Design methodology for general enhancement of a single-stage self-compensated folded-cascode operational transconductance amplifiers in 65 nm CMOS process

The problems resulting from the use of nano-MOSFETs in the design of operational trans-conductance amplifiers (OTAs) lead to an urgent need for new design techniques to produce high-performance metrics OTAs suitable for very high-frequency applications. In this paper, the enhancement techniques and design equations for the proposed single-stage folded-cascode operational trans-conductance amplifiers (FCOTA) are presented for the enhancement of its various performance metrics. The proposed single-stage FCOTA adopts the folded-cascode (FC) current sources with cascode current mirrors (CCMs) load. Using 65 nm complementary metal-oxide semiconductor (CMOS) process from predictive technology model (PTM), the HSPICE2019-based simulation results show that the designed single-stage FCOTA can achieve a high open-loop differential-mode DC voltage gain of 65.64 dB, very high unity-gain bandwidth of 263 MHz, very high stability with phase-margin of 73°, low power dissipation of 0.97 mW, very low DC input-offset voltage of 0.14 uV, high swing-output voltages from −0.97 to 0.91 V, very low equivalent input-referred noise of 15.8 nV/Hz, very high common-mode rejection ratio of 190.64 dB, very high positive/negative slew-rates of 157.5/58.3 V⁄us, very fast settling-time of 5.1 ns, high extension input common-mode range voltages from −0.44to 1 V, and high positive/negative power-supply rejection ratios of 75.5/68.8 dB. The values of the small/large-signal figures-of-merits (s) are the highest when compared to other reported FCOTAs in the literature

A 0.3 V rail-to-rail ultra-low-power OTA with improved bandwidth and slew rate

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier

Performance enhancement in the desing of amplifier and amplifier-less circuits in modern CMOS technologies.

In the context of nowadays CMOS technology downscaling and the increasing demand of high performance electronics by industry and consumers, analog design has become a major challenge. On the one hand, beyond others, amplifiers have traditionally been a key cell for many analog systems whose overall performance strongly depends on those of the amplifier. Consequently, still today, achieving high performance amplifiers is essential. On the other hand, due to the increasing difficulty in achieving high performance amplifiers in downscaled modern technologies, a different research line that replaces the amplifier by other more easily achievable cells appears: the so called amplifier-less techniques. This thesis explores and contributes to both philosophies. Specifically, a lowvoltage differential input pair is proposed, with which three multistage amplifiers in the state of art are designed, analysed and tested. Moreover, a structure for the implementation of differential switched capacitor circuits, specially suitable for comparator-based circuits, that features lower distortion and less noise than the classical differential structures is proposed, an, as a proof of concept, implemented in a ΔΣ modulator

An ultra-low-voltage class-AB OTA exploiting local CMFB and body-to-gate interface

In this work a novel bulk-driven (BD) ultra-low-voltage (ULV) class-AB operational transconductance amplifier (OTA) which exploits local common mode feedback (LCMFB) strategies to enhance performance and robustness against process, voltage and temperature (PVT) variations has been proposed. The amplifier exploits body-to-gate (B2G) interface to increase the slew rate and attain class-AB behaviour, whereas two pseudo-resistors have been employed to increase the common mode rejection ratio (CMRR). The architecture has been extensively tested through Monte Carlo and PVT simulations, results show that the amplifier is very robust in terms of gain-bandwidth-product (GBW), power consumption and slew rate. A wide comparison against state-of-the-art has pointed out that best small-signal figures of merit are attained and good large-signal performance is guaranteed, also when worst-case slew rate is considered

