, the common metrics for any chip design. The switching activities of the circuits were captured using dynamic gate level simulation to perform the time based peak power analysis. Static timing analysis was performed to estimate the delay of the critical path for each circuit. The analysis and results presented in this report will be helpful in choosing a specific adder configuration for an integrated circuit based on the constraints related to its application.Electrical and Computer Engineerin

DeSyRe: on-Demand System Reliability

The DeSyRe project builds on-demand adaptive and reliable Systems-on-Chips (SoCs). As fabrication technology scales down, chips are becoming less reliable, thereby incurring increased power and performance costs for fault tolerance. To make matters worse, power density is becoming a significant limiting factor in SoC design, in general. In the face of such changes in the technological landscape, current solutions for fault tolerance are expected to introduce excessive overheads in future systems. Moreover, attempting to design and manufacture a totally defect and fault-free system, would impact heavily, even prohibitively, the design, manufacturing, and testing costs, as well as the system performance and power consumption. In this context, DeSyRe delivers a new generation of systems that are reliable by design at well-balanced power, performance, and design costs. In our attempt to reduce the overheads of fault-tolerance, only a small fraction of the chip is built to be fault-free. This fault-free part is then employed to manage the remaining fault-prone resources of the SoC. The DeSyRe framework is applied to two medical systems with high safety requirements (measured using the IEC 61508 functional safety standard) and tight power and performance constraints

Design of Low-Voltage Digital Building Blocks and ADCs for Energy-Efficient Systems

Increasing number of energy-limited applications continue to drive the demand for designing systems with high energy efficiency. This tutorial covers the main building blocks of a system implementation including digital logic, embedded memories, and analog-to-digital converters and describes the challenges and solutions to designing these blocks for low-voltage operation

Digital-Based Analog Processing in Nanoscale CMOS ICs for IoT Applications

L'abstract è presente nell'allegato / the abstract is in the attachmen

An IoT Endpoint System-on-Chip for Secure and Energy-Efficient Near-Sensor Analytics

Near-sensor data analytics is a promising direction for IoT endpoints, as it minimizes energy spent on communication and reduces network load - but it also poses security concerns, as valuable data is stored or sent over the network at various stages of the analytics pipeline. Using encryption to protect sensitive data at the boundary of the on-chip analytics engine is a way to address data security issues. To cope with the combined workload of analytics and encryption in a tight power envelope, we propose Fulmine, a System-on-Chip based on a tightly-coupled multi-core cluster augmented with specialized blocks for compute-intensive data processing and encryption functions, supporting software programmability for regular computing tasks. The Fulmine SoC, fabricated in 65nm technology, consumes less than 20mW on average at 0.8V achieving an efficiency of up to 70pJ/B in encryption, 50pJ/px in convolution, or up to 25MIPS/mW in software. As a strong argument for real-life flexible application of our platform, we show experimental results for three secure analytics use cases: secure autonomous aerial surveillance with a state-of-the-art deep CNN consuming 3.16pJ per equivalent RISC op; local CNN-based face detection with secured remote recognition in 5.74pJ/op; and seizure detection with encrypted data collection from EEG within 12.7pJ/op.Comment: 15 pages, 12 figures, accepted for publication to the IEEE Transactions on Circuits and Systems - I: Regular Paper

Wireless body sensor networks for health-monitoring applications

This is an author-created, un-copyedited version of an article accepted for publication in Physiological Measurement. The publisher is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at http://dx.doi.org/10.1088/0967-3334/29/11/R01

Ultra low-power fault-tolerant SRAM design in 90nm CMOS technology

With the increment of mobile, biomedical and space applications, digital systems with low-power consumption are required. As a main part in digital systems, low-power memories are especially desired. Reducing the power supply voltages to sub-threshold region is one of the effective approaches for ultra low-power applications. However, the reduced Static Noise Margin (SNM) of Static Random Access Memory (SRAM) imposes great challenges to the subthreshold SRAM design. The conventional 6-transistor SRAM cell does not function properly at sub-threshold supply voltage range because it has no enough noise margin for reliable operation. In order to achieve ultra low-power at sub-threshold operation, previous research work has demonstrated that the read and write decoupled scheme is a good solution to the reduced SNM problem. A Dual Interlocked Storage Cell (DICE) based SRAM cell was proposed to eliminate the drawback of conventional DICE cell during read operation. This cell can mitigate the singleevent effects, improve the stability and also maintain the low-power characteristic of subthreshold SRAM, In order to make the proposed SRAM cell work under different power supply voltages from 0.3 V to 0.6 V, an improved replica sense scheme was applied to produce a reference control signal, with which the optimal read time could be achieved. In this thesis, a 2K ~8 bits SRAM test chip was designed, simulated and fabricated in 90nm CMOS technology provided by ST Microelectronics. Simulation results suggest that the operating frequency at VDD = 0.3 V is up to 4.7 MHz with power dissipation 6.0 ƒÊW, while it is 45.5 MHz at VDD = 0.6 V dissipating 140 ƒÊW. However, the area occupied by a single cell is larger than that by conventional SRAM due to additional transistors used. The main contribution of this thesis project is that we proposed a new design that could simultaneously solve the ultra low-power and radiation-tolerance problem in large capacity memory design