A novel Digital OTA topology with 66-dB DC Gain and 12.3-kHz Bandwidth

The paper introduces an enhanced digital OTA topology which allows increasing the DC gain thanks to the adoption of an inverter-based output stage. Moreover, a new equivalent small-signal model is proposed which allows to simplify the circuit analysis and paves the way to new frequency compensation strategies. Designed using a 28-nm standard CMOS technology and working at 0.3-V power supply, post-layout simulations show a 66-dB gain and a 12.3-kHz gain bandwidth product while driving a 250-pF capacitive load. As compared to other ultra-low-voltage OTAs in literature, an increase of small and large signal performance, respect to area occupation, equal to 4.6X and 1.5X, respectively, is obtained

Design Techniques for High Speed Low Voltage and Low Power Non-Calibrated Pipeline Analog to Digital Converters

The profound digitization of modern microelectronic modules made Analog-to- Digital converters (ADC) key components in many systems. With resolutions up to 14bits and sampling rates in the 100s of MHz, the pipeline ADC is a prime candidate for a wide range of applications such as instrumentation, communications and consumer electronics. However, while past work focused on enhancing the performance of the pipeline ADC from an architectural standpoint, little has been done to individually address its fundamental building blocks. This work aims to achieve the latter by proposing design techniques to improve the performance of these blocks with minimal power consumption in low voltage environments, such that collectively high performance is achieved in the pipeline ADC. Towards this goal, a Recycling Folded Cascode (RFC) amplifier is proposed as an enhancement to the general performance of the conventional folded cascode. Tested in Taiwan Semiconductor Manufacturing Company (TSMC) 0.18?m Complementary Metal Oxide Semiconductor (CMOS) technology, the RFC provides twice the bandwidth, 8-10dB additional gain, more than twice the slew rate and improved noise performance over the conventional folded cascode-all at no additional power or silicon area. The direct auto-zeroing offset cancellation scheme is optimized for low voltage environments using a dual level common mode feedback (CMFB) circuit, and amplifier differential offsets up to 50mV are effectively cancelled. Together with the RFC, the dual level CMFB was used to implement a sample and hold amplifier driving a singleended load of 1.4pF and using only 2.6mA; at 200MS/s better than 9bit linearity is achieved. Finally a power conscious technique is proposed to reduce the kickback noise of dynamic comparators without resorting to the use of pre-amplifiers. When all techniques are collectively used to implement a 1Vpp 10bit 160MS/s pipeline ADC in Semiconductor Manufacturing International Corporation (SMIC) 0.18[mu]m CMOS, 9.2 effective number of bits (ENOB) is achieved with a near Nyquist-rate full scale signal. The ADC uses an area of 1.1mm2 and consumes 42mW in its analog core. Compared to recent state-of-the-art implementations in the 100-200MS/s range, the presented pipeline ADC uses the least power per conversion rated at 0.45pJ/conversion-step

Power-Efficient and High-Performance Cicruit Techniques for On-Chip Voltage Regulation and Low-Voltage Filtering

This dissertation focuses on two projects. The first one is a power supply rejection (PSR) enhanced with fast settling time (TS) bulk-driven feedforward (BDFF) capacitor-less (CL) low-dropout (LDO) regulator. The second project is a high bandwidth (BW) power adjustable low-voltage (LV) active-RC 4th -order Butterworth low pass filter (LPF). As technology improves, faster and more accurate LDOs with high PSR are going to be required for future on-chip applications and systems.The proposed BDFF CL-LDO will accomplish an improved PSR without degrading TS. This would be achieved by injecting supply noise through the pass device’s bulk terminal in order to cancel the supply noise at the output. The supply injection will be achieved by creating a feedforward path, which compared to feedback paths, that doesn’t degrade stability and therefore allows for faster dynamic performance. A high gain control loop would be used to maintain a high accuracy and dc performance, such as line/load regulation. The proposed CL-LDO will target a PSR better than – 90 dB at low frequencies and – 60 dB at 1 MHz for 50 mA of load current (IvL). The CL-LDO will target a loop gain higher than 90 dB, leading to an improved line and load regulation, and unity-gain frequency (UGF) higher than 20 MHz, which will allow a TS faster than 500 ns. The CL-LDO is going to be fabricated in a CMOS 130 nm technology; consume a quiescent current (IQ) of less than 50 μA; for a dropout voltage of 200 mV and an IvL of 50 mA. As technology scales down, speed and performance requirements increase for on-chip communication systems that reflect the current demand for high speed data-oriented applications. However, in small technologies, it becomes harder to achieve high gain and high speed at the same time because the supply voltage (VvDvD) decreases leaving no room for conventional high gain CMOS structures. The proposed active-RC LPF will accomplish a LV high BW operation that would allow such disadvantages to be overcome. The LPF will be implemented using an active RC structure that allows for the high linearity such communication systems demand. In addition, built-in BW and power configurability would address the demands for increased flexibility usually required in such systems. The proposed LV LPF will target a configurable cut-off frequency (ƒо) of 20/40/80/160 MHz with tuning capabilities and power adjustability for each ƒо. The filter will be fabricated in a CMOS 130 nm technology. The filter characteristics are as following: 4th -order, active-RC, LPF, Butterworth response, VDD = 0.6 V, THD higher than 40 dB and a third-order input intercept point (IIP3) higher than 10 dBm