Digital-based analog processing in nanoscale CMOS ICs for IoT applications

The Internet-of-Things (IoT) concept has been opening up a variety of applications, such as urban and environmental monitoring, smart health, surveillance, and home automation. Most of these IoT applications require more and more power/area efficient Complemen tary Metal–Oxide–Semiconductor (CMOS) systems and faster prototypes (lower time-to market), demanding special modifications in the current IoT design system bottleneck: the analog/RF interfaces. Specially after the 2000s, it is evident that there have been significant improvements in CMOS digital circuits when compared to analog building blocks. Digital circuits have been taking advantage of CMOS technology scaling in terms of speed, power consump tion, and cost, while the techniques running behind the analog signal processing are still lagging. To decrease this historical gap, there has been an increasing trend in finding alternative IC design strategies to implement typical analog functions exploiting Digital in-Concept Design Methodologies (DCDM). This idea of re-thinking analog functions in digital terms has shown that Analog ICs blocks can also avail of the feature-size shrinking and energy efficiency of new technologies. This thesis deals with the development of DCDM, demonstrating its compatibility for Ultra-Low-Voltage (ULV) and Power (ULP) IoT applications. This work proves this state ment through the proposing of new digital-based analog blocks, such as an Operational Transconductance Amplifiers (OTAs) and an ac-coupled Bio-signal Amplifier (BioAmp). As an initial contribution, for the first time, a silicon demonstration of an embryonic Digital-Based OTA (DB-OTA) published in 2013 is exhibited. The fabricated DB-OTA test chip occupies a compact area of 1,426 µm2 , operating at supply voltages (VDD) down to 300 mV, consuming only 590 pW while driving a capacitive load of 80pF. With a Total Harmonic Distortion (THD) lower than 5% for a 100mV input signal swing, its measured small-signal figure of merit (FOMS) and large-signal figure of merit (FOML) are 2,101 V −1 and 1,070, respectively. To the best of this thesis author’s knowledge, this measured power is the lowest reported to date in OTA literature, and its figures of merit are the best in sub-500mV OTAs reported to date. As the second step, mainly due to the robustness limitation of previous DB-OTA, a novel calibration-free digital-based topology is proposed, named here as Digital OTA (DIG OTA). A 180-nm DIGOTA test chip is also developed exhibiting an area below the 1000 µm2 wall, 2.4nW power under 150pF load, and a minimum VDD of 0.25 V. The proposed DIGOTA is more digital-like compared with DB-OTA since no pseudo-resistor is needed. As the last contribution, the previously proposed DIGOTA is then used as a building block to demonstrate the operation principle of power-efficient ULV and ultra-low area (ULA) fully-differential, digital-based Operational Transconductance Amplifier (OTA), suitable for microscale biosensing applications (BioDIGOTA) such as extreme low area Body Dust. Measured results in 180nm CMOS confirm that the proposed BioDIGOTA can work with a supply voltage down to 400 mV, consuming only 95 nW. The BioDIGOTA layout occupies only 0.022 mm2 of total silicon area, lowering the area by 3.22X times compared to the current state of the art while keeping reasonable system performance, such as 7.6 Noise Efficiency Factor (NEF) with 1.25 µVRMS input-referred noise over a 10 Hz bandwidth, 1.8% of THD, 62 dB of the common-mode rejection ratio (CMRR) and 55 dB of power supply rejection ratio (PSRR). After reviewing the current DCDM trend and all proposed silicon demonstrations, the thesis concludes that, despite the current analog design strategies involved during the analog block development

A system-on-chip digital pH meter for use in a wireless diagnostic capsule

This paper describes the design and implementation of a system-on-chip digital pH meter, for use in a wireless capsule application. The system is organized around an 8-bit microcontroller, designed to be functionally identical to the Motorola 6805. The analog subsystem contains a floating-electrode ISFET, which is fully compatible with a commercial CMOS process. On-chip programmable voltage references and multiplexors permit flexibility with the minimum of external connections. The chip is designed in a modular fashion to facilitate verification and component re-use. The single-chip pH meter can be directly connected to a personal computer, and gives a response of 37 bits/pH, within an operating range of 7 pH units