Voltage and Time-Domain Analog Circuit Techniques for Scaled CMOS Technologies

CMOS technology scaling has resulted in reduced supply voltage and intrinsic voltage gain of the transistor. This presents challenges to the analog circuit designers due to lower signal swing and achievable signal to noise ratio (SNR), leading to increased power consumption. At the same time, device speed has increased in lower design nodes, which has not been directly beneficial for analog circuit design. This thesis presents voltage-domain and time-domain circuit scaling friendly circuit architectures that minimize the power consumption and benefit from the increasing transistor speeds. In the voltage-domain, an on-the-fly gain selection block is demonstrated as an alternative to the traditional MDAC architecture to enhance the input dynamic range of a medium-resolution medium-speed analog-to-digital converter (ADC) at reduced supply voltages. The proposed design also eliminates the need for a reference buffer, thus providing power savings. The measured prototype enhances the input dynamic range of a 12bit, 40MSPS ADC to 80.6dB at 1.2V supply voltage. In the time-domain, a generic circuit design approach is presented, followed by an in-depth analysis of Voltage-Controlled-Oscillator based Operational Transconductance Amplifiers (VCO-OTAs). A discrete-time-domain small-signal model based on the zero crossings of the internal VCOs is developed to predict the stability, the step response, and the frequency response of the circuit when placed in feedback. The model accurately predicts the circuit behavior for an arbitrary input frequency, even as the VCO free-running frequency approaches the unity-gain bandwidth of the closed-loop system, where other intuitive small-signal models available in the literature fail. Next, we present an application of VCO-OTA in designing a baseband trans-impedance amplifier (TIA) for current-mode receivers as a scaling-friendly and power-efficient alternative to the inverter-based OTA. We illustrate a design methodology for the choice of the VCO-OTA parameters in the context of a receiver design with an example of a 20MHz RF-channel-bandwidth receiver operating at 2GHz. Receiver simulation results demonstrate an improvement of up to 12dB in blocker 1dB compression point (B1dB) for slightly higher power consumption or up to 2.6x power reduction of the TIA resulting in up to 2x power reduction of the receiver for similar B1dB performance. Next, we present some examples of VCO-OTAs. We first illustrate the benefit of a VCO-OTA in a low-dropout-voltage regulator to achieve a dropout voltage of only100mV and operating down to 0.8V input supply, compared to the prototype based on traditional OTA with a minimum dropout voltage of 150mV, operating at a minimum of 1.2V supply. Both the capacitor-less prototypes can drive up to 1nF load capacitor and provide a current of 60mA. The next prototype showcases a method to reduce the power consumption of a VCO-OTA and spurs at the VCO frequency, with an application in the design of a fourth-order Butterworth filter at 4MHz. The thesis concludes with a design example of 0.2V VCO-OTA